One for All URC-8811 User Manual

Press MUTE once to turn the sound off
or on.
In TV, VCR, DVD, SAT, and CBL modes, use
FAV to scan favorite channels and/or all
8L DEVICE HOME THEATER
channels. See Using Channel Scan and
Programming Favorite Channel Scan.
UNIVERSAL REMOTE CONTROL
Use CH+ (or CH-) to select the next higher
WITH LEARNING
(or lower) channel.
Press PREV once to recall the last-viewed
channel and to page back one screen on
the main menu.
In the CD mode, use PREV to turn random
play on or off.
In the RCVR/AMP mode, use PREV to select
the receiver band.
Use the keypad (1 ~ 9 and 0) to directly
select channels (for example, 009 or 031).
In the RCVR/AMP mode, use the keypad
(1 ~ 9 and 0) to select audio sources 1
through 10.
Press ENTER once after entering the
channel numbers on some TVs.
In the CD mode, use ENTER to add 10 to
the digit entry (e.g., ENTER and 7 is 17).
Use TV/VID to switch the TV's input to
view TV or video programs.
Use the transport keys to control your
VCR, DVD or CD player, or VOD (Video
On Demand) if available on your cable or
satellite service.
To record a VCR program, press REC twice.
After programming, press M1~ M4 once to
run a desired macro (see Using Macros).
USER'S GUIDE
After programming, press L1~ L4 once
to activate a learned function (see
Using Learning Keys).
INTRODUCTION
Use PIP to switch the Picture-In-Picture
The One For All 8L Home Theater Upgradeable Universal Remote
feature on or off (if available on your TV).
Control with Learning (URC-8811) is designed to operate up to
Use MOVE to move the window picture
eight home entertainment devices, including TV, video, and audio
to different positions in the main picture.
components. The remote control requires four (4) fresh AAA alka-
line batteries (not included) and easy programming to control your
Use SWAP to switch images and sound
devices. For best results, please read and perform all instructions
between the main and window pictures.
listed here.Also, keep these instructions for future reference.
Press SLEEP to activate your device's sleep
timer (not available for all devices).
Use to turn on or off the key backlight.
FEATURES AND FUNCTIONS
When this feature is activated, keys will
remain backlight for 5 seconds after the
Use the Key Charts (below) to learn how to use the universal features
last key press.
and functions of the One For All 8L Home Theater Upgradeable
Universal Remote Control with Learning (URC-8811).
Use SET for all programming sequences.
Key Charts
The LED (red light) blinks to show that
the remote control is working and is
sending signals.
INSTALLING BATTERIES
` Press TV, VCR, DVD, AUX, SAT, CD, CBL, or
RCVR/AMP once to select a desired home
1. On the remote control's back, push the tab and lift off the
entertainment device to control.
battery cover.
After programming, press HOME THEATER
2. Obtain four (4) new (fully-charged) AAA alkaline batteries.
once to select the home theater mode (see Match the + and – marks on the batteries to the + and – marks
Using The Home Theater Mode).
in the battery case, then insert the new batteries.
3. Press the battery cover back into place. The tab should click
Press POWER once to turn on or off the
selected device. when the cover is locked.
4. Test the remote control by first pressing POWER and then any
Press MENU once to display your selected
mode key (e.g., TV). If batteries are inserted correctly, the LED
device's main menu.
(red light) will blink once.
Use GUIDE to display your selected
NOTE: When batteries need replacement, the remote control will stop
device's program guide or setup menu. operating. Remove the old batteries and insert new ones to ensure all of
your programming information is restored.
Use EXIT to exit from your selected
device's guide or menu.
PROGRAMMING DEVICE CONTROL
Use INFO to display the current channel
and program information.
