Operating The Remote Control Unit; Operating Denon Audio Components; Setting The Preset Memory Function; Setting The Punch Through Function - Denon DRA-397 Operating Instructions Manual
Am-fm stereo receiver
Hide thumbs
Also See for DRA-397:
- Brochure & specs (2 pages) ,
- Service manual (63 pages) ,
- Operating instructions manual (39 pages)
Table of Contents
Advertisement
Operating the remote control unit
Operating DENON audio components
1
[MODE SELECTOR 1]
Set
to "A" or "B".
2
[MODE SELECTOR 2]
Set
to the position for the
component to be operated.
3
Operate the audio component.
For details, refer to the component's operating instructions.
While this remote control is compatible with a wide range of
infrared controlled components, it may be the case that some
component models cannot be operated with this remote control.
Setting the preset memory function
• DENON and other makes of components can be operated by setting
the preset memory.
• This remote control unit can be used to operate components of
other manufacturers without using the learning function by
registering the manufacturer of the component as shown in the list
of preset codes (
End of this manual).
• Operation is not possible for some models.
1
[MODE SELECTOR 1]
Set
to "A" or "B".
Set to the A side for the CD/iPod, TV, DBS/CABLE or DVD
position, and to the B side for the CD-R/TAPE or VCR position.
2
[MODE SELECTOR 2]
Set
to the component to be
registered.
3
[ZONE2 OFF]
[ZONE3 ON]
Press
and
• The indicator starts flashing.
4
Referring to the included list of preset codes, press
[NUMBER]
to input the preset code (a 3-digit number)
for the manufacturer of the component whose signals
you want to store in the memory.
5
To store the codes of another component in the
memory, repeat steps 1 to 4.
• The signals for the pressed buttons are emitted while setting the
preset memory. To avoid accidental operation, cover the remote
control unit's transmitting window while setting the preset memory.
• Depending on the model and year of manufacture, this function
cannot be used for some models, even if they are of makes listed in
the list of preset codes.
• Some manufacturers use more than one type of remote control
code. Refer to the included list of preset codes to change the
number and verify correct operation.
• The preset memory can be set for one component only among the
following: CD/iPod, DBS/CABLE and CD-R/TAPE.
at the same time.
Setting the punch through function
"Punch Through" is a function allowing you to operate
6
components when in the TV or DBS/CABLE mode. By default, nothing
is set.
1
2
3
4
Operating a component stored in the preset
memory
1
2
3
20
ENGLISH
,
,
and
on CD, DVD/VDP, TAPE/CD-R/MD or VCR
7
8
9
[MODE SELECTOR 1]
Set
to "A".
[MODE SELECTOR 2]
Set
to the component to be
registered (TV or DBS/CABLE).
[A]
[D]
Press
and
at the same time.
• The indicator starts flashing.
Input the number of the component you want to set.
No.
CD
1
DVD/VDP
2
TAPE/CD-R/MD
3
VCR
4
No setting
0
[MODE SELECTOR 1]
Set
to "A" or "B".
Set to the A side for the CD/iPod, TV, DBS/CABLE or DVD
position, and to the B side for the CD-R/TAPE or VCR position.
[MODE SELECTOR 2]
Set
to the component you want
to operate.
Operate the component.
For details, refer to the component's operating instructions.
Some models cannot be operated with this remote control unit.
ENGLISH
,
,
,
,
1
2
0
3
Hide quick links:
Advertisement
Table of Contents
