Delta Electronics DVPAETB-ID32A/OR16A Instruction Sheet

Warning
Please read this instruction sheet carefully before use.
DVPAETB series is an OPEN-TYPE device and therefore should be installed in an enclosure free of airborne dust,
humidity, electric shock and vibration. The enclosure should prevent non-maintenance staff from operating the
device (e.g. key or specific tools are required to open the enclosure) in case danger and damage on the device may
occur.
DO NOT connect input AC power supply to any of the I/O terminals; otherwise serious damage may occur.. Check
all the wiring again before switching on the power, and DO NOT touch any terminal when the power is switched
on.
Introduction
DVPAETB-ID32A/OR16A extension drive board is designed for connecting to DVP32SM11N and
DVP32SN11TN, the I/O module with multiple points.
Product Profile & Outline
DVPAETB-ID32A
Unit: mm
1. 40-pin header connector 4. Bottom fastening lock
2. 36-pin input terminal 5. 40-pin IDC connection cable*1
3. DIN rail clip 6. DIN rail
*1: You can select Delta's standard accessory DVPACAB7A10 (IDC 40P-40P 1m)
DVPAETB-OR16A
Unit: mm
1. 2-PIN power input terminal 7. DIN rail clip
2. Power indicator 8. Bottom fastening lock
3. 20-pin header connector 9. 20-pin IDC connection cable*2
4. Output indicator 10. DIN rail
5. Output relay 11. Output point action indicator
6. 9-pin+11-pin output terminal
*2: You can select Delta standard accessory DVPACAB7B10 (IDC 40P-20Px2 1m)
Model Explanation
Input Unit
Model Name Power
Points Type Points
DC Type
DVPAETB-ID32A N/A 32 0
Sink/Source
DVPAETB-OR16A 24V DC 0 N/A 16
Connection Cable
Model Name Length Pins Connector
IDC connector on
DVPACAB7A10 1m 40P-40P DVP32SM11N (DVPAETB-ID32A)
both sides
IDC connector on
DVPACAB7B10 1m 40P-20Px2 DVP32SN11TN (DVPAETB-OR16A)
both sides
Specifications
Electrical Specifications
Model
DVPAETB-ID32A
Item
Insulation resistance > 5M (all I/O point-to-ground: 500V DC)
Operation/storage Operation: 0 ~ 55° C (temperature), 50 ~ 95% (humidity), pollution degree 2
environment
Storage: -25 ~ 70° C (temperature), 5 ~ 95% (humidity)
Weight (g) 166g
Input Point
Type DC (There is no actual input device. Please refer to spec. of DVP32SM11N.)
Input format DC (SINK or SOURCE)
Input voltage/current 24V DC 5mA
Off → On more than 16V DC
Action level
On → Off less than 14.4V DC
Response time Approx. 10ms
Circuit isolation/operation
By internal photocoupler / LED indicators
instruction
Output Point
ENGLISH
Type Relay-R
Current specification 2A/1point (5A/COM)
Voltage specification < 250V AC, 30V DC
75VA (inductive)
Maximum load
90W (resistive)
Response time Approx. 10ms
Installation & Wiring
Terminals of Digital I/O Extension Unit
ID32A
S/S S/S X0 X2 X4 X6 X10 X12 X14 X16 X20 X22 X24 X26 X30 X32 X34 X36
S/S S/S X1 X3 X5 X7 X11 X13 X15 X17 X21 X23 X25 X27 X31 X33 X35 X37
OR16A
Y0 Y1 Y2 Y3 Y4 Y5 Y6 Y7 Y10 Y11 Y12 Y13 Y14 Y15
C0 Y0 Y1 Y2 Y3 C1 Y4 Y5 Y6 Y7 C2 Y10 Y11 Y12 Y13 C3 Y14 Y15
Installation
How to install DIN rail:
Fix one side first.
Next, insert the drive board into the DIN rail and
check if the board is tightly knitted to the rail.
To uninstall the board, push up the board and pull it
out. Follow the steps as indicated in the figure.
