One for All 8011 User Manual

Use VOL+ (or VOL-) to raise (or lower) the
sound volume.
8 DEVICE HOME THEATER
UNIVERSAL REMOTE CONTROL
Press MUTE once to turn the sound off
or on.
In TV, VCR, DVD, SAT, and CBL modes, use FAV to
scan favorite channels and/or all channels.
(See Using Channel Scan and Programming
Favorite Channel Scan.)
Use CH+ (or CH-) to select the next higher (or
lower) channel.
Press PREV once to recall the last-viewed
channel and to page back one screen on
main menu.
In the RCVR/AMP mode, use PREV to select
the receiver band.
Use the keypad (1 ~ 9 and 0) to directly select
channels (for example, 009 or 031).
In the RCVR/AMP mode, use the keypad
(1 ~ 9 and 0) to select audio sources 1 through
10.
Press ENTER once after entering the
channel numbers on some TVs.
Use TV/VID to switch the TV's input to
view TV or video programs.
Use the transport keys to control your VCR,
DVD player, or VOD (Video On Demand) if
available on your cable or satellite service.
USER'S GUIDE To record a VCR program, press REC twice.
INTRODUCTION
Use MOVE to move the window picture
The One For All 8 Device Home Theater Universal Remote Control is
to different positions in the main picture.
designed to operate up to eight home entertainment devices, including
TV, video, and audio components. The remote control requires two (2)
Use PIP to switch the Picture-In-Picture
new AA alkaline batteries (not included) and easy programming to con-
feature on or off (if available on your TV).
trol your devices. For best results, please read and perform all instruc-
tions listed here.Also, keep these instructions for future reference.
Use SWAP to switch images and sound
between the main and window pictures.
FEATURES AND FUNCTIONS
Press SLEEP to activate your device's sleep
Use the Key Charts (below) to learn how to use the universal features and
timer (not available for all devices).
functions of the One For All 8 Device Home Theater Universal Remote
Control.
Key Charts
After programming, press MACRO once to
run a desired macro (see Using A Macro).
The LED (red light) blinks to show that
the remote control is working and is
Use to turn on or off the key backlight.When
sending signals.
this feature is activated, keys will remain back-
light for 5 seconds after the last key press.
Press TV, VCR, DVD, AUX, SAT, CBL, RCVR/AMP,
or CD once to select a desired home enter- Use SET for all programming sequences.
tainment device to control.
After programming, press HOME THEATER once
to select the home theater mode (see Using The
Home Theater Mode). INSTALLING BATTERIES
1. On the remote control's back, push the tab and lift off the
Press POWER once to turn on or off the
battery cover.
selected device.
Press MENU once to display your selected
device's main menu.
2. Obtain two (2) new AA alkaline batteries. Match the + and – marks
on the batteries to the + and – marks in the battery case, then insert
Use GUIDE to display your selected device's
the new batteries.
program guide or setup menu.
Use EXIT to exit from your selected device's
guide or menu.
Use INFO to display the current channel and
3. Press the battery cover back into place. The tab should click when the
program information.
cover is locked.
Use the cursor keys to move the cursor in the
program guide and menu screens.
Use SELECT to choose options from your
4. Test the remote control by first pressing POWER and then any mode
selected device's menu or guide.
key (e.g., TV). If batteries are inserted correctly, the LED (red light) will
blink once.
In the RCVR/AMP mode, use SELECT to
NOTE: When batteries need replacement, the remote control will stop
set the surround sound. Use (or ) operating. Remove the old batteries and insert new ones within 30 minutes to
to adjust the volume higher (or lower). Use ensure all of your programming information is restored.
(or ) to adjust the balance left
(or right).
SETTING UP YOUR COMPONENTS
TV/VCR Code:
The One For All 8 Device Home Theater Universal Remote Control is pre-
programmed at the factory to operate an RCA TV and VCR, a Motorola TV Code (if used):
(GI) cable box, an RCA satellite receiver, a Pioneer CD player, a Toshiba
DVD player, a Pioneer audio receiver/ amplifier, and a One For All home
automation device. To control devices other than the default brands, per- SEARCHING FOR YOUR CODE
form the following steps; otherwise skip this section:
If your device does not respond to the remote control after trying all codes
listed for your brand, or if your brand is not listed at all, try searching for
NOTE: For TV/VCR Combo control, see the next section.
your code.
