Pioneer DJM-900NXS Operating Instructions Manual page 19

FILTER
1
The filter's cutoff frequency changes according to the beat fraction set with the
[BEAT c, d] buttons.
BEAT c, d buttons (param- Use these to set the cycle for moving the cut-off frequency as a
eter 1) time of 1/4 – 64/1 with respect to the time of one beat of the BPM.
Use this to set the cycle at which the cut-off frequency is moved.
TIME control (parameter 2)
10 to 32000 (ms)
LEVEL/ DEPTH control The further the control is turned clockwise, the more the effect
(parameter 3) is stressed.
The cycle at which the cut-off frequency is moved fluctuates
X-PAD (parameter 4)
finely.
FLANGER
1
A 1-cycle flanger effect is produced according to the beat fraction set with the [BEAT
c, d] buttons.
Short delay
Cycle
BEAT c, d buttons (param- Use these to set the 1/4 – 64/1 effect time with respect to the
eter 1) time of one beat of the BPM.
Use this to set the cycle by which the flanger effect moves.
TIME control (parameter 2)
10 to 32000 (ms)
The further the control is turned clockwise, the more the effect
LEVEL/ DEPTH control is stressed.
(parameter 3) When turned all the way counterclockwise, only the original
sound is output.
X-PAD (parameter 4) The cycle at which the flanger effect is moved fluctuates finely.
PHASER
1
The phaser effect changes according to the beat fraction set with the [BEAT c, d]
buttons.
Phase shift
Cycle
BEAT c, d buttons (param- Use these to set the cycle for moving the phaser effect as of time
eter 1) of 1/4 – 64/1 with respect to the time of one beat of the BPM.
This sets the cycle by which the phaser effect is moved.
TIME control (parameter 2)
10 to 32000 (ms)
The further the control is turned clockwise, the more the effect
LEVEL/ DEPTH control is stressed.
(parameter 3) When turned all the way counterclockwise, only the original
sound is output.
X-PAD (parameter 4) The cycle at which the phaser effect is moved fluctuates finely.
ROBOT
1
The original sound is changed to a sound like one produced by a robot.
BEAT c, d buttons (param- Use these to set the degree of the effect sound, from -100 –
eter 1) 100 %.
Use this to set the degree of the effect sound.
TIME control (parameter 2)
-100–100 (%)
LEVEL/ DEPTH control Sets the balance between the original sound and the effect
(parameter 3) sound.
X-PAD (parameter 4) This changes the degree of the effect sound.
MELODIC
1 2
The mid-range of the sound being input at the point when the [ON/OFF] button is
pressed is recorded, and the recorded sound is output according to the level of the
sound being input.
Frequency
Time
Time
BEAT c, d buttons (param-
This sets the way in which the recorded sound is played.
eter 1)
TIME control (parameter 2) This sets the way in which the recorded sound is played.
LEVEL/ DEPTH control This sets the balance between the original sound and the
(parameter 3) recorded sound.
X-PAD (parameter 4) This sets the way in which the recorded sound is played.
SLIP ROLL
1 2
The sound being input at the point when the [ON/OFF] is pressed is recorded, and
the recorded sound is output repeatedly according to the beat fraction set with the
[BEAT c, d] buttons.
When the effect time changes, the input sound is recorded again.
Original
Changed from 1/2
Effect turned on
to 1/1
Roll
1/2 repeat
BEAT c, d buttons (param- Use these to set an effect time of 1/16 – 16/1 with respect to the
eter 1) time of one beat of the BPM.
Use this to set the effect time.
TIME control (parameter 2)
10 to 4000 (ms)
LEVEL/ DEPTH control
Use this to set the balance between the original sound and ROLL.
(parameter 3)
X-PAD (parameter 4) Use this to set the effect time.
ROLL
1 2
The sound being input at the point when the [ON/OFF] is pressed is recorded, and
the recorded sound is output repeatedly according to the beat fraction set with the
[BEAT c, d] buttons.
Original
Effect turned on
1/1 roll
Repeated
BEAT c, d buttons (param- Use these to set an effect time of 1/16 – 16/1 with respect to the
eter 1) time of one beat of the BPM.
Use this to set the effect time.
TIME control (parameter 2)
10 to 4000 (ms)
LEVEL/ DEPTH control
Use this to set the balance between the original sound and ROLL.
(parameter 3)
X-PAD (parameter 4) Use this to set the effect time.
REV ROLL
1 2
The sound being input at the point when the [ON/OFF] button is pressed is
recorded, and the recorded sound is reversed then output repeatedly according to
the beat fraction set with the [BEAT c, d] buttons.
Original
Effect turned on
1/1 reverse
roll
Reversed and repeated
BEAT c, d buttons (param- Use these to set an effect time of 1/16 – 16/1 with respect to the
eter 1) time of one beat of the BPM.
Use this to set the effect time.
TIME control (parameter 2)
10 to 4000 (ms)
LEVEL/ DEPTH control
Use this to set the balance between the original sound and ROLL.
(parameter 3)
X-PAD (parameter 4) Use this to set the effect time.
1/1 repeat
19
En