The One For All 8L Home Theater Upgradeable Universal Remote
Control with Learning is preprogrammed at the factory to operate
Use the cursor keys to move the cursor in
an RCA TV and VCR, a Motorola (GI) cable box, an RCA satellite
the program guide and menu screens.
receiver, a Pioneer CD player, a Toshiba DVD player, a Pioneer audio
Use SELECT to choose options from your
receiver/ amplifier, and a One For All home automation device. To
selected device's menu or guide.
control devices other than the default brands, perform the following
In the CD mode, use SELECT to select a steps; otherwise skip this section:
compact disc. Use (or ) to select the
NOTE: For TV/VCR Combo control, see the next section.
next (or previous) CD. Use (or ) to
1. Turn on a device (e.g.,VCR or DVD player) and, if applicable,
select the next (or previous) track.
insert media (e.g., cassette or disc).
In the RCVR/AMP mode, use SELECT to
NOTE: Please read steps 2 through 4 completely before proceeding.
set the surround sound. Use (or )
Highlight or write down the codes and device you wish to program before
to adjust the volume higher (or lower).
starting step 2.
Use (or ) to adjust the balance left
(or right). 2. On the remote control, press a device key once (i.e., TV, VCR, DVD,
AUX, SAT, CD, CBL, or RCVR/AMP).
Use VOL+ (or VOL-) to raise (or lower) the
sound volume. NOTE: Use the AUX key to program control of home automation devices as
well as miscellaneous audio services and video accessories. Alternately, use
the AUX key to program control of a second device type (e.g., a second VCR;
see "Re-assigning Device Keys").
3. Press and hold SET until the LED (red light) blinks twice, then CHECKING THE CODES
release SET.
If you have set up the remote control using the Searching For Your
4. Use the Manufacturer's Codes (on the back) to locate the type of Code procedure, you may need to find out which four-digit code is
device and brand name and then enter the first four-digit code operating your equipment. For example, to find out which code is
operating your TV:
for your device. If performed correctly, the LED will blink twice.
NOTE: If the LED did not blink twice, repeat steps 2 through 4 and try 1. On the remote control, press TV once.
entering the same code again.
2. Press and hold SET until the LED (red light) blinks twice, then
release SET.
5. Aim the remote control at the device and press POWER once. The
device should turn off. If it does not respond, repeat steps 2
3. Enter 9 - 9 - 0. The LED will blink twice.
through 5, trying each code for your brand until you find one that
4. To view the code for the first digit, press 1 once.Wait 3 seconds,
works. If it still does not work, try Searching For Your Code.
count the LED blinks (e.g., three blinks = 3) and write down
NOTE: If the device does not have a POWER key, press the ( Play ) key. the number.
6. Repeat steps 1 through 5 for each device you want to control. NOTE: If a code digit is "0", the LED will not blink.
For future reference, write down each working device code in the
5. Repeat step 4 three more times for remaining digits. Use 2 for the
boxes below:
second digit, 3 for the third digit, and 4 for the fourth digit.
TV Code: 6. To check for codes of other devices, repeat steps 1 through 5,
but substitute the appropriate device key for each device you
are checking.
VCR Code:
USING THE HOME THEATER MODE
The One For All 8L Home Theater Upgradeable Universal Remote
DVD Code:
Control with Learning includes a custom Home Theater mode.
After the HOME THEATER key is programmed, it will allow you to
SAT Code: access five groups of remote control keys without having to change
device modes.
Control Organization
CD Code:
About Control Groups
CBL Code: For Home Theater programming, the remote control's keys are
grouped by type of control into the following five control groups:
(1) Transport Controls: PLAY, STOP, FWD, REW, PAUSE, and REC
RCVR/AMP Code:
(2) Volume Controls: VOL+, VOL-, and MUTE
AUX Code:
(3) Channel Controls: CH+, CH-, (Keypad) 0 ~ 9, ENTER, LAST,
SLEEP, INFO, and TV/VCR
Aux. Device Type: _______________________________
(4) Menu Controls: MENU, GUIDE, Cursor Controls (Up, Down,
Left, Right), SELECT, and EXIT
(5) PIP Controls: PIP, MOVE, and SWAP
About Device Groups
PROGRAMMING TV/VCR COMBO CONTROL
Moreover, the remote control's devices are grouped into the following
Perform the following instructions to control a TV/VCR Combo:
five device groups:
1. Turn on the TV/VCR Combo and insert a video cassette.
(1) Device Group 1: VCR, DVD, CD, and RCVR/AMP
NOTE: Please read steps 2 through 4 completely before proceeding. (2) Device Group 2: TV, VCR, CBL, SAT, CD, and RCVR/AMP
Highlight or write down the codes and device you wish to program before
(3) Device Group 3: TV, VCR, CBL, SAT, CD, and RCVR/AMP
starting step 2.
