Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Crestron BB-1550CW
Summary of Contents for Crestron BB-1550CW
- Page 2 This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON...
-
Page 3: Table Of Contents
Crestron BB-1550CW Wall Mount Back Box for SmarTouch Contents Wall Mount Back Box for STX-1550CW: BB-1550CW Description Installation Installation During Construction Installation After Construction Further Inquiries Future Updates Appendix: Cutout Detail of Supplied Template Return and Warranty Policies Merchandise Returns / Repair Service CRESTRON Limited Warranty Installation Guide - DOC. -
Page 5: Wall Mount Back Box For Stx-1550Cw: Bb-1550Cw
Wall Mount Back Box for STX-1550CW: BB-1550CW Description The BB-1550CW back box is wall-mounted hardware that is used to secure the DA-1550CW docking assembly (sold separately). When used with the BB-1550CW, the docking assembly provides operating power, hard-wire communications with... -
Page 6: Installation
6.63 in (16.85 cm) Installation There are two different methods of installing the BB-1550CW; installation during construction or post-construction installation. Installation during construction describes installation into a room during construction when the room is framed and the gypsum board has not been hung. The post-construction method is used after the rooms are complete and gypsum board has already been hung. - Page 7 Orient the back box enclosure as shown below (notch for manual unlatching upwards) and remove an appropriate knockout for the Cresnet wiring. Back Box Enclosure Orientation NOTCH FOR MANUAL UNLATCH TAB ACCESS REMOVED KNOCKOUT Installation Guide - DOC. 5848 Wall Mount Back Box for STX-1550CW: BB-1550CW...
- Page 8 Tighten screws only finger-tight so that final adjustments may be made during step 7 of this procedure. Loosely Secure Enclosure to Mounting Bracket Feed the Cresnet wiring through the enclosure knockout. Wall Mount Back Box for STX-1550CW: BB-1550CW Installation Guide - DOC. 5848...
-
Page 9: Installation After Construction
Locate an area on the wall that the back box (and touchpanel) will be installed. Make sure that the area is clear of studs, wires, or other obstructions within the installation area. Installation Guide - DOC. 5848 Wall Mount Back Box for STX-1550CW: BB-1550CW... - Page 10 Through the mounting bracket slots closest to the center of the bracket and using a #2 Phillips screwdriver, secure the bracket to the stud using four wood screws (not supplied). Secure Mounting Bracket to Stud Wall Mount Back Box for STX-1550CW: BB-1550CW Installation Guide - DOC. 5848...
- Page 11 14 of this procedure. Loosely Install Support Bracket 11. Position the back box enclosure near the cut-out area and feed the Cresnet wiring through the enclosure knockout. Installation Guide - DOC. 5848 Wall Mount Back Box for STX-1550CW: BB-1550CW...
- Page 12 Using a #2 Phillips screwdriver, tighten the four pair of bracket screws finger-tight plus an additional 1/8-turn. Adjust Back Box Clearance and Tighten Bracket Screws BACK BOX CLEARANCE (ALL SIDES) Wall Mount Back Box for STX-1550CW: BB-1550CW Installation Guide - DOC. 5848...
-
Page 13: Further Inquiries
Crestron BB-1550CW Wall Mount Back Box for STX-1550CW Further Inquiries If after reviewing this Installation Guide for the BB-1550CW, you cannot locate specific information or have questions, please take advantage of Crestron's award winning customer service team by calling: In the US and Canada, call Crestron’s corporate headquarters at 1-888-CRESTRON [1-888-273-7876] or 1-201-767-3400. -
Page 14: Appendix: Cutout Detail Of Supplied Template
Wall Mount Back Box for STX-1550CW Crestron BB-1550CW Appendix: Cutout Detail of Supplied Template Crestron recommends that the supplied template be used to avoid any error. However, if the template becomes lost or unusable, the dimensions of the cutout area are shown below. -
Page 15: Return And Warranty Policies
(3) years from the date of shipment to purchaser. Disk drives and any other moving or rotating mechanical parts are covered for a period of one (1) year. CRESTRON warrants all its other products for a period of one year from the defects mentioned above, excluding touchscreen display components which are covered for 90 days. - Page 16 Crestron Electronics, Inc. Installation Guide – DOC. 5848 15 Volvo Drive Rockleigh, NJ 07647 12.00 Tel: 888.CRESTRON Fax: 201.767.7576 Specifications subject to www.crestron.com change without notice.