Related Manuals for HP J4900B
Summary of Contents for HP J4900B
- Page 1 Installation and Getting Started Guide ProCurve Series 2600 Switches Power over Ethernet Devices www.procurve.com...
- Page 3 ProCurve Series 2600 Switches Installation and Getting Started Guide...
- Page 4 WARRANTIES OF MERCHANTABILITY AND FITNESS This document contains proprietary information, which is FOR A PARTICULAR PURPOSE. Hewlett-Packard shall not be protected by copyright. No part of this document may be liable for errors contained herein or for incidental or consequential...
-
Page 5: Table Of Contents
Contents 1 Introducing the Switch Front of the Switch ..........1-3 Network Ports . - Page 6 6. Connect the Network Cables ....... 2-20 Using the RJ-45 Connectors ......2-20 Connecting Cables to mini-GBICs .
- Page 7 Testing the Switch by Resetting It ......4-9 Checking the Switch LEDs ....... . 4-9 Checking Console Messages .
- Page 8 Straight-Through Twisted-Pair Cable for 1000 Mbps Network Connections ......B-9 Cable Diagram ......... B-9 Pin Assignments .
-
Page 9: Introducing The Switch
The 2600-PWR Switches also support Redundant Power Supply and Power over Ethernet (PoE) technologies. ProCurve Switch 2650 (J4899B) ProCurve Switch 2626 (J4900B) ProCurve Switch 2650-PWR (J8165A) ProCurve Switch 2626-PWR (J8164A) ProCurve Switch 2600-8-PWR with Gigabit Uplink (J8762A) Throughout this manual, these switches will be referred to as the Series 2600 Switches and the Series 2600-PWR Switches. - Page 10 Introducing the Switch ■ The Switch 2650 and 2650-PWR, has 48 auto-sensing 10/100Base-TX RJ- 45 ports with two dual-personality Gigabit Uplink ports. The Switch 2626 and 2626-PWR, has 24 auto-sensing 10/100Base-TX RJ- ■ 45 ports with two dual-personality Gigabit Uplink ports. ■...
-
Page 11: Front Of The Switch
Introducing the Switch Front of the Switch Front of the Switch Power Self Test and Fan ProCurve Switch 2650 Switch port LEDs and Fault Status LEDs LEDs Dual-personality ports Port LED View select 10/100Base-TX RJ-45 ports Reset and Clear (1000Base-T or mini-GBIC) button and indicator LEDs buttons... -
Page 12: Network Ports
Introducing the Switch Front of the Switch Network Ports ■ 8, 24, or 48 auto-sensing 10/100Base-TX ports. All these ports have the “HP Auto MDIX” feature, which means that you can use either straight-through or crossover twisted-pair cables to connect any network devices to the switch. ■... - Page 13 Introducing the Switch Front of the Switch Switch LEDs State Meaning Self Test The normal operational state; the switch is not undergoing self test. (green) The switch self test and initialization are in progress after you have power labeled “Test” cycled or reset the switch.
-
Page 14: Port Leds
Introducing the Switch Front of the Switch Port LEDs The port LEDs provide information about the individual switch ports. Table 1-2. Port LEDs Switch LEDs State Meaning Switch 2626 and Switch 2650 Port LEDs Displays port link information, network activity information, whether the port is configured for full-duplex operation, or the speed of the connection depending on the (green –... -
Page 15: Multiple-Display Port Leds - Port Led View Or Led Mode Select Button And Indicator Leds
Introducing the Switch Front of the Switch Multiple-Display Port LEDs - Port LED View or LED Mode Select Button and Indicator LEDs To optimize the amount of information that can be displayed for each of the switch ports in the limited space available, the Series 2600 Switches use multiple-display LEDs for each port. - Page 16 Introducing the Switch Front of the Switch Table 1-3. Multiple-Display Port LEDs Switch LEDs State Meaning Switch 2626 and Switch 2650 Port LED View Indicates that the Port LEDs are displaying link information: indicator LEDs • if the Port LED is on, the port is enabled and receiving a link indication from the connected device.
-
Page 17: Reset Button
Introducing the Switch Front of the Switch Reset Button This button is used to reset the switch while it is powered on. This action clears any temporary error conditions that may have occurred and executes the switch self test. Clear Button This button is used for these purposes: Deleting Passwords - When pressed by itself for at least one second, the ■... -
Page 18: Back Of The Switch
Introducing the Switch Back of the Switch Back of the Switch ProCurve Switch 2626 and 2650 non-PWR Cooling vent - make sure this is not obstructed for proper switch operation Console Console Port AC power connector ProCurve Switch 2626-PWR and 2650-PWR Cooling vent - make sure this is not obstructed for proper switch operation HP ProCurve... -
Page 19: Console Port
Introducing the Switch Switch Features Console Port This port is used to connect a console to a Series 2600 Switch by using the serial cable supplied with each switch. This connection is described under “8. (Optional) Connect a Console to the Switch” on page 30 in chapter 2, “Installing the Series 2600 Switches.”... - Page 20 Introducing the Switch Switch Features ■ automatically negotiated full-duplex operation for the 10/100 and 10/100/1000 RJ-45 ports when connected to other auto-negotiating devices—the mini-GBIC ports always operate at full duplex. easy management of the switches through several available interfaces: ■ •...