(4) Device Group 4: TV, VCR, CBL, SAT, and DVD
2. On the remote control, press VCR.
(5) Device Group 5: TV
3. Press and hold SET until the LED (red light) blinks twice, then
release SET. The default Device Group setting from the factory is:
4. Use the Setup Codes For TV/VCR Combos (on the back) to locate (1) Device Group 1: VCR
the brand name and then enter the first four-digit code for your
(2) Device Group 2: TV
device. If performed correctly, the LED will blink twice.
(3) Device Group 3: CBL
NOTE: If the LED did not blink twice, repeat steps 2 through 4 and try
(4) Device Group 4: CBL
entering the same code again.
(5) Device Group 5: TV
5. Aim the remote control at the device and press POWER once. It
should turn off. If the device does not respond, repeat steps 2 Programming The Home Theater Mode
through 5, trying each code for your brand until you find one that
For example, let's assume you have a TV, a cable box, and a VCR in
works. If it still does not work, try Searching For Your Code.
your home theater system.You can set up the Home Theater mode
so that selected controls are assigned to these devices as follows:
NOTE: If the device does not have a POWER key, press the ( Play ) key.
1. On the remote control, press HOME THEATER.
6. If you've located a setup code that works, but it has a separate TV
code, you'll also need to program it into the remote control to
2. Press and hold SET until the LED (red light) blinks twice, then
access volume control as follows: release SET.
a. Press TV once. The LED (red light) will blink twice. 3. Enter 9 - 7 - 9. The LED will blink twice.
4. Select a device. For this example, press VCR once. Then assign a
b. Enter the TV code for your TV/VCR Combo. If correct, the
desired Control Group to the device. For this example, press PLAY
LED will blink twice.
once, which will assign the entire group of Transport Controls
NOTE: For VCR/TV Combos programmed with separate TV codes, (i.e., PLAY, STOP, FWD, REW, PAUSE, and REC) to the VCR. The LED
TV volume is controlled by pressing VCR first and then TV . After that, use will blink once.
VOL+ (or VOL- ) to raise (or lower) the TV volume. For other alternatives on
5. Select another device. For this example, press TV once. Then
controlling your volume keys, see the "Changing Volume Lock" or "Using
assign a desired Control Group to this device. For this example,
Keymover" sections.
press VOL+ once, which will assign the entire group of Volume
7. For future reference, write down the working TV/VCR combo Controls (i.e., VOL+, VOL-, and MUTE) to the TV. The LED will
code in the below boxes: blink once.
6. Select another device. For this example, press CBL once. Then
TV/VCR Code:
assign a desired Control Group to this device. For this example,
press CH+ once, which will assign the entire group of Channel
TV Code (if used): Controls (i.e., CH+, CH-, (Keypad) 0 ~ 9, ENTER, LAST, SLEEP,
INFO, and TV/VCR) to the Cable Box. The LED will blink once.
7. To add additional Menu functionality to the Cable Box, press CBL
once. Then press MENU once. This action will assign the entire
group of Menu Controls (i.e., MENU, GUIDE, Cursor Controls (Up,
SEARCHING FOR YOUR CODE
Down, Left, Right), SELECT, and EXIT) to the Cable Box. The LED
will blink once.
If your device does not respond to the remote control after trying all
codes listed for your brand, or if your brand is not listed at all, try 8. To add PIP functionality to the TV, press TV once. Then press PIP
searching for your code. once. This action will assign the entire group of PIP Controls (i.e.,
PIP, MOVE, and SWAP) to the TV. The LED will blink once.
For example, to search for a code for your TV:
9. To exit Home Theater programming, press and hold SET until the
1. On the remote control, press TV once.
LED (red light) blinks twice, then release SET.
2. Press and hold SET until the LED (red light) blinks twice, then Operating The Home Theater Mode
release SET.