1. Turn on a device (e.g.,VCR or DVD player) and, if applicable, insert
media (e.g., cassette or disc). For example, to search for a code for your TV:
1. On the remote control, press TV once.
NOTE: Please read steps 2 through 4 completely before proceeding. Highlight or
write down the codes and device you wish to program before starting step 2.
2. On the remote control, press a device key once (i.e.,
2. Press and hold SET until the LED (red light) blinks twice, then
TV, VCR, DVD, AUX, SAT, CBL, RCVR/AMP, or CD).
release SET.
3. Enter 9 - 9 - 1. The LED will blink twice.
NOTE: Use the AUX key to program control of home automation devices or miscel-
4. Aim the remote control at the the TV and slowly alternate
laneous audio services and video accessories. Alternately, use the AUX key to pro-
between pressing POWER and TV. Stop when the TV turns off.
gram control of a second device type (e.g., a second VCR; see "Re-assigning Device
NOTE: In the search mode, the remote control will send IR codes from
Keys").
its library to the selected device, starting with the most popular code
3. Press and hold SET until the LED (red light) blinks twice, then
first.
release SET.
5. To lock in the code, press and hold SET until the LED blinks
the
4. Use the Manufacturer's Codes (on the back) to locate the type of
twice, then release SET.
device and brand name and then enter the first four-digit code for
6. To search for the codes of your other devices, repeat steps 1 through 5,
your device. If performed correctly, the LED will blink twice.
but substitute the appropriate device key for the device you are
NOTE: If the LED did not blink twice, repeat steps 2 through 4 and try entering searching for.
the same code again.
5. Aim the remote control at the device and press POWER once.
CHECKING THE CODES
The device should turn off. If it does not respond, repeat steps
2 through 5, trying each code for your brand until you find one
If you have set up the remote control using the Searching For Your Code
that works. If it still does not work, try Searching For Your
procedure, you may need to find out which four-digit code is operating
Code.
your equipment. For example, to find out which code is operating your
TV:
NOTE: If the device does not have a POWER key, press the ( Play ) key.
6. Repeat steps 1 through 5 for each device you want to control. 1. On the remote control, press TV once.
For future reference, write down each working device code in the
boxes below:
2. Press and hold SET until the LED (red light) blinks twice, then
TV Code:
release SET.
Enter 9 - 9 - 0. The LED will blink twice.
3.
VCR Code:
4. To view the code for the first digit, press 1 once.Wait 3 seconds, count
the LED blinks (e.g., three blinks = 3) and write down
the number.
DVD Code:
NOTE: If a code digit is "0", the LED will not blink.
5. Repeat step 4 three more times for remaining digits. Use 2 for the
SAT Code:
second digit, 3 for the third digit, and 4 for the fourth digit.
6. To check for codes of other devices, repeat steps 1 through 5,
but substitute the appropriate device key for each device you
CBL Code:
are checking.
RCVR/AMP Code:
USING THE HOME THEATER MODE
The One For All 8 Device Home Theater Universal Remote Control
CD Code:
includes a custom Home Theater mode. After the HOME THEATER key is
programmed, it will allow you to access five groups of remote control
keys without having to change device modes.
AUX Code:
Control Organization
About Control Groups
Aux. Device Type: _______________________________
For Home Theater programming, the remote control's keys are grouped
by type of control into the following five control groups:
SETTING UP TV/VCR COMBO CONTROL
(1) Transport Controls: PLAY, STOP, FWD, REW, PAUSE, and REC
Perform the following instructions to control a TV/VCR Combo:
(2) Volume Controls: VOL+, VOL-, and MUTE
1. Turn on the TV/VCR Combo and insert a video cassette.
(3) Channel Controls: CH+, CH-, (Keypad) 0 ~ 9, ENTER, LAST,
SLEEP, INFO, and TV/VCR
NOTE: Please read steps 2 through 4 completely before proceeding. Highlight or
write down the codes and device you wish to program before starting step 2.
(4) Menu Controls: MENU, GUIDE, Cursor Controls (Up, Down,
Left, Right), SELECT, and EXIT
2. On the remote control, press VCR.
(5) PIP Controls: PIP, MOVE, and SWAP
About Device Groups
3. Press and hold SET until the LED (red light) blinks twice, then
release SET.
Moreover, the remote control's devices are grouped into the following five
device groups:
4. Use the Setup Codes For TV/VCR Combos (on the back) to locate the
brand name and then enter the first four-digit code for your device. If
(1) Device Group 1: VCR, DVD, CD, and RCVR/AMP
performed correctly, the LED will blink twice.
