Sign in today to find solutions:

Forgot your password?

Don't have an account? Sign up

UNIVERSAL REMOTE CONTROL UR4U-MDVR-CHD2 - MOTOROLA AND SCIENTIFIC ATLANTA DIGITAL Operating Instructions

 
Introduction
1
Operating Instructions
This remote control is designed to operate all
For 4-Function
Motorola and Scientific Atlanta digital set top
boxes (including HD and DVR), plus the
majority of TVs, VCRs, DVDs and AUDIO
Cable Remote Control
equipment on the market as shown below.
CABLE : Cable Converters
DVD : DVDs, TV/DVDs, VCRs and TV/VCRs
UR4U-MDVR-CHD2
AUX : Audio Receivers and DVRs, etc.
2
Replacing Batteries
Before you program or operate this remote
control, you must first install two new AA Alkaline
batteries.
STEP1 Remove the battery compartment cover
on the back of your remote control.
STEP2 Check battery polarity carefully, and
install the batteries as shown in the
illustration below.
STEP3 Replace the battery compartment cover.
3
Operations
DEFAULT STATUS:
Component Default: CABLE
Channel Default: CABLE channel +/- and
numbers operate through the CABLE box.
You have the option of controlling channel +/-
and numbers through the TV, VCR or DVD.
Refer to section F for programming steps.
Volume Default: CABLE volume +/- and mute
operate through the TV. You have the option
Universal Remote Control, Inc.
of controlling volume through the Cable box,
VCR or DVD. Refer to section G for
www.universalremote.com
OCE-0053A REV 02 (03/21/07)
programming steps.
Button Functions
4
TV : Televisions
5
Programming the Remote Control
There are two ways you can program your remote control:
* The
Pre-Programm
rogrammed 3-Digit Code Method
* The Auto-Search Method
The Pre-Programmed Code Method allows you to setup all the buttons at once by entering 3-digit
code numbers that correspond to a particular Component's manufacturer/brand, so it's the fastest
and easiest of the two methods. (Code Tables are on the backside of this Instruction Sheet.) The
Auto-Search Method scans through all the codes in the remote control, one at a time.
IMPORTANT SETUP NOTES:
This pertains to all programming steps. When you are in setup mode in each component, a
component LED will light up for 30 seconds. If you do not press a button within 30 seconds, the LED
light will turn off and exit setup mode and you will need to start over.
When programming a combo unit, program as a VCR or DVD first.
A. Pre-Programmed 3-Digit Code Method
STEP1 Turn on the Component you want to program (TV, VCR, DVD or AUX) .
STEP2 Press the [COMPONENT] button (TV,
STEP4 Test functions. (Same as for 3-Digit Code
DVD or AUX) to be programmed and
Programming Method - Section A). If any
[OK/SEL] button simultaneously for 3
of the functions do not work as they
seconds. The Component LED will light
should, repeat from STEP 3 using [CH ]
for 30 seconds indicating the unit is
or [CH ] buttons to find the correct code.
ready to be programmed.
Save the code. (Same as for 3-Digit Code
STEP5
STEP3 Point the remote control toward the
Programming Method - Section A).
Component and enter the 3-digit code
Now, repeat the Auto-Search Method for those
number assigned to your brand.
Components you could not program earlier with
*Note : If the 3-digit code number you just
the Pre-Programmed Method.
entered is correct, the Component will
turn Off. If it did not turn Off, continue
C. Finding a Component Button's
entering code numbers listed for that
Setup Code Number
brand until the Component turns Off.
If you used the Auto-Search Method to program a
STEP4 After you've entered the correct code
Component, you may not know what the correct code
number and the Component has turned
number is. Here is a way for you to identify the code
Off, press the [POWER] button to turn
number, so you can record it for future reference.
the Component back On. Now it's time
STEP1
Press the [COMPONENT] button (TV, DVD
to test the VOLUME and MUTE buttons
or AUX) you want to verify and the [OK/SEL]
for the TV (or PLAY and STOP buttons
button simultaneously for 3 seconds. The
for VCR and DVD) to make sure they all
Component LED will light for 30 seconds.
work. If any of the functions do not
work as they should, repeat from STEP
STEP2
Press the [INFO] button and count the
3 using the next 3-digit code number
number of times the Component LED light
listed for that brand.
blinks. This number indicates the first
digit of the code, followed by the second
STEP5 Once you have found the correct 3-
and third, each separated by a one
digit code, save it by pressing the same
second pause when the LED will turn off.
[COMPONENT] button one more time.
The Component LED light will blink
*Note : 10 blinks represents the number zero.
twice to confirm that the code was
Example : One blink, (pause), eight blinks,
successfully stored.
(pause) and three blinks, indicates
Now, program the rest of your Components by
code number 183.
repeating STEPS 1-5.
D. AUX Function: Programming a 4
*Note : If the Pre-Programmed Method did
Component
not work, or if the Code Tables do not
list your Component brand, use the
You can take advantage of the AUX function to
Auto-Search Method as explained in
program a 4
th
Component such as a second TV,
Section B.