After programming the Home Theater key (see previous), you simply
3. Enter 9 - 9 - 1. The LED will blink twice. activate this mode by pressing HOME THEATER once. Instantly, groups
of remote control keys will be assigned to their programmed devices.
4. Aim the remote control at the the TV and slowly alternate
For the above example, pressing HOME THEATER once would assign
between pressing POWER and TV. Stop when the TV turns off.
the following keys to the VCR, TV, and Cable Box:
NOTE: In the search mode, the remote control will send IR codes from its
VCR: PLAY, STOP, FWD, REW, PAUSE, and REC
library to the selected device, starting with the most popular code first.
TV: VOL+, VOL-, MUTE, PIP, MOVE, and SWAP
5. To lock in the code, press and hold SET until the LED blinks
twice, then release SET. Cable Box: CH+, CH-, (Keypad) 0 ~ 9, ENTER, LAST,
SLEEP, INFO, TV/VCR, MENU, GUIDE,
6. To search for the codes of your other devices, repeat steps 1
Cursor Controls (Up, Down, Left, Right),
through 5, but substitute the appropriate device key for the
SELECT, and EXIT
device you are searching for.
USING MACROS
With programming, the M1 through M4 keys on your One For All 8L
Home Theater Upgradeable Universal Remote Control with Learning
can be setup to perform repetitive, time-consuming operations for
easy, convenient access through the press of a single key.
Macro keys are ideal for home theater operations, setting a favorite learning. Be sure to press each key within 10 seconds of the previous entry. If
channel, guide steps, or other multiple functions you would like to not, the remote control will exit the programming mode.
control with one key press. Moreover, each macro key can hold up
Programming A Learning Key
to15 key presses total.
1. Press and hold SET until the LED (red light) blinks twice, then
NOTE: Programming a new macro over an existing one will erase the
release SET.
original macro.
2. Enter 9 - 7 - 5. The LED will blink twice.
Programming A Favorite Channel
3. Press a device key once (e.g., TV) to assign a mode for learning.
With so many channels available through your cable or satellite
system provider, you can program a macro that directly selects a 4. Press an open learning key once (e.g., L1) to store a feature to be
favorite channel with one key press. learned. The LED will blink rapidly for 4 seconds. If the LED does
not blink rapidly, go back to step 1 and start again.
For example, let's assume your favorite cable programs are on
channel 71. Use the following instructions to program a macro key 5. Place your original remote control (e.g., TV remote control)
for direct access of this channel: head-to-head (about 2" apart) from the One For All 8L Home
Theater Upgradeable Universal Remote Control with Learning.
NOTE: This example assumes the TV tuner is connected directly to the cable
line and not through a cable box. 6. On your original remote control, press and hold the key (i.e., fea-
ture) to be learned until the LED on the One For All 8L Universal
1. Press and hold SET until the LED (red light) blinks twice, then
Remote Control blinks twice. If the LED does not blink twice,
release SET.
repeat steps 3 through 6.
2. Enter 9 - 9 - 5. The LED will blink twice.
7. To learn functions onto other learning keys (e.g., L2 ~ L4), repeat
steps 3 through 6.
3. Select an open macro key (e.g., M1) and press it once.
4. Press TV once. 8. To lock in new feature(s) on the One For All 8L Universal Remote
Control, press and hold SET until the LED blinks twice, then
5. Enter the channel number, 7 - 1.
release SET.
NOTE: If you have access to over 100 channels, enter 0 - 7 - 1 . Moreover,
9. To test a learned feature, press a device key (e.g., TV) once where
if the original remote control required pressing an Enter key to change
the learning mode was assigned. Then press the learning key
the channel, also press the Enter key after the channel number (e.g.,
(e.g., L1) where the learned feature is stored.
0 - 7 - 1 - Enter ).
Deleting Functions From The Learning Keys:
6. Press and hold SET until the LED blinks twice, then release SET.
1. Press and hold SET until the LED (red light) blinks twice, then
Now when you press M1, you will instantly see cable channel 71 on
release SET.
your TV set.
2. Enter 9 - 7 - 6. The LED will blink twice.
Programming A Master Power Key With Instant Channel
Selection 3. Press the device key once where the learned feature is stored
(e.g., TV).
A macro key can be programmed to turn on and off your equipment
as well. For example, let's set up a sequence that will turn on the TV 4. Press the learning key (e.g., L1) to be deleted twice. The LED will
blink twice after the second press.
and tune it to channel 3, and then turn on the Cable Box and tune it
to a premium channel (e.g., 11).
5. To clear additional functions stored on other learning keys,
repeat steps 1 through 4 (in this section).
NOTE: This example assumes all equipment is turned off and that the TV is
connected through the cable box with TV tuning set to channel 3.
RE-ASSIGNING DEVICE KEYS
1. Press and hold SET until the LED (red light) blinks twice, then
The One For All 8L Home Theater Upgradeable Universal Remote
release SET.
Control with Learning can be set to control a second TV,VCR, DVD
2. Enter 9 - 9 - 5. The LED will blink twice.
player, or other device. For example, to control a TV, a cable box, and
two VCRs, you will need to re-assign the unused AUX key to operate
3. Select an open macro key (e.g., M2) and press it once.
the second VCR as follows:
4. Enter the following sequence:
1. On the remote control, press and hold SET until the LED (red
TV, POWER, and 0 - 3 (or 0 -0 - 3 if access is over 100 channels) light) blinks twice, then release SET.
Enter 2. Enter 9 - 9 - 2. The LED will blink twice.
NOTE: If the original remote control required pressing an key to
change the channel, also press the Enter key after the channel number (e.g.,
3. Press VCR once, then press AUX once.
0 - 7 - 1 - Enter ).
4. The AUX key is now ready to be programmed for your second
5. Then enter the following sequence:
VCR. See Programming Device Control.
CBL, POWER, and 1-1 (or 0 -1- 1 if access is over 100 channels)
To re-assign other device keys to the AUX key, repeat steps 1 through 4
6. Press and hold SET until the LED blinks twice, then release SET. above by substituting the sequence from the below chart:
Now when you press M2 once, the TV will turn on and tune to To Re-Assign Device Key Perform Sequence
channel 03. Then the cable box will turn on and tune to channel 11.
AUX as 2nd TV key: SET - 9 - 9 - 2 - TV - AUX
Clearing A Macro AUX as 2nd DVD key: SET - 9 - 9 - 2 -DVD- AUX
AUX as 2nd SAT key: SET - 9 - 9 - 2 -SAT- AUX
1. Press and hold SET until the LED (red light) blinks twice, then
AUX as 2nd CD key: SET - 9 - 9 - 2 -CD- AUX
release SET.
AUX as 2nd CBL key: SET - 9 - 9 - 2 -CBL- AUX
AUX as 2nd RCVR/AMP key: SET - 9 - 9 - 2 - RCVR/AMP - AUX
2. Enter 9 - 9 - 5. The LED will blink twice.
3. Select a macro key (e.g., M1~M4) you want to clear and press
You can also re-sassign another unused device key by substituting an
it once.
open key for the AUX key in the above chart and performing the
sequence. For example, to re-assign an unused SAT key as a 2nd CD
4. Press and hold SET until the LED blinks twice, then release SET.
key, perform SET - 9 - 9 - 2 -CD- SAT. When a re-assignment is done,
USING CHANNEL SCAN
the LED (red light) will blink twice to confirm your choice.At that
time, you will need to program the remote control for the new device
In the TV, VCR, DVD, SAT, and CBL modes, use the FAV key to start a
(see Programming Device Control).
3-second scan of all favorite channels (if programmed – see
USING KEYMOVER
Programming Favorite Channel Scan below) and/or all channels for
the selected mode.
The One For All 8L Home Theater Upgradeable Universal Remote
1. If Favorite Channel Scan has been set up, skip to step 2.
Control with Learning includes a Keymover feature that allows you
Otherwise, press TV, VCR, DVD, SAT, or CBL once.
to map (or copy) keys from one mode (i.e., source mode) to another
mode (i.e., destination mode).