(2) Device Group 2: TV, VCR, CBL, SAT, CD, and RCVR/AMP
NOTE: If the LED did not blink twice, repeat steps 2 through 4 and try entering
(3) Device Group 3: TV, VCR, CBL, SAT, CD, and RCVR/AMP
the same code again.
(4) Device Group 4: TV, VCR, CBL, SAT, and DVD
5. the remote control at the device and press POWER once. It
should turn off. If the device does not respond, repeat steps 2
(5) Device Group 5: TV
through 5, trying each code for your brand until you find one
The default Device Group setting from the factory is:
that works. If it still does not work, try Searching For Your
Code.
(1) Device Group 1: VCR
NOTE: If the device does not have a POWER key, press the ( Play ) key.
(2) Device Group 2: TV
6. If you've located a setup code that works, but it has a separate TV
(3) Device Group 3: CBL
code, you'll also need to program it into the remote control to access
(4) Device Group 4: CBL
volume control as follows:
(5) Device Group 5: TV
a. Press TV once. The LED (red light) will blink twice.
Programming The Home Theater Mode
For example, let's assume you have a TV, a cable box, and a VCR in your
b. Enter the TV code for your TV/VCR Combo. If correct, the LED
home theater system.You can set up the Home Theater mode so that
will blink twice.
selected controls are assigned to these devices as follows:
NOTE: For VCR/TV Combos programmed with separate TV codes,
1. On the remote control, press HOME THEATER.
TV volume is controlled by pressing VCR first and then TV . After that, use VOL+
(or VOL- ) to raise (or lower) the TV volume. For other alternatives on controlling
your volume keys, see the "Changing Volume Lock" or "Using Keymover" sections.
2. Press and hold SET until the LED (red light) blinks twice, then
7. For future reference, write down the working TV/VCR combo code in
release SET.
the below boxes:
3. Enter 9 - 7 - 9. The LED will blink twice.
4. Select a device. For this example, press VCR once. Then assign Now when you press MACRO once, the TV will turn on and tune to
a desired Control Group to the device. For this example, press channel 03. Then the cable box will turn on and tune to channel 11.
PLAY once, which will assign the entire group of Transport
Clearing A Macro
Controls (i.e., PLAY, STOP, FWD, REW, PAUSE, and REC) to the
1. Press and hold SET until the LED (red light) blinks twice, then
VCR. The LED will blink once.
release SET.
Select another device. For this example, press TV once. Then
5.
2. Enter 9 - 9 - 5. The LED will blink twice.
assign a desired Control Group to this device. For this
example, press VOL+ once, which will assign the entire group
3. Press MACRO once.
of Volume Controls (i.e., VOL+, VOL-, and MUTE) to the TV. The
LED will blink once. 4. Press and hold SET until the LED blinks twice, then release SET.
6. Select another device. For this example, press CBL once. Then
assign a desired Control Group to this device. For this
example, press CH+ once, which will assign the entire group of
USING CHANNEL SCAN
Channel Controls (i.e., CH+, CH-, (Keypad) 0 ~ 9, ENTER, LAST,
SLEEP, INFO, and TV/VCR) to the Cable Box. The LED will blink
In the TV, VCR, DVD, SAT, and CBL modes, use the FAV key to start a
once.
3-second scan of all favorite channels (if programmed – see
7. To add additional Menu functionality to the Cable Box, press Programming Favorite Channel Scan below) and/or all channels for the
CBL once. Then press MENU once. This action will assign the selected mode.
entire group of Menu Controls (i.e., MENU, GUIDE, Cursor
1. If Favorite Channel Scan has been set up, skip to step 2. Otherwise,
Controls (Up, Down, Left, Right), SELECT, and EXIT) to the
press TV, VCR, DVD, SAT, or CBL once.
Cable Box. The LED will blink once.
8. To add PIP functionality to the TV, press TV once. Then press
PIP once. This action will assign the entire group of PIP
Controls (i.e., PIP, MOVE, and SWAP) to the TV. The LED will
blink once.
2. Press FAV once.
9. To exit Home Theater , press and release the SET key. The LED
(red light) blinks twice.
Operating The Home Theater Mode • If Favorite Channel Scan has been set up, scanning of favorite
channels will start and, upon completion, continue to scan all
After programming the Home Theater key (see the previous section), you
channels upward for the same device.
simply activate this mode by pressing HOME THEATER once. Instantly,
groups of remote control keys will be assigned to their • If Favorite Channel Scan has not been set up, scanning will start
programmed devices. with the current channel, then proceed to the next channel up, and
continue until all channels of the selected device is scanned.
For the above example, pressing HOME THEATER once would assign the fol-
lowing keys to the VCR, TV, and Cable Box: 3. To stop scanning channels at any time, press any key once (except the
backlight key ).
VCR: PLAY, STOP, FWD, REW, PAUSE, and REC
TV: VOL+, VOL-, MUTE, PIP, MOVE, and SWAP
PROGRAMMING FAVORITE CHANNEL SCAN
CH+, CH-, (Keypad) 0 ~ 9, ENTER, LAST,
Cable Box:
SLEEP, INFO, TV/VCR, MENU, GUIDE,
In the TV, VCR, DVD, SAT, or CBL mode, you can store a list of up to
Cursor Controls (Up, Down, Left, Right),
10 favorite channels, in any order, that will be immediately scanned when
SELECT, and EXIT
FAV is pressed (see Using Channel Scan).
NOTE: Only channels of one mode can be stored for Favorite Channel Scan.
USING A MACRO
1. On the remote control, press TV, VCR, DVD, SAT, or CBL once.
With programming, the MACRO key on your One For All 8 Device Home
Theater Universal Remote Control can be setup to
perform a repetitive, time-consuming operation for easy, convenient
access through the press of a single key.
A macro can be used to control a home theater operation, to set a favorite
2. Press and hold SET until the LED (red light) blinks twice, then
channel, or for other multiple functions you would like to
release SET.
control with one key press (see examples below). Moreover, the MACRO key
can hold up to 15 key presses total. 3. Enter 9 - 9 - 6. The LED will blink twice.
4. Use the keypad to enter a favorite channel number (e.g., 031).
NOTE: Programming a new macro over an existing one will erase the
Then press SET once.
original macro.
NOTE: If the original remote control required pressing an
Example – Programming A Favorite Channel
the channel, also press the Enter key after the channel number (e.g., 0 - 3 - 1 -
With so many channels available through your cable or satellite Enter ).
system provider, you can program a macro that directly selects a favorite
5. If desired, repeat step 4 (in this section) for each favorite channel to be
channel with one key press.
stored, up to a total of 10 channels.
For example, let's assume your favorite cable programs are on
NOTE: If you try entering more than 10 channels, the remote control will auto-
channel 71. Use the following instructions to program a macro for direct
matically exit programming.
access of this channel:
6. To exit programming, press and hold SET for 3 seconds. The
NOTE: This example assumes the TV tuner is connected directly to the cable line and
LED will blink twice.
not through a cable box.
1. Press and hold SET until the LED (red light) blinks twice, then
USING KEYMOVER
release SET.
The One For All 8 Device Home Theater Universal Remote Control
2. Enter 9 - 9 - 5. The LED will blink twice.
includes a Keymover feature that allows you to map (or copy) keys from
3. Press MACRO once.
one mode (i.e., source mode) to another mode (i.e., destination mode).
4. Press TV once.
NOTE: The following keys cannot be used as a source or destination: TV , VCR , DVD ,
AUX , SAT , HOME THEATER , CD , CBL , RCVR/AMP , and SET .
5. Enter the channel number, 7 - 1.
Programming Keymover
NOTE: If you have access to over 100 channels, enter 0 - 7 - 1 . Moreover,
if the original remote control required pressing an Enter key to change
For example, if your VCR does not have volume control, you can
the channel, also press the Enter key after the channel number (e.g.,
map the volume and mute keys from the TV mode to the VCR mode as fol-
0 - 7 - 1 - Enter ).
lows:
Press and hold SET until the LED blinks twice, then release SET.
6.
1. Press and hold SET until the LED (red light) blinks twice, then
Now when you press MACRO, you will instantly see cable channel 71 on
release SET.
your TV set.
2. Enter 9 - 9 - 4. The LED will blink twice.
Example – Programming A Master Power Key With Instant
Channel Selection
For the source mode, press TV once.
3.
A macro can be programmed to turn on and off your equipment as well.
For example, let's set up a sequence that will turn on the TV and tune it to 4. For the source key, press VOL+ once.
channel 3, and then turn on the Cable Box and tune it to a premium
channel (e.g., 11).