VCR, DVD or Audio Component.
STEP1
Turn on the 4
th
Component you want to
B. Auto-Search Method
program (TV, VCR, DVD or Audio).
STEP1 Turn on the Component you want to
Press the [AUX] button and the [OK/SEL]
STEP2
program (TV, VCR, DVD or AUX).
button simultaneously for 3 seconds.The
STEP2 Press the [COMPONENT] button (TV,
[AUX] Component LED will light for 30
DVD or AUX) to be programmed and
seconds.
[OK/SEL] button simultaneously for 3
Press the [COMPONENT] button you want
STEP3
seconds. The Component LED will light
to setup. Point the remote control toward
for 30 seconds indicating the unit is
the Component and enter the 3-digit code
ready to be programmed.
number assigned to your brand.
STEP3 Point the remote toward the
*Note : If the 3-digit code number you just
Component and press the [CH ] or
entered is the correct number, the
[CH ] button one step at a time or
Component will turn Off. If it did not turn
keep it pressed. The remote will emit a
Off, continue entering code numbers
series of ON/OFF commands. Release
listed for that brand until the Component
the [CH ] or [CH ] button as soon as
turns Off
the Component turns Off.
STEP4
Test functions. (Same as for 3-Digit Code
To return to original state:
Programming Method - Section A). If
If you wish to restore the CABLE channel control in
any of the functions do not work as they
TV mode, repeat the above steps but press [CBL]
should, you need to find a new code.
in
STEP3
.
Once you have found the correct 3-digit
STEP5
G. Programming Volume Control
code, save it by pressing the [AUX]
button one more time. The Component
You can program the volume controls (Volume Up,
LED light will blink twice to confirm the
Volume Down and Mute) from one Component to
code was stored. Now when you press
operate in another Component mode. Default
the AUX button, all the buttons will work
volume control settings on the remote control are
with that 4
th
Component.
as follows:
CBL : TV
E. Programming the System On/Off Button
DVD : TV
This allows you to program the System On/Off
If you wish to operate the CBL volume control in
button so it can send up to four power On/Off
CBL mode, use the following steps.
commands with one button press.
STEP1
Press the [CBL] button and the
STEP1
Press the [CBL] button.
[OK/SEL] button simultaneously for 3
seconds. The [CBL] Component LED
STEP2
Press the [SYSTEM ON/OFF] button and
will light for 30 seconds.
the [OK/SEL] button simultaneously for 3
Press the [VOL +] button.
seconds. The [CBL] Component LED will
STEP2
light for 30 seconds.
Press the [CBL] button.
STEP3
The Component LED will blink twice to
STEP3
Press the first [COMPONENT] button you
confirm the programming.
want to store in the [SYSTEM ON/OFF]
button and then the [POWER] button.
To return to original state:
Repeat this for other Components until
If you wish to restore the TV volume control in CBL
you have stored all the desired power
mode, repeat the above steps but press [TV] in
commands into the [SYSTEM ON/OFF]
STEP3
.
button.
H. Programming a Favorite Channel
Press the [CH+] button to save the power
STEP4
commands you stored. The [CBL] button
See on-screen Guide Menu.
will blink twice to confirm the commands
have been saved.
th
I. Low Battery Warning
When the batteries are low and need to be
F. Programming Channel Control
replaced with fresh batteries, the Component
LED lights will blink 2 times in sequence
You can program the channel controls (Channel Up,
whenever a [POWER] button is pressed to turn
Channel Down, Last and Numbers) from one
on equipment.
Component to operate in another Component mode.
Default channel control settings on the remote
J. Memory Lock System
control are as follows:
This remote control is designed to retain
CBL : CBL
T V : CBL
programmed memory for 10 years even after
DVD : DVD
AUX : AUX
batteries are removed from the remote control.
If you wish to operate the TV channel control in TV
K. Record Your Component Set-up
mode, use the following steps.
Codes
STEP1
Press the [TV] button and the [OK/SEL]
button simultaneously for 3 seconds.
TV
Set-up Code Number:
The [TV] Component LED will light for 30
DVD
Set-up Code Number:
seconds.
AUX
Set-up Code Number:
Press the [VOL -] button.
STEP2
STEP3
Press the [TV] button again.
The Component LED will blink twice to
confirm the programming.
T V : TV
AUX : AUX

Summary of Contents

  • Page 1

    When programming a combo unit, program as a VCR or DVD first. Component will turn Off. If it did not turn keep it pressed. The remote will emit a Universal Remote Control, Inc. of controlling volume through the Cable box, Off, continue entering code numbers STEP3 Press the [TV] button again.

  • Page 2

    DVD-VCR DVD-VCR AUX-AUDIO Set-up Code Tables Manufacturer/Brand Set-Up Code Number Manufacturer/Brand Set-Up Code Number Manufacturer/Brand Set-Up Code Number Manufacturer/Brand Set-Up Code Number Manufacturer/Brand Set-Up Code Number Manufacturer/Brand Set-Up Code Number Manufacturer/Brand Set-Up Code Number CABLE Converter 160 144 165 073 197 008 009 034 056 074 130 155 161 PORTLAND 143 363 ALLEGRO...

Comments to this Manuals

Symbols: 0

Latest comments:

×

Select the desired size and copy embed code

Copy your embed code and put on your site: