Advertisement
BPH1009IUK06EM1.qxd
8/15/06
3:05 PM
Page 7
BEFORE STARTING YOUR PANEL
•
Now please follow the above instructions
HEATER
on how to 'sync' your remote control with
your unit.
Please make sure that feet are properly fixed to
•
If you still encounter operational issues
each end of the unit (see Fig. 2 and assembly
please call: 0800 052 3615
instruction insert). Alternatively you can wall
5. In the event that your remote control does
mount the unit following the below instructions:
notcommunicate- "sync" with your main unit
Wall Mounting
after reading and following the operating
IMPORTANT: Before drilling into any wall
instructions. Please follow the below set-up:
ensure no electrical cables are present in the
• Hold down both mode button on the remote
area.
control and main unit for 5 seconds (the
NOTE: Due to the multitude of potential
power LED will blink once quickly).
mounting surfaces, mounting screws are not
• Release the mode buttons and the main unit
included with this product. Please consult a
will begin to beep.
professional or visit your local hardware store to
• Now please follow above instructions on how
determine which type of screw is best for your
to 'sync' your remote control with your unit.
particular wall.
USE OF GALILEO
1. Remove feet from main unit, if installed.
• The display can show either Fahrenheit or
2. Secure the mounting brackets (Fig. 4B and
Celsius. To change the reading on the remote
3C) to the wall using the dimensions provided
control display, unlock the remote, then turn
in Fig. 4A.
the remote over and push the button located
3. Hang main body on wall brackets installing
on the right hand side, under the stand, with a
first onto bracket "I" , then onto bracket "II".
ball point pen tip. This switch will change the
(See Fig. 4D & 4E)
reading from ºF to ºC and vice versa.
• Whilst using the remote, the backlight function
SETTING UP - FIRST USE ONLY:
will automatically turn on when any button is
1. Put batteries into remote control by removing
pushed and will turn off after 15 seconds of
the battery cover located on the reverse side.
non-use.
Use 3 AAA batteries (Not included) only. DO
• The maximum transmission distance for the
NOT mix alkaline and heavy duty batteries.
remote control is 30 ft. (9 Metres). Do not use
Do not mix old and new batteries.
or position the remote more than 30 ft (9
WARNING: Remove batteries before
Metres) from heater. For accurate temperature
discarding the remote control.
control the remote control must be used in
2. The "ROOM" temperature will be displayed.
same room as heater.
3. Plug heater into mains supply. The power light
• When positioning the remote control, use the
(Red) will illuminate to signal that the unit is in
flip up stand on the reverse side.
stand-by mode.
• Always position the remote control at least 3
4. The first time the unit is plugged in, it will
ft. (1 Metre) from the heater in a convenient
beep every two seconds until it is
position away from draughts or anything that
synchronised with the remote. To synchronise
would influence the room temperature
the unit with the remote control follow the
reading. For example, cold window-sill or
steps below:-
under warm lighting.
• Unlock remote by holding down the "MODE"
• Because heat rises and the remote control
button for 2 seconds until the "LOCK" symbol
senses temperature, the remote control
disappears from the screen. (This must also
should not be positioned higher than 4 ft (1.2
be done before each use of the remote).
Metres) from the floor.
• Once the remote is unlocked, press the
• NEVER place the remote control on the
'MODE" button again and the unit will quickly
storage hook on the heater when it is in use.
beep 5 times telling the user the signal was
This will upset the readings and prevent
received and the remote is synchronised. In
proper and satisfactory operation. (See Fig. 5)
the event that your remote control does not
• The "Room" temperature will always display
communicate- "sync" with your main unit after
on the remote screen if good batteries are in
reading and following the operating
the remote.
instructions, please follow the below set up:
• If the batteries are running low on power, a
•
Hold down both mode button on the
low battery indicator will appear on the
remote control and main unit for 5 seconds
remote. Low batteries will effect transmission
(the power LED will blink once quickly).
distance and the screen contrast. We
•
Release the mode button and the main
recommend replacing batteries immediately.
unit will begin to beep.
Do not mix old and new batteries.