-
Page 21: Installing The Switch
Installing the Switch The ProCurve Series 2600 Switches come with an accessory kit that includes the brackets for mounting the switch in a standard 19-inch telco rack, in an equipment cabinet, or on a wall. The brackets are designed to allow mounting the switch in a variety of locations and orientations. - Page 22 Installing the Switch Included Parts ■ AC power cord, one of the following: Non-PWR Switches PWR Switches and 2600-8-PWR Australia/New Zealand 8120-6803 8120-6810 China 8120-8377 8120-8471 Continental Europe 8120-6802 8120-6811 Denmark 8120-6806 8120-6814 Japan 8120-6804 8120-6804 Switzerland 8120-6807 8120-6815 United Kingdom/Hong Kong/Singapore 8120-8709 8120-6809 United States/Canada/Mexico...
-
Page 23: Installation Procedures
Installing the Switch Installation Procedures Installation Procedures These steps summarize your switch installation. The rest of this chapter provides details on these steps. Prepare the installation site (page 2-5). Make sure the physical envi- ronment into which you will be installing the switch is properly prepared, including having the correct network cabling ready to connect to the switch and having an appropriate location for the switch. -
Page 24: Installation Precautions
Installing the Switch Installation Procedures Installation Precautions Follow these precautions when installing your ProCurve Series 2600 Switches. W A R N I N G ■ The rack or cabinet should be adequately secured to prevent it from becoming unstable and/or falling over. Devices installed in a rack or cabinet should be mounted as low as possible, with the heaviest devices at the bottom and progressively lighter devices installed above. -
Page 25: Prepare The Installation Site
Installing the Switch Installation Procedures 1. Prepare the Installation Site ■ Cabling Infrastructure - Ensure the cabling infrastructure meets the necessary network specifications. See the following table for cable types and lengths, and see appendix B, “Switch Ports and Network Cables” more information: Table 2-1. - Page 26 Installing the Switch Installation Procedures Port Type Cable Type Length Limits Fiber Optic Cables Gigabit-SX Multimode fiber-optic cables fitted with LC 220 meters to 550 meters depending on the (on Gigabit-SX-LC connectors cable used. See “Fiber-Optic Cables” on page mini-GBIC) for more information.
-
Page 27: Installing Or Removing Mini-Gbics
Installing the Switch Installation Procedures 2. Installing or Removing mini-GBICs You can install or remove a mini-GBIC from a mini-GBIC slot without having to power off the switch. Use only ProCurve mini-GBICs. N o t e s ■ The mini-GBIC slots are shared with the two 10/100/1000Base-T RJ-45 ports. - Page 28 Installing the Switch Installation Procedures Removing the mini-GBICs N o t e You should disconnect the network cable from the mini-GBIC before removing it from the switch. Depending on when you purchased your ProCurve mini-GBIC, it may have either of three different release mechanisms: a plastic tab on the bottom of the mini-GBIC, a plastic collar around the mini-GBIC, or a wire bail.
-
Page 29: Verify The Switch Passes Self Test
Installing the Switch Installation Procedures 3. Verify the Switch Passes Self Test Before mounting the switch in its network location, you should first verify it is working properly by plugging it into a power source and verifying it passes its self test. Connect the power cord supplied with the switch to the power connector on the back of the switch, and then into a properly grounded electrical outlet. -
Page 30: Led Behavior
Installing the Switch Installation Procedures Check the LEDs on the switch as described below. Switch 2650 Self Test LED Switch port LEDs Power and Fault LEDs When the switch is powered on, it performs its diagnostic self test. Self test takes approximately 50 seconds to complete. -
Page 31: Mount The Switch
Installing the Switch Installation Procedures When the self test completes successfully: • The Power and Fan Status LEDs remain on. • The Fault and Self Test LEDs go off. • The port LEDs on the front of the switch go into their normal opera- tional mode: –... -
Page 32: Rack Mounting The 2626-Pwr And 2650-Pwr Switches
Installing the Switch Installation Procedures E q u i p m e n t The 12-24 screws supplied with the switch are the correct threading for C a b i n e t standard EIA/TIA open 19-inch racks. If installing the switch in an equipment cabinet such as a server cabinet, use the clips and screws that came with the N o t e cabinet in place of the 12-24 screws that are supplied with the switch. - Page 33 Installing the Switch Installation Procedures N o t e The mounting brackets have multiple mounting holes and can be rotated allowing for a wide variety of mounting options. These include mounting the switch so that its front face is flush with the face of the rack, or mounting it in a more balanced position as shown in the illustration above.