Configuration of output points in the connection of DVP32SN11TN and DVPAETB-OR16A:
Output Unit
Type
N/A
Environment Notice:
Relay 250V AC/30V DC
DO NOT install the board in the environment with dust, smoke, metallic debris, corrosive or
2A/1 point, 5A/COM.
flammable gas
DO NO install the board in the premise of high temperature, humidity, direct shock and vibration
DO NOT place the I/O signal wires and power supply wires in the same wiring duct or use cables
Applicable PLC (accessory)
of multiple cores.
Wiring of I/O Points
Wiring of input points:
There are two types of DC inputs, SINK and SOURCE.
DC
(DC Signal IN)
DVPAETB-OR16A
X0
SINK Mode
216g
DC
(DC Signal IN)
X0
SOURCE Mode
Wiring of output points:
Relay output circuit wiring
C0 Y0
5 2
9 3
1. Other output points
2. Fuse
3. Reverse current protection diode*1
4. Manual exclusive output*2
5. Emergency stop: Uses external switch
*1: There is no intermal protection circuit inside the output relay of DVPAETB-OR16A. Therefore, when
activating a DC inductive load, please parallelly connect it to a reverse current protection diode to extend
the life of the contact. The reverse current protection diode shall comply with the following specifications:
a. Able to endure maximum 5 ~ 10 times the amount of the load voltage.
GND +24V
b. Its forward current has to be bigger than the load current.
Y14 Y15
*2: The manual exclusive output uses external circuit and forms an interlock, together with the program
inside the PLC, to ensure safety protection in case of any unexpected errors.
*3: There is no internal protection circuit inside the output relay of DVPAETB-OR16A. Therefore, when
activating an AC inductive load, please parallelly connect it to a varistor (0.1uF + "100ohm to 120ohm") to
Y14 Y15
reduce the interference in the AC load and extend the life of the contact.
Note: Please select proper safety wires. If the wires are not sufficient in long-time operation, overheating and
sparking may occur.
DVPAETB-ID32A/OR16A
產 品 外 觀 及 各 部 介 紹
DVPAETB-ID32A
Wiring Loop
DVPAETB-ID32A POWER SUPPLY
1. 40PIN
2. 36PIN
X35 X36 X37 S/S
+24V GND
3. DIN
*1:
DVPAETB-OR16A
SINK Mode
Wiring Loop
DVPAETB-ID32A POWER SUPPLY
X35 X36 X37 S/S +24V GND
SOURCE Mode
1. 2PIN
2.
3. 20PIN
4.
DVPAETB-OR16A
5.
6. 9PIN+11PIN
Y1 Y2 Y3 C2 Y4 Y5 Y6 Y7
*2:
1
MC2 MC1
2
8 8
配 件 型 號
MC1 MC2
7
7
6
5 4
10
DVPAETB-ID32A
6. Varistor*3
DVPAETB-OR16A
7. Inductive load
8. Incandescent light (resistive load)
連 接 線 型 號
9. DC power supply
10. AC power supply
DVPACAB7A10
DVPACAB7B10
電 氣 規 格
(g)
輸 入 點 規 格
/
繁 體 中 文
(OPEN TYPE) /
/
I/O DVP32SM11N DVP32SN11TN
單 位 ： m m
4.
5. 40PIN IDC *1
6. DIN
DVPACAB7A10 (IDC 40P-40P 1m)
單 位 ： m m
7. DIN
8.
9. 20PIN IDC *2
10. DIN
11.
DVPACAB7B10 (IDC 40P-20Px2 1m)
DC Type
N/A 32 0
Sink/Source
Relay 250V AC/30V DC
24V DC 0 16
2A/1 5A/COM
PIN
1m 40P-40P IDC DVP32SM11N (DVPAETB-ID32A)
1m 40P-20Px2 IDC DVP32SN11TN (DVPAETB-OR16A)
DVPAETB-ID32A DVPAETB-OR16A
5 M 500V DC
0 ~ 55°C 50 ~ 95% 2
-25 ~ 70°C 5 ~ 95%
166g 216g
DVP32SM11N
SINK SOURCE
24V DC 5mA
Off → On 16V DC
On → Off 14.4V DC
10ms
/ LED