3
• Every minute while in "AUTO" mode, the
remote control communicates with the heater.
If the remote control goes out of range and/or
has low batteries, the communication will
stop, and after 8 minutes of non-
communication, the heater will shut off.
• Do not cover the remote control whilst in use
as this may affect the accuracy of the
temperature reading.
HEATER OPERATION WITH REMOTE
When the heater is plugged into the mains
supply, the power light (Red) will illuminate to
signal that the unit is in stand-by mode.
Manual Operation with remote
1. Press "MODE" button for 2 seconds to unlock
REMOTE CONTROL
TM
the remote.
2. Press "MODE" button on the remote. The
remote screen will display "ON". The "ON"
light will illuminate. In this mode, the heater
will operate continuously.
Auto Thermostat Operation with
remote
1. Press "MODE" button for 2 seconds to unlock
the remote.
2. Press "MODE" button on remote until the
remote screen displays "ON" and "AUTO".
The "Set" temperature is displayed next to the
"Room" temp. The "Auto" light on heater will
illuminate. The heater and "ON" light will cycle
on and off as the unit maintains the "Set"
temperature.
3. To turn heater "Off", unlock remote, then
press the "MODE" button and the remote
screen display will clear except for the "Room"
temperature and the heater will shut off.
NOTE: It is normal for the heater to cycle on
and off as it maintains the preset temperature.
To prevent the heater from cycling, you need to
raise the thermostat setting.
ADJUSTING SET TEMPERATURE
1. Press 'MODE' button for 2 seconds to unlock
the remote.
2. Increase - When in "AUTO" mode, press the
(+) button on the remote. The "Set" number
will increase with each press. Hold the button
down to scroll. The minimum temp is 13ºC
and the maximum is 26ºC. The remote scrolls
one digit at a time in a continuous loop. 13ºC,
14º...25º, 26º, 13º, 14º....
3. Decrease - When in 'AUTO' mode, press the
(-) button on the remote. The "Set" number
will decrease with each press. The minimum
temp is 13ºC and the maximum is 26ºC. The
remote scrolls one digit at a time in a
continuous loop. 13º, 14º...25º, 26º, 13º,
14º....
HEATER OPERATION without remote
When the heater is plugged into the mains
supply, the power light (Red) (
) will illuminate
to signal that the unit is in stand-by mode.
Remote and heater are OFF:
1. Press the "MODE" button on the heater the
first time. The "ON" light illuminates and the
heater runs continuously.
2. Press the "MODE" button a second time and
the heater shuts off.
NOTE: The "Auto On" light on the heater only
illuminates when the heater is set to "auto"
mode by the remote.
Remote is ON and Heater is ON:
1. Press the "MODE" button on the heater. The
heater will then switch "Modes"; The heater's
lights will reflect the change. The remote will
display a different mode - the mode in which it
was set to last. If a button is pressed on the
remote (after unlocking), the remote's signal
will override the "Mode" on the heater and the
two will be back in sync.
TIMER FUNCTIONS
Using Timer to turn heater off (set
with heater operating)
1. On the remote, hold 'MODE' button for 2
seconds to unlock remote.
2. Push (+) and (-) together at once:
• "Timer" and 1Hr appears on the screen.
3. Push (+) and (-) to adjust the number of hours
the heater will run before it automatically
shuts itself off.
• You can choose from:1,2,3,4,5,6,7,8 hours
• 1 through 8 will scroll in a continuous loop
4. After you have made your selection, the
whole screen flashes for 5 times 5 seconds
after last button push of (+) or (-) then goes
back to previous mode. The "Timer" remains
lit to show the timer function has been set.
5. At any time if you unlock the remote and push
the 'MODE' button to turn the heater off the
timer setting will be erased and "Timer" will
disappear from the remote.
6. To check how much time is remaining, press
and hold the (+) and (-) buttons
simultaneously.
NOTE: The remote does not have to be
unlocked to check the time remaining.
Using Timer to turn heater on (set with
heater off)
This function is used to preheat a room by
setting the timer.
4
Advertisement