-
Page 34: Rack Mounting The Non-Pwr Switches And The 2600-8-Pwr Switch
Installing the Switch Installation Procedures Rack Mounting the Non-PWR Switches and the 2600-8-PWR Switch Use a #1 Phillips (cross-head) screwdriver and attach the mounting brackets to the switch with the included 8-mm M4 screws. 8 mm M4 screws N o t e The mounting brackets have multiple mounting holes and can be rotated allowing for a wide variety of mounting options. - Page 35 Installing the Switch Installation Procedures Hold the switch with attached brackets up to the rack and move it vertically until rack holes line up with the bracket holes, then insert and tighten the four number 12-24 screws holding the brackets to the rack. Install 12-24 screws 2-15...
-
Page 36: Flat Wall Mounting
Installing the Switch Installation Procedures Flat Wall Mounting You can mount the Non-PWR switches on a wall as shown in the illustration on the next page. However, this is not supported for the 2626-PWR or the 2650- PWR switches. Wall mounting the PWR switches is not supported because of the size and weight of the devices. -
Page 37: Wall Mounting The Series 2600 Non-Pwr Switches
Installing the Switch Installation Procedures Wall mounting the Series 2600 Non-PWR Switches Use a #1 Phillips (cross-head) screwdriver and attach the mounting brackets to opposite corners of the switch with the included 8-mm M4 screws. Attach the switch to the wall or wood surface with two 5/8-inch (15.875 mm) number 12 wood screws (not included). -
Page 38: Wall Mounting The Series 2600-8-Pwr Switch
Installing the Switch Installation Procedures Wall mounting the Series 2600-8-PWR Switch Use a #1 Phillips (cross-head) screwdriver and attach the mounting brackets to the switch with the included 8-mm M4 screws. Attach the switch to the wall or wood surface with two 5/8-inch number 12 wood screws (not included). -
Page 39: Horizontal Surface Mounting
Installing the Switch Installation Procedures Horizontal Surface Mounting Place the switch on a table or other horizontal surface. The switch comes with rubber feet in the accessory kit that can be used to help keep the switch from sliding on the surface. Attach the rubber feet to the four corners on the bottom of the switch within the embossed angled lines. -
Page 40: Connect The Network Cables
Installing the Switch Installation Procedures 6. Connect the Network Cables Connect the network cables, described under “Cabling Infrastructure” (page 2-5), from the network devices or your patch panels to the fixed RJ-45 ports on the switch or to any mini-GBICs you have installed in the switch. Using the RJ-45 Connectors To connect: Push the RJ-45 plug into the RJ-45... -
Page 41: Connecting Cables To Mini-Gbics
Installing the Switch Installation Procedures Connecting Cables to mini-GBICs N o t e The mini-GBIC slots are shared with the two 10/100/1000Base-T RJ-45 ports. If a mini-GBIC is installed in a slot, the associated RJ-45 port is disabled. If you have any mini-GBICs installed in the switch, the type of network connections you will need to use depends on the type of mini-GBICs you have installed. -
Page 42: Rps/Eps Operation
Installing the Switch Installation Procedures RPS/EPS Operation The RPS/EPS monitors the power signal from the switch by detecting that the RPS/EPS is connected to a switch with an RPS/EPS cable. When the power from the switch is no longer detected, the RPS/EPS will turn on and provide power to the switch within 1 millisecond. -
Page 43: 600 Rps/Eps Leds
Installing the Switch Installation Procedures 600 RPS/EPS LEDs The 600 RPS/EPS LEDs are located on the back of the device. These LEDs are duplicated on the front of the device for your convenience. The following graphic shows an example of the back of the 600 EPS/RPS. There are two green LEDs for each RPS and EPS port: Device Connected ■... - Page 44 Installing the Switch Installation Procedures 600 RPS/EPS Connectivity The following illustration shows an example of connectivity between an RPS/ EPS device and a switch device as a redundant AC power supply. RPS Power: 12V backup to one connected device. Lowest-numbered port has priority. EPS Power: 50V 370W total for PoE applications.
- Page 45 Installing the Switch Installation Procedures The following illustration shows an example of connectivity between an RPS/ EPS device and six switch devices as a redundant AC power supply. 2650-PWR switches Highest priority connected to port 1 600 RPS/EPS The 600 RPS/EPS can provide backup power for up to six switches. The 600 RPS/EPS can supply power to only one connected and failed switch at a time.
