Cateye ASTRALE User Manual page 3

Wire Securing/Bracket Mounting
Outer Cable
(1) Clamp the wire with the wire se-
Wire curing tape and wire clip as
shown in Fig.1 &2. Wind the wire
around the outer cable to reach
the handlebar and adjust the
1
length. Loosen the wire in the
Wire
Securing Tape
Wire Clip area marked with the arrow
that the wire does not hinder
handlebar operation.
Wire Wire Clip
(2) Use either the 1mm or 2mm thick
rubber pad if necessary, accord-
2
ing to the handlebar diameter as
shown in Fig.3.
Screw
Bracket
3
Screw Cap
Main Unit Mounting
Slide
Front
Mount the main unit onto the bracket by sliding it from front to
the rear until it clicks into position. When removing it, while
pushing the lever, slide it off forward.
Test
Mount the main unit on the bracket. Lift the rear wheel off the
ground and spin the wheel checking that Current Speed (S) is
displayed. Also, revolve the pedal to check that Cadence (C) is
displayed. If not, adjust positions of magnet and sensor follow-
ing the instruction on „Magnet Mounting„. Refer to the following
pages for the operation of the main unit.
Mounting To Bike
CYCLOCOMPUTER
MODEL CC-CD100
so
Lever
Cadence Sensor/Magnet Mounting
Wire Clip
Wire Securing
Tape
1
Center of Magnet
Cadence Sensor
Center of Magnet
3
Cadence Magnet
CCMCD1-970210 0687281
Screw
(1) Securely fasten the ca-
dence magnet on the in-
side of the left crank with
the adhesive tape and
wire clip. (Fig.1)
(2) Attach the Cadence Sen-
2
Cadence Sensor
sor to the front area of the
left chain stay by using
Sensor Band-A(L) & -
B(L), in the same proce-
Cadence Sensor
dure as the Wheel Sensor
Cadence Magnet
(Fig.2). Align the Center of
Magnet and Marking Line
of the Sensor, and make
sure of approx. 1mm
4
clearance between them
approx. 1mm
(Fig.3,4).
Wheel Sensor/Magnet Mounting
Wheel Magnet
(1)The spokes must run correctly through the
R Spoke
inside of the magnet as in Fig.1.
5A
(2)Attach the Wheel Sensor to the rear area
1
of the left chain stay with Sensor Band-
Screw
A(S) & -B(S), following the instruction be-
low (Fig.4):
Sensor Band B
1.Insert the Band-B into the slit of the
Band-A, and put the Rubber Pad inside
Rubber Pad
of the Band-A (Fig.2). Adjust the length
in order that the screw-fastening part of
2
the Bands are parallel when mounted to
Sensor Band A
the chain stay (Fig.3).
Sensor Band B
*To pull out the Band- B from Band-A,
tug strongly.
Rubber Pad
2.Mount the adjusted Bands to the chain
Sensor Band A
stay along with the Wheel Sensor, by
3
temporarily tightening the screw (Fig.5).
Align the Center of Magnet and the
Parallel
Sensor's Marking Line, and make sure
Wheel Sensor
of 1mm clearance between the Magnet
and Sensor (Fig.4,6). Then tighten the
screw securely. Cut the excess of the
Band-B with a nipper or the like.
*Figure 7 shows how to attach the wheel
Wheel Magnet
4
magnet on ATB or MTB bikes, where
Center of Magnet
the gap between the chainstay and
Wire Securing Tape
spoke is extra wide. Attach the sensor
Screw
as close to the wheel magnet as pos-
sible, but don't let them touch one an-
other.
5
Wheel Sensor
Wheel Sensor
Wheel Magnet
6
approx. 1mm
7
Wheel Sensor