Direct Function; Multi Operation And System Off; Programming A Multi-Operation Or A Shutdown Sequence - Pioneer Elite SC-25 Operating Instructions Manual

Controlling the rest of your system (In case of SC-27)

Direct function

• Default setting: ON
You can use the direct function feature to control one
component using the remote control while at the same
time, using your receiver to playback a different
component. This could let you, for example, use the
remote control to set up and listen to a CD on the
receiver, and then use the remote control to rewind a
tape in your VCR while you continue to listen to your CD
player.
When direct function is on, any component you select
(using the input function buttons) will be selected by both
the receiver and the remote control. When you turn direct
function off, you can operate the remote control without
affecting the receiver.
1 While pressing MULTI OPERATION, press HOME
MENU.
The remote LCD display shows SETUP.
Use / to select DIRECT F, then press ENTER.
2
The LCD on the remote prompts you for the button of the
input function you want to control.
3 Press the input function button for the component
you want to control, then press ENTER.
Use / to switch direct function ON or OFF, then
4
press ENTER.
The LCD shows OK to confirm the setting.

Multi Operation and System Off

The Multi Operation feature allows you to program a
series of up to 5 commands for the components in your
system. For example, you could turn on your TV, turn on
your DVD player and start playing the loaded DVD using
only two buttons on the remote control.
Similar to multi operations, System Off allows you to use
one button to stop and switch off a series of components
in your system at the same time.
Note
1 • Before Multi Operation and System Off will work correctly, you must setup the remote to work with your TV and other components (see
Operating multiple receivers on page 103 for more on this).
• Some units may take some time to power up, in which case multiple operations may not be possible.
• Power on and off commands only work with components that have a standby mode.
1
Programming a multi-operation or a
shutdown sequence
Set the remote control operation mode selector switch to
RECEIVER when you want to program this receiver's
operations, to SOURCE when you want to program
operations of other components.
MAIN MAIN
RECEIVER SOURCE
ZONE2 3
MULTI MULTI
OPERATION OPERATION
DVD DVD BD BD TV TV DVR DVR
TV
HOME MEDIA
VIDEO1 VIDEO1 VIDEO2 VIDEO2 HDMI HDMI GALLERY
USB USB CH
iPod CD CD CD-R CD-R TUNER
MULTI CH
PHONO PHONO IN XM SIRIUS
TV CONTROL
INPUT SELECT
INPUT
1 While pressing MULTI OPERATION, press HOME
MENU.
The remote LCD display shows SETUP.
Use / to select MULTI OP or SYS OFF from the
2
menu and press ENTER.
If you selected Multi Operation (MULTI OP), the LCD on
the remote prompts you for an input function button.
If you selected System Off (SYS OFF), go to step 4.
3 Press the input function button for the component
that will start the multi-operation, then press ENTER.
For example, if you want to start the sequence by
switching on your DVD player, press DVD.
Use / to select CODE EDT, then press ENTER.
4
To erase any previously stored multi-operations (or
shutdown sequences) select CODE ERS above.
Use / to select a command in the sequence, then
5
press ENTER.
If this is the first command in the sequence, select 1ST
CODE. Otherwise, simply choose the next command in
the sequence. PRES KEY flashes after you press ENTER.
6 If necessary, press the input function button for the
component whose command you want to input.
This is only necessary if the command is for a new
component (input function).
7 Select the button for the command you want to
input.
The following remote control commands can be selected:
TV CONTROL
INPUT MUTE MUTE
AUDIO VIDEO
PARAMETER PARAMETER
TUNE
TOOLS
LIST
TOP MENU T.EDIT
BAND GUIDE
SOURCE
RECEIVER RECEIVER
PRESET PRESET
ENTER ENTER
VOL
CATEGORY
RETURN
VOL
HOME HOME
MENU MENU
TUNE
iPod CTRL
STATUS PHASE CTRL CH LEVEL
MUTE MUTE
THX MPX PQLS MEMORY
10
99
en