- Page 46 Installing the Switch Installation Procedures The following illustration demonstrates an example of connectivity between an RPS/EPS device and a Switch device as a PoE power supply. RPS Power: 12V backup to one connected device. Lowest-numbered port has priority. EPS Power: 50V 370W total for PoE applications.
-
Page 47: 610 Eps Leds
Installing the Switch Installation Procedures 610 EPS LEDs 610 EPS Power and Backup Power EPS Port LEDs Fault LEDs Port LEDs hp procurve EPS Ports Pair A (408 W total for PoE applications) EPS Ports Pair B (408 W total for PoE applications) Device Device Connected... - Page 48 Installing the Switch Installation Procedures 12 V 7.5 A Line: 50/60 Hz. 100-240 V~ 7.5 A 50 V 16 A 12 V 7.5 A Line: 50/60 Hz. 100-240 V~ 7.5 A 50 V 16 A hp procurve EPS Ports Pair A (408 W total for PoE applications) EPS Ports Pair B...
- Page 49 Installing the Switch Installation Procedures 12 V 7.5 A Line: 50/60 Hz. 100-240 V~ 7.5 A 50 V 16 A 12 V 7.5 A Line: 50/60 Hz. 100-240 V~ 7.5 A 50 V 16 A 12 V 7.5 A Line: 50/60 Hz. 100-240 V~ 7.5 A 50 V 16 A...
-
Page 50: Optional) Connect A Console To The Switch
Installing the Switch Installation Procedures 8. (Optional) Connect a Console to the Switch The Series 2600 Switches have a full-featured, easy to use console interface for performing switch management tasks including the following: monitor switch and port status and observe network activity statistics ■... -
Page 51: Direct Console Access
Installing the Switch Installation Procedures Direct Console Access To connect a console to the switch, follow these steps: Console Connect the PC or Console port terminal to the switch’s Console Port using the console cable included with the switch. (If your PC or terminal has a 25-pin Console cable supplied serial connector, first... -
Page 52: Sample Network Topologies For Non-Pwr Switches
Installing the Switch Sample Network Topologies for Non-PWR Switches Sample Network Topologies for Non-PWR Switches This section shows a few sample network topologies in which the Switch 2650 is implemented. For more topology information, see the ProCurve networking products Web site, http://www.procurve.com. As a Desktop Switch Server Twisted-pair... -
Page 53: As A Segment Switch
Installing the Switch Sample Network Topologies for Non-PWR Switches As a Segment Switch Category 5e twisted-pair straight-through or crossover cable for 1000 Mbps connection to server Server with Gigabit Gigabit fiber-optic cable Ethernet NIC to backbone Switch 2650 Twisted-pair straight-through or crossover cables to hubs Switch 2650 Switch 2650... - Page 54 Installing the Switch Sample Network Topologies for Non-PWR Switches Because the Series 2600 Switches have the “HP Auto-MDIX” and “IEEE Auto MDI/MDI-X” features, the connections between the switch and the hubs, and between the switch and end nodes or servers can be through category 5 straight-through or crossover twisted-pair cable.
-
Page 55: Connecting To A Backbone Switch
Installing the Switch Sample Network Topologies for Non-PWR Switches Connecting to a Backbone Switch To Gigabit-Ethernet backbone Switch 5308xl Switch 2650 Gigabit fiber-optic cables Switch 2650 Switch 2650 Switch 2650 The simpler desktop and segment networks shown in the previous two examples can easily be combined and expanded. -
Page 56: Sample Network Topologies For Pwr Switches
Installing the Switch Sample Network Topologies for PWR Switches Sample Network Topologies for PWR Switches This section shows a few sample network topologies implementing the Series 2600-PWR Switches. For more topology information, see the ProCurve networking products Web site, http://www.procurve.com. As a Desktop Switch Implementing PoE 600 RPS/EPS Twisted-pair... -
Page 57: As A Segment Switch Implementing Poe
Installing the Switch Sample Network Topologies for PWR Switches As a Segment Switch Implementing PoE Category 5e twisted-pair straight-through or crossover cable for 1000 Mbps connection to server Server with Gigabit Ethernet NIC 600 RPS/EPS Switch 2650 Non-PWR Twisted-pair straight- through or crossover cables Gigabit fiber-optic cable... - Page 58 Installing the Switch Sample Network Topologies for PWR Switches Connecting to a Backbone Switch Implementing PoE To Gigabit-Ethernet backbone Switch 5308xl Switch 2650 Gigabit fiber-optic cable Switch 2650 non-PWR 600 RPS/EPS Switch 2650-PWR Switch 2650-PWR Wireless Access Point 2-38...