NOTE: This example assumes all equipment is turned off and that the TV is connect-
5. For the destination mode, press VCR once.
ed through the cable box with TV tuning set to channel 3.
6. For the destination key, press VOL + once.
1. Press and hold SET until the LED (red light) blinks twice, then
release SET.
2. Enter 9 - 9 - 5. The LED will blink twice.
7. The LED will blink twice indicating the keymoved sequence
3. Press MACRO once.
is correct.
4. Enter the following sequence:
8. Repeat steps 1 through 7 twice more, substituting VOL– and MUTE as
TV, POWER, and 0 - 3 (or 0 -0 - 3 if access is over 100 channels)
source and destination keys in steps 4 and 6.
Enter
NOTE: If the original remote control required pressing an key to change
Upon completion of the above procedure, you can now use your
the channel, also press the Enter key after the channel number (e.g., 0 - 7 - 1 -
One For All 8 Device Home Theater Universal Remote Control to control
Enter ).
the TV's volume and mute in the VCR mode, as well as in the TV mode.
5. Then enter the following sequence:
CBL, POWER, and 1-1 (or 0 -1- 1 if access is over 100 channels)
6. Press and hold SET until the LED blinks twice, then release SET.
Restoring Keymoved Keys to Default Settings Unlocking All Volume Control (Restoring Default Setting):
Restoring A Single Keymoved Key NOTE: Performing these instructions will restore independent volume control for all
programmed devices (e.g., TV volume control in TV mode, VCR volume in VCR mode,
1. Press a device key that has a keymoved key.
etc.).
2. Press and hold SET until the LED (red light) blinks twice, then
1. On the remote control, press and hold SET until the LED (red
release SET.
light) blinks twice, then release SET.
3. Enter 9 - 9 - 4. The LED will blink twice.
2. Enter 9 - 9 - 3 and then press VOL+ once. The LED will blink
4. Press the destination key twice (where the keymoved key is stored). four times.
The LED will blink twice.
3. Volume will again be independently controlled according to its default
Restoring All Keymoved Keys In A Single Mode states for all programmed devices.
ABOUT UPGRADING
1. Press and hold SET until the LED (red light) blinks twice, then
release SET.
The One For All 8 Device Home Theater Universal Remote Control has
2. Enter 9 - 9 - 4. The LED will blink twice. the largest infrared code library available. However, if you purchase a
brand new home entertainment or home automation device, it may not
3. Press the destination mode twice (where keymoved keys are stored).
respond to the codes stored in the remote control's memory.
The LED will blink twice.
If this happens, please contact our Customer Support department
(see Troubleshooting Section below) to upgrade the remote control. The
RE-ASSIGNING DEVICE KEYS
Customer Support representative will search our entire database for a
code that matches your device and instruct you how to enter it into your
The One For All 8 Device Home Theater Universal Remote Control can be
One For All 8 Device Home Theater Universal Remote Control.
set to control a second TV,VCR, DVD player, or other device.
If the code for your home entertainment or home automation device
For example, to control a TV, a cable box, and two VCRs, you will need to
is not in our database,we will need to "capture" the code for that device
re-assign the unused AUX key to operate the second VCR
from its original remote control. A new code would then be
as follows:
created and entered into your One For All 8 Device Home Theater Universal
Remote Control.If necessary,the Customer Support representative can
1. On the remote control, press and hold SET until the LED (red
instruct you how to begin the capture procedure.
light) blinks twice, then release SET.
Enter 9 - 9 - 2. The LED will blink twice. NOTE: One For All reserves the right to replace a returned remote control with a new
2.
one of equal or superior functionality.
3. Press VCR once, then press AVX once.
Upgrade Exclusions
• Home entertainment or home automation devices controlled by radio
frequency (RF/UHF), wired, or ultrasonic remote controls. Only
devices controlled by infrared remote controls are covered.
• Home entertainment or home automation devices not controlled by
4. The AUX key is now ready to be programmed for your second VCR.
remote controls.
(See Setting Up Your Components.)
• Broken or defective product.
To re-assign other device keys to the AUX key, repeat steps 1 through 4
above by substituting the sequence from the below chart:
• Products that operate over 100 kHz.
To Re-Assign Device Key Perform Sequence
• Infrared keyboards and infrared pointing devices (such as mouse
substitutes).