2. Press FAV once.
NOTE: The following keys cannot be used as a source or destination: TV , VCR ,
• If Favorite Channel Scan has been set up, scanning of favorite
DVD , AUX , SAT , HOME THEATER , CD , CBL , RCVR/AMP , and SET .
channels will start and, upon completion, continue to scan all
channels upward for the same device. Programming Keymover
• If Favorite Channel Scan has not been set up, scanning will For example, if your VCR does not have volume control, you can
start with the current channel, then proceed to the next map the volume and mute keys from the TV mode to the VCR mode
channel up, and continue until all channels of the selected as follows:
device is scanned.
1. Press and hold SET until the LED (red light) blinks twice, then
3. To stop scanning channels at any time, press any key once
release SET.
(except the backlight key ).
2. Enter 9 - 9 - 4. The LED will blink twice.
PROGRAMMING FAVORITE CHANNEL SCAN
3. For the source mode, press TV once.
In the TV, VCR, DVD, SAT, or CBL mode, you can store a list of up to
4. For the source key, press VOL+ once.
10 favorite channels, in any order, that will be immediately scanned
when FAV is pressed (see Using Channel Scan).
5. For the destination mode, press VCR once.
NOTE: Only channels of one mode can be stored for Favorite Channel Scan. 6. For the destination key, press VOL + once.
1. On the remote control, press TV, VCR, DVD, SAT, or CBL once. 7. The LED will blink twice indicating the keymoved sequence
is correct.
2. Press and hold SET until the LED (red light) blinks twice, then
release SET. 8. Repeat steps 1 through 7 twice more, substituting VOL– and
MUTE as source and destination keys in steps 4 and 6.
3. Enter 9 - 9 - 6. The LED will blink twice.
Upon completion of the above procedure, you can now use your
4. Use the keypad to enter a favorite channel number (e.g., 031).
One For All 8L Home Theater Upgradeable Universal Remote
Then press SET once.
Control with Learning to control the TV's volume and mute in the
NOTE: If the original remote control required pressing an Enter key to VCR mode, as well as in the TV mode.
change the channel, also press the Enter key after the channel number (e.g.,
Restoring Keymoved Keys to Default Settings
0 - 3 - 1 - Enter ).
Restoring A Single Keymoved Key
5. If desired, repeat step 4 (in this section) for each favorite channel
to be stored, up to a total of 10 channels. 1. Press a device key that has a keymoved key.
NOTE: If you try entering more than 10 channels, the remote control will 2. Press and hold SET until the LED (red light) blinks twice, then
automatically exit programming. release SET.
6. To exit programming, press and hold SET for 3 seconds. The LED 3. Enter 9 - 9 - 4. The LED will blink twice.
will blink twice.
4. Press the destination key twice (where the keymoved key is
USING LEARNING KEYS
stored). The LED will blink twice.
Use the learning keys (L1 ~ L4) to add functions that are unique to Restoring All Keymoved Keys In A Single Mode
your home entertainment devices (e.g.,VCR Tracking Up or Down).
1. Press and hold SET until the LED (red light) blinks twice, then
NOTE: Please have your original remote controls handy before programming release SET.
2. Enter 9 - 9 - 4. The LED will blink twice. set up. Make sure they can be operated with an
infrared remote control.
3. Press the destination mode twice (where keymoved keys are
stored). The LED will blink twice. PROBLEM: TV/VCR combo does not respond properly.
SOLUTION: Use the VCR codes for your brand. Some combo
units may require both a TV code and a VCR code
for full operation.
CHANGING VOLUME LOCK
PROBLEM: Changing channels does not work properly.
The One For All 8L Home Theater Upgradeable Universal Remote
SOLUTION: If original remote control required pressing ENTER
Control with Learning is set at the factory for independent volume
to change channels, press ENTER on the remote
control of each selected device. However, you may change the Volume
control after entering the channel number.
Lock setting to Global Volume Lock so that a device's volume will be
PROBLEM: During learning, LED emits a long blink after pressing
locked to one mode (e.g., to control TV volume in all other modes).
and holding key to be learned.