-
Page 59: Stacking The Switch
Installing the Switch Sample Network Topologies for PWR Switches Stacking the Switch Switch 2600 and 2600-PWR Series devices can be connected together, through standard network connections, and managed through a single IP address. Up to 16 switches can be connected together in such a “virtual stack”. You identify a Switch 2600 or 2600-PWR Series device as the “Commander”... - Page 60 — This page is intentionally unused. —...
-
Page 61: Configuring The Switch
Configuring the Switch This chapter is a guide for using the console Switch Setup screen to quickly assign an IP (Internet Protocol) address and subnet mask to the switch, set a Manager password, and, optionally, configure other basic features. For more information on using the switch console and the web browser interface, please see the Management and Configuration Guide, which is on the Documentation CD-ROM that came with your switch. -
Page 62: Using The Console Setup Screen
Configuring the Switch N o t e By default, the switch is configured to acquire an IP address configuration from a DHCP or Bootp server. To use DHCP/Bootp instead of the manual method described in this chapter, see “DHCP/Bootp Operation” in the Management and Configuration Guide, which is on the Documentation CD-ROM that came with your switch. - Page 63 Configuring the Switch to the IP Config (DHCP/Bootp) field and use the Space bar to select the [Tab] Manual option. to the IP Address field and enter the IP address that is compatible with [Tab] your network. to the Subnet Mask field and enter the subnet mask used for your [Tab] network.
-
Page 64: Where To Go From Here
Configuring the Switch Where to Go From Here The above procedure configures your switch with a Manager password, IP address, and subnet mask. As a result, with the proper network connections, you can now manage the switch from a PC equipped with Telnet, and/or a web browser interface. -
Page 65: Using The Ip Address For Remote Switch Management
Configuring the Switch Using the IP Address for Remote Switch Management Using the IP Address for Remote Switch Management With your switch, you can use the switch’s IP address to manage the switch from any PC that is on the same subnet as the switch. You can use either a Telnet session or a standard web browser to manage the switch. - Page 66 Configuring the Switch Using the IP Address for Remote Switch Management For more information on using the web browser interface, please see the Management and Configuration Guide, which is on the Documentation CD-ROM that came with your switch. An extensive help system is also available for the web browser interface. To access the help system though, the subnet on which the switch is installed must have access to the internet.
-
Page 67: Troubleshooting
Troubleshooting This chapter describes how to troubleshoot your ProCurve Series 2600 Switch. This document describes troubleshooting mostly from a hardware perspective. You can perform more in-depth troubleshooting on these devices using the software tools available with the switches, including the full- featured console interface, the built-in web browser interface, and ProCurve Manager, the SNMP-based network management tool. - Page 68 Troubleshooting Basic Troubleshooting Tips C a u t i o n Because the Series 2600 Switches behave in this way (in compliance with the IEEE 802.3 standard), if a device connected to the switch has a fixed configuration at full duplex, the device will not connect correctly to the switch.
- Page 69 Troubleshooting Basic Troubleshooting Tips ■ Check the port configuration. A port on your switch may not be operating as you expect because it has been put into a “blocking” state by Spanning Tree, GVRP (automatic VLANs), or LACP (automatic trunking). (Note that the normal operation of the Spanning Tree, GVRP, and LACP features may put the port in a blocking state.) Or, the port just may have been configured as disabled through software.
-
Page 70: Diagnosing With The Leds
Troubleshooting Diagnosing with the LEDs Diagnosing with the LEDs Table 4-1 shows LED patterns on the switch and the switch modules that indicate problem conditions. Check in the table for the LED pattern you see on your switch. Refer to the corresponding diagnostic tip on the next few pages. Table 4-1. - Page 71 Troubleshooting Diagnosing with the LEDs Diagnostic Tips: Problem Solution ➊ The switch is not 1. Verify the power cord is plugged into an active power source and to the switch. Make plugged into an sure these connections are snug. active AC power 2.
- Page 72 Troubleshooting Diagnosing with the LEDs Problem Solution ➏ The network Try the following procedures: connection is not • For the indicated port, verify that both ends of the cabling, at the switch and the working connected device, are connected properly. properly.
- Page 73 Troubleshooting Diagnosing with the LEDs Problem Solution ➐ The port may be Use the switch console to see if the port is part of a dynamic trunk (through the LACP improperly feature) or to see if Spanning Tree is enabled on the switch, and to see if the port may configured, or have been put into a “blocking”...