AUX as 2nd TV key: SET - 9 - 9 - 2 - TV - AUX
AUX as 2nd DVD key: SET - 9 - 9 - 2 -DVD- AUX
• All products for sale and/or use outside the continental United States,
AUX as 2nd SAT key: SET - 9 - 9 - 2 -SAT- AUX
Hawaii,Alaska, or Canada.
AUX as 2nd CD key: SET - 9 - 9 - 2 -CD- AUX
AUX as 2nd CBL key: SET - 9 - 9 - 2 -CBL- AUX
AUX as 2nd RCVR/AMP key: SET - 9 - 9 - 2 - RCVR/AMP - AUX
TROUBLESHOOTING
You can also re-sassign another unused device key by substituting an open
key for the AUX key in the above chart and performing the sequence. For
PROBLEM:
example, to re-assign an unused SAT key as a 2nd CD key, perform SET - 9
SOLUTION: Replace batteries with two new AA alkaline batteries.
- 9 - 2 -CD- SAT.
When a re-assignment is done, the LED (red light) will blink twice to con- PROBLEM:
firm your choice.At that time, you will need to program the remote control
for the new device (see Setting Up Your Components).
SOLUTION: Make sure the remote control is aimed at your home
Enter key to change
CHANGING VOLUME LOCK PROBLEM:
The One For All 8 Device Home Theater Universal Remote Control is set
SOLUTION: Try all listed codes for the device brands being set up.
at the factory for independent volume control of each selected device.
However, you may change the Volume Lock setting to Global Volume Lock
so that a device's volume will be locked to one mode (e.g., to control TV
volume in all other modes).After that, if desired, you can perform
PROBLEM:
Individual Volume Unlock on a selected device to set its volume control for
SOLUTION: Use the VCR codes for your brand. Some combo units may
independent operation.
Locking Volume Control To One Mode (Global Volume Lock):
PROBLEM:
1. Press and hold SET until the LED (red light) blinks twice, then
release SET. SOLUTION: If original remote control required pressing ENTER to
2. Enter 9 - 9 - 3 and then press any mode key once (e.g., TV).
The LED will blink twice.
PROBLEM:
3. Now, when you press VOL+, VOL–, or MUTE, the vol-
ume of the selected device (e.g., TV) will be controlled
SOLUTION: Clear the device key as follows: Press and hold SET until the
regardless of the mode you have selected.
PROBLEM:
SOLUTION: For power on, these products require programming TV
Unlocking Volume Control For A Single Device (Individual
Volume Unlock):
1. Press a desired mode key where you want volume to be PROBLEM:
unlocked (e.g., RCVR/AMP) and controlled within its own
SOLUTION: Due to RCA design (1983-1987), only the original remote
mode.
2. After performing Global Volume Lock (above), press and hold
PROBLEM:
SET again until the LED (red light) blinks twice, then release
SET.
SOLUTION: See Changing Volume Lock to lock/unlock volume.
3. Enter 9 - 9 - 3 and then press VOL– once. The LED will blink
PROBLEM:
four times.
SOLUTION: Please contact us in any of the following ways:
4. If desired, repeat steps 1 through 3 (of this section) for each device
that you want volume to be unlocked.
5. Now, after you select a device that has volume
unlocked (e.g., RCVR/AMP), pressing VOL+, VOL–, or
MUTE, will control the device's volume only in its own
mode.
LED (red light) does not blink when you press a key.
LED blinks when you press a key, but home
entertainment device does not respond.
entertainment device and is not farther than 15 feet away.
The unit does not control home entertainment devices or
commands are not working properly.
Make sure they can be operated with an infrared remote
control.
TV/VCR combo does not respond properly.
require both a TV code and a VCR code for full operation.
Changing channels does not work properly.
change channels, press ENTER on the remote control after
entering the channel number.
Tried Search For Your Code method and still could not find
a working code.
LED (red light) blinks twice, then release. Next enter
9 - 9 - 2. Then press the device key to be cleared twice. Now
repeat the Search For Your Code method.
Remote control does not turn on Sony or Sharp TV/VCR
Combo.
codes. For Sony, use TV code 0000 and VCR code 0032. For
Sharp, use TV code 0093 and VCR code 0048.
CH+ and CH- do not work for your RCA TV.
control will operate these functions.
No remote control of volume.
If the above does not work.
• Please visit :www.oneforall.com
• If the above website is not able to provide you
with the information you need, please email us at
ofasupport@ueic.com and refer to "Troubleshooting"
• Customer Support : (330) 405-8615