After that, if desired, you can perform Individual Volume Unlock on a
selected device to set its volume control for independent operation.
SOLUTION: A bad capture has occurred.Avoid high-ambient
Locking Volume Control To One Mode (Global Volume Lock): light sources, such as direct daylight and fluorescent
bulbs. Try readjusting positions of remote controls
1. Press and hold SET until the LED (red light) blinks twice, then
before performing the procedure again.
release SET.
PROBLEM: Tried Search For Your Code method and still could not
2. Enter 9 - 9 - 3 and then press any mode key once (e.g., TV). The
find a working code.
LED will blink twice.
SOLUTION: Clear the device key as follows: Press and hold
3. Now, when you press VOL+, VOL–, or MUTE, the volume of the
SET until the LED (red light) blinks twice, then
selected device (e.g., TV) will be controlled regardless of the
release. Next enter 9 - 9 - 2. Then press the device key
mode you have selected.
to be cleared twice. Now repeat the Search For Your
Unlocking Volume Control For A Single Device (Individual Code method.
Volume Unlock):
PROBLEM: Remote control does not turn on Sony or Sharp
TV/VCR Combo.
1. After performing Global Volume Lock (above), press and hold
SET again until the LED (red light) blinks twice, then release SET.
SOLUTION: For power on, these products require programming
2. Press a desired mode key where you want volume to be unlocked TV codes. For Sony, use TV code 0000 and VCR
(e.g., RCVR/AMP) and controlled within its own mode. code 0032. For Sharp, use TV code 0093 and VCR
code 0048.
3. Enter 9 - 9 - 3 and then press VOL– once. The LED will blink
four times. PROBLEM: CH+ and CH- do not work for your RCA TV.
SOLUTION: Due to RCA design (1983-1987), only the original
4. If desired, repeat steps 1 through 3 (of this section) for each
remote control will operate these functions.
device that you want volume to be unlocked.
PROBLEM: No remote control of volume.
5. Now, after you select a device that has volume unlocked (e.g.,
RCVR/AMP), pressing VOL+, VOL–, or MUTE, will control the
SOLUTION: See Changing Volume Lock to lock/unlock volume.
device's volume only in its own mode.
Unlocking All Volume Control (Restoring Default Setting):
CUSTOMER SUPPORT
NOTE: Performing these instructions will restore independent volume control
for all programmed devices (e.g., TV volume control in TV mode, VCR volume For assistance, please contact us in any of the following ways:
in VCR mode, etc.).
• E-mail: ofasupport@ueic.com
1. On the remote control, press and hold SET until the LED (red
• Internet: http://www.oneforall.com
light) blinks twice, then release SET.
• Consumer Help Line: (330) 405-8616
2. Enter 9 - 9 - 3 and then press VOL+ once. The LED will blink
four times. LIMITED WARRANTY
3. Volume will again be independently controlled according to its
One For All® warrants, to the original purchaser only, that this prod-
default states for all programmed devices.
uct will be free from defects in materials and workmanship, under
ABOUT UPGRADING normal use, for ninety (90) days from the date of original purchase.
The One For All 8L Home Theater Upgradeable Universal Remote
Control with Learning has the largest infrared code library available.
This limited warranty is valid only on ONE FOR ALL® product pur-
However, if you purchase a brand new home entertainment or home
chased and used in the United States of America or Canada, and
automation device, it may not respond to the codes stored in the
does not apply to products used for industrial or commercial pur-
remote control's memory.
pose.
If this happens, please contact our Customer Support department
(see Customer Support below) to upgrade the remote control. The
The limited warranty does not cover damage or failure caused by
Customer Support representative will search our entire database for
products or services not supplied by ONE FOR ALL® , or which
a code that matches your device and instruct you how to enter it into
result from accident, misuse, abuse, neglect, mishandling, misappli-
your One For All 8L Home Theater Upgradeable Universal Remote
cation, faulty installation, set-up adjustment, improper maintenance,
Control with Learning.
alteration, maladjustment of consumer controls, modifications, com-
If the code for your home entertainment or home automation device
mercial use, or that is attributable to acts of God.
is not in our database, we will need to "capture" the code for that
device from its original remote control. A new code would then be
created and entered into your One For All 8L Home Theater
There are no express warranties except as listed above. ONE FOR
Upgradeable Universal Remote Control with Learning. If necessary,
ALL® SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSE-
the Customer Support representative can instruct you how to begin
QUENTIAL DAMAGES RESULTING FROM THE USE OF THIS
the capture procedure.