-
Page 74: Proactive Networking
Troubleshooting Proactive Networking Proactive Networking The ProCurve Series 2600 Switches have built-in management capabilities that proactively help you manage your network including: ■ finding and helping you fix the most common network error conditions (for example, faulty network cabling, and non-standard network topologies) informing you of the problem with clear, easy-to-understand messages ■... -
Page 75: Hardware Diagnostic Tests
Troubleshooting Hardware Diagnostic Tests Hardware Diagnostic Tests Testing the Switch by Resetting It If you believe the switch is not operating correctly, you can reset the switch to test its circuitry and operating code. To reset a switch, either: ■ unplug and plug in the power cord (power cycling) press the Reset button on the front of the switch ■... -
Page 76: Testing Twisted-Pair Cabling
Troubleshooting Hardware Diagnostic Tests Testing Twisted-Pair Cabling Network cables that fail to provide a link or provide an unreliable link between the switch and the connected network device may not be compatible with the IEEE 802.3 Type 10Base-T, 100Base-TX, or 1000Base-T standards. The twisted- pair cables attached to the switch must be compatible with the appropriate standards. -
Page 77: Restoring The Factory Default Configuration
Troubleshooting Restoring the Factory Default Configuration Restoring the Factory Default Configuration As part of your troubleshooting process on the Switch, it may become necessary to return the switch configuration to the factory default settings. This clears any passwords, clears the console event log, resets the network counters to zero, performs a complete self test, and reboots the switch into its factory default configuration including deleting the IP address, if one is configured. -
Page 78: Downloading New Switch Software
HP Customer Support Services If you are still having trouble with your switch, Hewlett-Packard offers support 24 hours a day, seven days a week through the use of a number of automated electronic services. See the Customer Support/Warranty booklet that came with your switch for information on how to use these services to get technical support. -
Page 79: A Switch Specifications
Switch Specifications Physical 2600 Non-PWR Series Width Depth Height Weight 2626 (J4900B) 44.3 cm (17.4 in) 36.7 cm (14.4 in) 4.4 cm (1.73 in) 4.62 kg (10.20 lbs) 2650 (J4899B) 44.3 cm (17.4 in) 43.0 cm (16.9 in) 4.4 cm (1.73 in) 4.88 kg (10.75 lbs) -
Page 80: Environmental
Includes switch and maximum number of PoE powered devices connected to the switch at 15.4 watts. Acoustic Non-PWR 2600 Series (J4899B/J4900B) Geraeuschemission LwA=50 dB am fiktiven Arbeitsplatz nach DIN 45635 T.19 Noise Emission LwA=50 dB at virtual work space according to DIN 45635 T.19 2600-PWR switches (J8164A/J8165A) Geraeuschemission LwA=53 dB am fiktiven Arbeitsplatz nach DIN 45635 T.19... -
Page 81: Connectors
Switch Specifications Connectors ■ The 10/100/1000 Mbps RJ-45 twisted-pair ports are compatible with the following standards: • IEEE 802.3ab 1000Base-T • IEEE 802.3u 100Base-TX • IEEE 802.3 10Base-T ■ The 1000 Mbps LC fiber-optic ports on the Gigabit-SX and Gigabit-LX mini- GBIC transceivers are compatible with the IEEE 802.3z Gigabit-SX and Gigabit-LX standards. - Page 82 — This page is intentionally unused. —...
-
Page 83: B Switch Ports And Network Cables
Switch Ports and Network Cables This appendix includes switch connector information and network cable information for cables that should be used with the Switch 2600 and 2600-PWR Series devices, including minimum pin-out information and specifications for twisted-pair cables. N o t e Incorrectly wired cabling is the most common cause of problems for LAN communications. -
Page 84: Fiber-Optic Cables
Switch Ports and Network Cables Because of the increased speed provided by 1000Base-T (Gigabit-T), network cable quality is more important than for either 10Base-T or 100Base-TX. Cabling plants being used to carry 1000Base-T networking must comply with the IEEE 802.3ab standards. In particular, the cabling must pass tests for Attenuation, Near-End Crosstalk (NEXT), and Far-End Crosstalk (FEXT). -
Page 85: Mode Conditioning Patch Cord For Gigabit-Lx
Switch Ports and Network Cables Mode Conditioning Patch Cord for Gigabit-LX Mode Conditioning Patch Cord for Gigabit-LX The following information applies to installations in which multimode fiber- optic cables are connected to a Gigabit-LX port. Unlike Gigabit-SX, which connects to only multimode fiber-optic cabling, Gigabit-LX can use either single-mode or multimode cable. -
Page 86: Installing The Patch Cord
Switch Ports and Network Cables Mode Conditioning Patch Cord for Gigabit-LX Installing the Patch Cord As shown in the illustration below, connect the patch cord to the Gigabit-LX mini-GBIC with the section of single-mode fiber plugged in to the Tx (transmit) port. -
Page 87: Twisted-Pair Cable/Connector Pin-Outs
Switch Ports and Network Cables Twisted-Pair Cable/Connector Pin-Outs Twisted-Pair Cable/Connector Pin-Outs The HP Auto-MDIX Feature: In the default configuration, “Auto”, the fixed 10/100Base-TX ports on the Series 2600 Switches all automatically detect the type of port on the connected device and operate as either an MDI or MDI-X port, whichever is appropriate. - Page 88 Switch Ports and Network Cables Twisted-Pair Cable/Connector Pin-Outs ■ For 100 Mbps connections to the ports, use 100-ohm Category 5 UTP or STP cable only, as supported by the IEEE 802.3u Type 100Base-TX standard. For 1000 Mbps connections, 100-ohm Category 5e or better cabling is ■...
