VDO CD 2203 User Manual page 6

This can only be accomplished by
persons familiar with automotive
electrical and mechanical systems.
After Connection, see "SPECIAL FUNCTIONS'
(page 13) for calibration procedure.
• Electronic antenna/Motorised antenna
Connect pin A5 to the power supply for an
electronic antenna or the control wire for the
relay of an automatic motorised antenna. Use
the small connector supplied.
Do not use this connection for the supply
lead of the aerial motor!
• Pilot light :
When the car headlights are switched on, the
backlight to the power key remains illuminated
(even when the radio is switched off).
Connect pin A6 to the dashboard illumination
wiring of the car. Use the small connector
provided.
Note : In certain car (e.g. VW Passat) the
dashboard illumination is dimmed by a digitally
modulated signal (PWM - Pulse Width
Modulation). This PWM signal can disturb the
illumination display of the car radio. In this
case, connect pin A6 to the switch signal of
the low beam headlight. Please consult your
car dealers for more information.
CONNECTOR B** (fig. 3)
Loudspeakers (use 4 ohm loudspeakers only)
• Do not connect any of the loudspeaker leads to
earth or directly to a booster/amplifier without
high level input or via an external fader! You can
connect the loudspeaker leads directly to an
amplifier with high level input.
• Connecting 4 loudspeakers:
Front
Left+ Green [B5]
Left- Green/black [B6]
Right+ Grey [B3]
Right- Grey/black [B4]
1
CONNECTOR C
Yellow Connector C1 for Pre-out* (fig. 4)
• Connect a power amplifier (with 2 or 4*
additional loudspeaker) to this set with the RCA
cable.
– Connect Red socket to Right channel and white
socket to Left channel.
– Connect Blue wire to Amplifier Remote on/off.
* Depending on version
** For this accessory, see your dealer
6
Green connector C2 (fig. 5)
Steering wheel remote control
You can connect certain car steering wheel
mounted remote control to this set via an interface.
Please consult your dealer for the correct interface.
Pink wire (Telephone mute)
:
• If your car telephone or the car kit of your mobile
– Connect the telephone mute wire to the Pink
– See 'SAM' (page 14); select
Green wire (Navigation mute)*
• If your car navigation computer provides a mute
– Connect the Navigation mute wire to the Green
– See 'SAM' (page 14); select
Blue connector C3 for our analogue CD
changer* or an Auxiliary equipment*. (available
separately)
• You can connect our analogue CD changer to
– Select option 'CHANGER' in 'SAM' (page 14).
• You can connect the audio output of auxiliary
– Select option 'AUX IN' in 'SAM' (page 14).
Rear
White [B7]
OTHERS CONNECTIONS
White/black [B8]
Telephone in (fig. 8)
Blue [B1]
• You can connect our hands-free phone kit
Blue/black [B2]
– Select option 'HFREE' and set 'HFREE LO' or
phone provides a mute signal, it can be used to
automatically interrupt the set's sound output.
lead wire.
option 'TEL' and set 'MUTE LO' or 'MUTE HI'
(according to phone type) to automatically
interrupt the set's sound output when using your
car phone.
signal, it can be used to automatically interrupt
the set's sound output during voice guidance.
lead wire.
option 'NAV' and set 'LOW' or 'HIGH' according
to the navigation computer's mute signal.
this set (fig. 6)
equipment e.g. in-car video system (instead of
a CD Changer) to this set (fig. 7) using a
separate accessory cable.
(available separately) via the connector D. See
mounting and connecting instructions for the
hands-free kit.
'HFREE HI' (according to phone type) in 'SAM'
(page 14) to automatically interrupt the set's
sound output when receiving or making a phone
call.