PRODUCT OR ARISING OUT OF ANY BREACH OF WARRANTY.
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE
NOTE: One For All reserves the right to replace a returned remote control with
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
a new one of equal or superior functionality.
PARTICULAR PURPOSE,ARE LIMITED TO THE WARRANTY
Upgrade Exclusions
PERIOD SET FORTH ABOVE. Some states do not allow the exclusion
or limitation of incidental or consequential damages, or limitations
• Home entertainment or home automation devices controlled by
on how long an implied warranty lasts, so the above exclusions or
radio frequency (RF/UHF), wired, or ultrasonic remote controls.
limitations may not apply to you. This warranty gives you specific
Only devices controlled by infrared remote controls are covered.
legal rights and you may also have other rights which vary from
• Home entertainment or home automation devices not controlled
state to state.
by remote controls.
To obtain warranty service for a defective product during the war-
• Broken or defective product.
ranty period, please return the product, preferably in the original
carton, along with your purchase receipt, to the store of original pur-
• Products that operate over 100 kHz.
chase.A note detailing the complaint would be helpful. The store, at
• Infrared keyboards and infrared pointing devices (such as its option, will replace or repair this product if found to be defective.
mouse substitutes).
• All products for sale and/or use outside the continental United
States, Hawaii,Alaska, or Canada.
ADDITIONAL INFORMATION
TROUBLESHOOTING
As you update your home entertainment system, One For All® has
PROBLEM: If you own a satellite that uses code 0775 (Express Vu
a universal remote control that will fit your needs. Look for these
and Echostar) and your exit key does not work, per-
exciting products at a retailer near you.
form the following sequence to activate this
One For All Access 3 ..............................................................URC-3605
feature/function.
One For All Video Expert 4 Device .......................................URC-4081
SOLUTION: 1. Press the CBL/SAT key
One For All Video Expert Plus 4L .........................................URC-4880
2. Press and hold the SET key until the red LED blinks
One For All Access 4 ..............................................................URC-4605
twice
One For All Access 5 ..............................................................URC-5705
3. Press 9-9-4, the red LED will blink twice
One For All 6 Device Home Theater .....................................URC-6011
4. Press SET and release (one blink on LED)
One For All 8 Device Home Theater .....................................URC-8011
5. Press 3-3-6
One For All 8L Device Home Theater
6. Press the EXIT key, the red LED will blink twice.
with Learning Capability.......................................................URC-8811
The Exit key will now correctly perform the exit fea-
One For All A/V LCD 8 Device With Learning .....................URC-8910
ture/function on your satellite.
One For All IR/RF LCD 8 Device With Learning..................URC-9910
PROBLEM: LED (red light) does not blink when you press a key.
ONE FOR ALL® is the registered trademark of Universal Electronics
Inc. Computime International Ltd. is the Licensee of the ONE FOR
SOLUTION: Replace batteries with four new AAA alkaline batteries.
ALL® brand for USA and Canada.
PROBLEM: LED blinks when you press a key, but home entertain-
Copyright 2002 by Universal Electronics Inc.No part of this publication
ment device does not respond.
may be reproduced,transmitted,transcribed,stored in any retrieval
SOLUTION: Make sure the remote control is aimed at your system,or translated to any language,in any form or by any means,
electronic,mechanical,magnetic,optical,manual,or otherwise,with-
home entertainment device and is not farther
out the prior written permission of Universal Electronics Inc.
than 15 feet away.
The One For All® 6 Device Universal Remote Control is
PROBLEM: The unit does not control home entertainment devices
compatibile for use in North America, excluding Mexico.
or commands are not working properly.
URC-8810w/8811
SOLUTION: Try all listed codes for the device brands being
One For All
(330) 405-8655
02/02