-
Page 89: Straight-Through Twisted-Pair Cable For 10 Mbps Or 100 Mbps Network Connections
Switch Ports and Network Cables Twisted-Pair Cable/Connector Pin-Outs Straight-through Twisted-Pair Cable for 10 Mbps or 100 Mbps Network Connections Because of the HP Auto-MDIX operation of the 10/100 ports on the switch, for all network connections, to PCs, servers or other end nodes, or to hubs or other switches, you can use straight-through cables. -
Page 90: Crossover Twisted-Pair Cable For 10 Mbps Or 100 Mbps Network Connection
Switch Ports and Network Cables Twisted-Pair Cable/Connector Pin-Outs Crossover Twisted-Pair Cable for 10 Mbps or 100 Mbps Network Connection The HP Auto-MDIX operation of the 10/100 ports on the switch also allows you to use crossover cables for all network connections, to PCs, servers or other end nodes, or to hubs or other switches. -
Page 91: Straight-Through Twisted-Pair Cable For 1000 Mbps Network Connections
Switch Ports and Network Cables Twisted-Pair Cable/Connector Pin-Outs Straight-Through Twisted-Pair Cable for 1000 Mbps Network Connections 1000Base-T connections require that all four pairs of wires be connected. Cable Diagram N o t e Pins 1 and 2 on connector “A” must be wired as a twisted pair to pins 1 and 2 on connector “B”. - Page 92 — This page is intentionally unused. —...
-
Page 93: C Safety And Emc Regulatory Statements
Safety and EMC Regulatory Statements Safety Information Documentation reference symbol. If the product is marked with this symbol, refer to the product documentation to get more information about the product. WARNING A WARNING in the manual denotes a hazard that can cause injury or death. -
Page 94: Informations Concernant La Sécurité
Safety and EMC Regulatory Statements Informations concernant la sécurité Informations concernant la sécurité Symbole de référence à la documentation. Si le produit est marqué de ce symbole, reportez-vous à la documentation du produit afin d'obtenir des informations plus détaillées. WARNING Dans la documentation, un WARNING indique un danger susceptible d'entraîner des dommages corporels ou la mort. -
Page 95: Hinweise Zur Sicherheit
Safety and EMC Regulatory Statements Hinweise zur Sicherheit Hinweise zur Sicherheit Symbol für Dokumentationsverweis. Wenn das Produkt mit diesem Symbol markiert ist, schlagen Sie bitte in der Produktdokumentation nach, um mehr Informationen über das Produkt zu erhalten. WARNING Eine WARNING in der Dokumentation symbolisiert eine Gefahr, die Verletzungen oder sogar Todesfälle verursachen kann. -
Page 96: Considerazioni Sulla Sicurezza
Safety and EMC Regulatory Statements Considerazioni sulla sicurezza Considerazioni sulla sicurezza Simbolo di riferimento alla documentazione. Se il prodotto è contras- segnato da questo simbolo, fare riferimento alla documentazione sul prodotto per ulteriori informazioni su di esso. WARNING La dicitura WARNINGdenota un pericolo che può causare lesioni o morte. -
Page 97: Consideraciones Sobre Seguridad
Safety and EMC Regulatory Statements Consideraciones sobre seguridad Consideraciones sobre seguridad Símbolo de referencia a la documentación. Si el producto va marcado con este símbolo, consultar la documentación del producto a fin de obtener mayor información sobre el producto. WARNING Una WARNING en la documentación señala un riesgo que podría resultar en lesiones o la muerte. -
Page 98: Safety Information (Japan
Safety and EMC Regulatory Statements Safety Information (Japan) Safety Information (Japan) J a p a n P o w e r C o r d W a r n i n g... -
Page 99: Safety Information (China
Safety and EMC Regulatory Statements Safety Information (China) Safety Information (China) -
Page 100: Emc Regulatory Statements
Safety and EMC Regulatory Statements EMC Regulatory Statements EMC Regulatory Statements U.S.A. FCC Class A This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against interference when the equipment is operated in a commercial environment. -
Page 101: Korea
Safety and EMC Regulatory Statements EMC Regulatory Statements Korea Taiwan... -
Page 102: European Community
Directive 73/23/EEC and the EMC Directive 89/336/EEC and carries the CE marking accordingly. Tested with Hewlett-Packard Co. products only. Mike Avery, Roseville, April 18, 2004 Regulatory Engineering Manager European Contact: Your local Hewlett-Packard Sales and Service Office or Hewlett-Packard GmbH, Department TRE, Herrenberger Strasse 140, D-71034 Böblingen (FAX:+49-7031-14-3143). C-10... -
