Advertisement
This Die-cast aluminum heat sink is designed
This Die-cast aluminum heat sink is designed
This Die-cast aluminum heat sink is designed
This Die-cast aluminum heat sink is designed
This Die-cast aluminum heat sink is designed
to dissipate massive amounts of heat from
to dissipate massive amounts of heat from
to dissipate massive amounts of heat from
to dissipate massive amounts of heat from
to dissipate massive amounts of heat from
the MOSFET drivers, while delivering crisp
the MOSFET drivers, while delivering crisp
the MOSFET drivers, while delivering crisp
the MOSFET drivers, while delivering crisp
the MOSFET drivers, while delivering crisp
clean sound with warm rich bass character-
clean sound with warm rich bass character
clean sound with warm rich bass character
clean sound with warm rich bass character-
clean sound with warm rich bass character
istics. We have to tie-down this complex cir
istics. We have to tie-down this complex cir-
istics. We have to tie-down this complex cir
istics. We have to tie-down this complex cir
istics. We have to tie-down this complex cir-
cuit board on three sides to spread the heat
cuit board on three sides to spread the heat
cuit board on three sides to spread the heat
cuit board on three sides to spread the heat
cuit board on three sides to spread the heat
evenly.
-
eal
All your connections are on one side for an
All your connections are on one side for an
All your connections are on one side for an
extremely simple installation.
CLASS A/B SERIES
•
Jet Black Texture Coat Finish
•
All MOSFET Transistor Amplifier
•
Pulse Width Modualtion Circuitry
•
Three-Way Protection Circuitry (short, thermal & overload)
•
2 Ohm Stereo, 4 Ohm Bridged Stable
•
Tri-Mode Capable
•
Selectable Hi/Full/Low Pass Crossovers
•
Pre-Amp Outputs (ex. 1200/4)
•
Dash Mount Remote Gain Control (2 ch. models)
BAMF800/2
BAMF1250/2
BAMF1800/2
BAMF2200/2
BAMF2600/2
BAMF1200/4
BAMF1600/4
CLASS D SERIES
• Jet Black Texture Coat Finish
• All MOSFET Transistor Amplifier
• Pulse Width Modualtion Circuitry
• Three-way Protection Circuitry (short, thermal & overload)
• 1 Ohm Load Stable
• Bridged Synchronization (strap amps together for double power!)
• Low Pass & Subsonic Filters
• Pre-Amp Outputs
• Dash Mount Remote Gain Control
• 200mV-6V Low Level Inputs
BAMF2000/1D
BAMF4000/1D
BAMF5500/1D
S53075.indd 3
COMMON FEATURES
COMMON FEATURES
No.
RMS @ 4Ω
RMS @ 2Ω
Chs.
(watts)
(watts)
2
2 x 150
2 x 180
2
2 x 220
2 x 280
2
2 x 300
2 x 380
2
2 x 370
2 x 450
2
2 x 450
2 x 540
4
4 x 100
4 x 125
4
4 x 150
4 x 180
COMMON FEATURES
No.
RMS @ 4Ω
RMS @ 2Ω
Chs.
(watts)
(watts)
1
600
900
1
1,200
1,700
1
1,700
2,500
•
200mV - 6V Low Level Input Sensitivity
•
Variable 12dB 30-250Hz LPF
•
Variable 12dB 50-500Hz HPF
•
Variable 0-12dB 45Hz Bass Boost
•
Variable 12 dB 15-50Hz Subsonic Filter (ex. 800/2 & 4ch. model)
•
Frequency Response: 10Hz - 30kHz
•
Signal-to-Noise Ratio: 97dB
•
Total Harmonic Distortion: .02%
•
4 ga. Power & 8 ga. Speaker Terminals
Sphere amps
Bridged @ 4Ω
MAX Power
(watts)
(watts)
1 x 360
800
1 x 560
1,250
1 x 760
1,800
1 x 900
2,200
1 x 1,080
2,600
2 x 250
1,200
2 x 360
1,600
• Variable 12dB 40-200Hz LPF
• Variable 12dB 20-50Hz Subsonic Filter
• Variable 0-18dB 45Hz Bass Boost
• Frequency Response: 15-150Hz
• Signal-to-Noise Ratio: 100dB
• Total Harmonic Distortion: .5%
• 180
0
Phase Switch
• Direct Input 4 ga. Power & 8 ga. Speaker Terminals
RMS @ 1Ω
MAX Power
(watts)
(watts)
1,200
2,000
2,200
4,000
3,200
5,500
Length: (in)
Bass Knob
(2.125"h x 8.25"w)
Included
10.125"
No
11.375"
Yes
13.75"
Yes
15"
Yes
16.875"
Yes
11.875"
No
13.75"
No
Length: (in)
Bass Knob
(2.125"h x 8.25"w)
Included
11.375"
Yes
13.75"
Yes
16.875"
Yes
3
12/31/08 11:35:30 AM
Advertisement