Page 103: Declaration Of Conformity
1) J8169A for use with ProCurve Switch 2626-PWR, 2650-PWR, and RSVLC-0302 Tested with Hewlett-Packard Co. products only. Roseville, July 28, 2005 Mike Avery, Regulatory Engineering Manager European Contact: Your local Hewlett-Packard Sales and Service Office or Hewlett-Packard GmbH, Department TRE, Herrenberger Strasse 140, D-71034 Böblingen (FAX:+49-7031-14-3143). C-11... -
Page 104: Waste Electrical And Electronic Equipment (Weee) Statements
Safety and EMC Regulatory Statements Waste Electrical and Electronic Equipment (WEEE) Statements Waste Electrical and Electronic Equipment (WEEE) Statements Disposal of Waste Equipment by Users in Private Household in the European Union This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. - Page 105 Safety and EMC Regulatory Statements Waste Electrical and Electronic Equipment (WEEE) Statements Laitteiden hävittäminen kotitalouksissa Euroopan unionin alueella Jos tuotteessa tai sen pakkauksessa on tämä merkki, tuotetta ei saa hävittää kotitalousjätteiden mukana. Tällöin hävitettävä laite on toimitettava sähkölaitteiden ja elektronisten laitteiden kierrätyspisteeseen. Hävitettävien laitteiden erillinen käsittely ja kierrätys auttavat säästämään luonnonvaroja ja varmistamaan, että...
- Page 106 Safety and EMC Regulatory Statements Waste Electrical and Electronic Equipment (WEEE) Statements Smaltimento delle apparecchiature da parte di privati nel territorio dell'Unione Europea Questo simbolo presente sul prodotto o sulla sua confezione indica che il prodotto non può essere smaltito insieme ai rifiuti domestici. È responsabilità dell'utente smaltire le apparecchiature consegnan- dole presso un punto di raccolta designato al riciclo e allo smaltimento di apparecchiature elettriche ed elettroniche.
- Page 107 Safety and EMC Regulatory Statements Waste Electrical and Electronic Equipment (WEEE) Statements Descarte de Lixo Elétrico na Comunidade Européia Este símbolo encontrado no produto ou na embalagem indica que o produto não deve ser descartado no lixo doméstico comum. É responsabilidade do cliente descartar o material usado (lixo elétrico), encaminhando-o para um ponto de coleta para reciclagem.
- Page 108 — This page is intentionally unused. —...
- Page 109 Index Numerics basic switch configuration IP address … 3-3 10/100Base-TX ports manager password … 3-2 location on switch … 1-3 subnet mask … 3-3 1000Base-LH Switch Setup screen … 3-2 connections, length limitations … 2-6 basic troubleshooting tips … 4-1 ports, cables used with …...
- Page 110 cables, twisted pair console port category 3, 4, 5 … B-5 definition … 1-11 cross-over cable pin-out … B-8 location on switch … 1-3 MDI-X to MDI connections … B-7, B-9 cross-over cable MDI-X to MDI-X connections … B-8 pin-out … B-8 pin-outs …...
- Page 111 Fault LED … 1-4 installation behavior during self test … 2-11 connecting the switch to a power source … 2-19 behaviors … 1-4 horizontal surface mounting … 2-19 blinking definition … 1-5–1-6, 1-8 location considerations … 2-6 location on switch … 1-3 network cable requirements …...
- Page 112 mini-GBICs pin-outs full-duplex operation … 2-7 twisted-pair cables … B-5 slot, location on switch … 1-3 port configuration mounting the switch checking when troubleshooting … 4-3 in a rack or cabinet … 2-11 port LEDs precautions … 2-4 description … 1-6 on a horizontal surface …...
- Page 113 resetting the switch switch factory default reset … 4-11 connecting to a power source … 2-19 location of Reset button … 1-9 description … 1-1 troubleshooting procedure … 4-9 downloading new software … 4-12 RPS/EPS … 2-21 electrical specifications … A-1 cables …...
- Page 114 troubleshooting … 4-1 basic tips … 4-1 checking port configuration … 4-3 checking the console messages … 4-9 checking the LEDs … 4-9 common network problems … 4-1 connecting to fixed full-duplex devices … 4-1 diagnostic tests … 4-9 effects of improper topology … 4-2 effects of non-standard cables …...
- Page 116 Technical information in this document is subject to change without notice. © Copyright 2001, 2005, 2008 Hewlett-Packard Development Company, L.P. Reproduction, adaptation, or translation without prior written permission is prohibited except as allowed under the copyright laws. Printed in Taiwan...