Replacing The Batteries; Other Functions - THOMSON ROC2309 Operating Instructions Manual

Hide thumbs

Table Of Contents

Table of Contents

Available languages

Enlarged version

recorder, SAT: satellite receiver, cable, DVBT, ADSL

and AMP: audio equipment.

4. While the indicator is lit, enter the ﬁ rst digit of the

4-digit code proposed for the set to be controlled

(example: 0036 for Thomson).

5. Direct the remote control towards the set and try to

switch it off by pressing the key G.

6. Should the set not switch off, repeat step 2. Then

type in the next 4-digit code. Try to switch off the set

by pressing key G once. Repeat this procedure by

trying out each of the 4-digit codes.

Check of the programming:

In principle, your set is ready for receiving the remote

control commands.

Check your remote control for proper functioning by

performing the test described on page 2.

Method C – Programming by means

of code retrieval

Should none of the codes work, you still have the

possibility of retrieving the appropriate code without

having to perform any input.

1. Switch on the set you want to control.

2. Hold down the SETUP key until the red indicator

light blinks and then remains lit (the indicator light

remains on for a few seconds to give you the time

to proceed with the following steps. The indicator

lamp ﬂ ashes to signal that this time is almost up,

and then goes off). Release the SETUP key.

3. Press the key that corresponds to the type of

equipment you want to control:

TV: television set, DVD: DVD player, Video

recorder, SAT: satellite receiver, cable, DVBT,

ADSL

4. Direct the remote control towards the set and try to

switch it off by pressing the key G.

5. If the set you want to control switches off, press

OK to memorise the code.

6. Should the set not switch off, press key G as many

times as required (up to 200 times), until the set

switches off. Between pressing the keys, be sure

to leave enough time for the indicator light to go

out and then relight (about 1 second). Proceeding

this way will enable you to see whether the set

responds or not.

7. Immediately upon the switching-off of the set to be

controlled, press OK to store the code.

Check of the programming:

In principle, your set is ready for receiving the remote

control commands.

Check your remote control for proper functioning by

performing the test described on page 2.

Try out other remote control keys to ﬁ nd out the range

of functions you can control. If you think that not all

of the keys are active, repeat the procedure of this

programming method to ﬁ nd out the code supporting a

wider range of features.

Method D – Automatic

code search

With this method, the remote control scrolls through

the full code list by sending an IR signal to the set to be

controlled remotely. Proceed as follows:

1. Switch on the set you want to control.

2. Hold down the SETUP key until the red indicator

light blinks and then remains lit (the indicator light

remains on for a few seconds to give you the time

to proceed with the following steps. The indicator

lamp ﬂ ashes to signal that this time is almost up,

and then goes off).

3. Release the SETUP key.

4. Press the key that corresponds to the type of

equipment you want to control:

TV: television set, DVD: DVD player, Video

recorder, SAT: satellite receiver, cable, DVBT,

ADSL

5. Press the P+ or standby G or B (DVD/VCR only)

key. After a few seconds, the remote control begins

to scroll through the whole code list included in the

library (at a rate of roughly 1 code per second).

Press the P+ , G or B key once again to slow

down the test speed (1 code every 3 seconds). As

soon as the set changes channels (or turn off, or

start to play the disk), you must press OK to save

00131872bda.indd Abs1:2-Abs1:3

the code and stop the remote control scrolling

through the list. If you do not react quickly enough,

you can go back to the previous code by pressing

P- or E (DVD/VCR only) as many times as

necessary (you can go forward by pressing G ,

P+ or B (DVD/VCR only) if you have gone back

too far). As soon as the set responds again, press

OK to save the code.

Method E – Programming for control of a

COMBO (combined TV-VCR, TV/DVD, VCR/

DVD, ... set)

Depending on the COMBO group (TV/VCR, VCR/

DVD, etc.) and the make, you will be required to

enter a single code for both devices in the COMBO,

or to enter two codes, one code per device. Consult

the separate list to discover this. Before you start

programming, you must ﬁ nd the subcode or code

of the subset to be controlled (television or video

recorder...). Refer to the list supplied with this user

manual (see page subcodes or codes).

1. Switch on the COMBO you want to control.

2. Hold the SETUP key down until the red indicator

lamp blinks and then remains lit. Release the

SETUP key.

3. Press the key of the ﬁ rst device to control, and then

follow one of the programming methods A, B, C or

D previously described.

4. If a second code programming is required, then

repeat steps 2 and 3 above.

How to retrieve

a programmed code

It may be useful to retrieve the code programmed in

the remote control.

1. Hold down the SETUP key until the red indicator

light blinks and then remains lit. Release the SETUP

key.

2. Press the key that corresponds to the type of

equipment you want to control:

TV: television set, DVD: DVD player, Video

recorder, SAT: satellite receiver, cable, DVBT,

ADSL.

3. Press the SETUP key again brieﬂ y, the indicator

light blinks once.

4. Press the number keys (0 to 9) until you notice that

the indicator lamp blinks once.

5. The number which made the indicator lamp blink

is the ﬁ rst of the four ﬁ gures comprising your code,

write it down.

6. Repeat step 3 to ﬁ nd out the 3 other numbers of

the code.

7. When the fourth ﬁ gure is found, the indicator lamp

goes out.

Check of

the programming

For a television or a satellite receiver: switch on

and, for example, press 2 to change channels,

etc...

Video recorder: load a tape and then press B.

DVD player: load a DVD and then press B.

Try other remote control keys to ﬁ nd out the range of

functions you can control. If you think that not all of the

keys are active, try the programming Method B or C.

When you have retrieved the code of

your set, jot it down so that you can use it

whenever needed.

After battery replacement, you may have to

programme the remote control again.

TV CODE

DVD/SAT CODE

Other functions

Placing all devices on standby

Press the G key twice in less than one second, keeping

it held down the second time. All the devices go on

standby one after the other (the devices which were

already on Standby may turn on).

Adjustment of ALL volume controls under a

speciﬁ c mode

In its delivered state, the ROC6309 is programmed

such that all modes will use their own Volume and

Mute functions if present.

You can allocate the volume control to one of the

modes of the remote control on condition that the

volume control exists on the corresponding device

(e.g. control of TV sound in TV mode, DVD mode, VCR

Mode, etc.).

1. Hold the SETUP key down until the red indicator

lamp blinks and then remains lit.

2. Release the SETUP key

3. Press the H key until the red indicator lamp blinks

once.

4. Press once on the mode key (TV, DVD, ...)

corresponding to the device whose volume will

always be controlled by the VOL and H keys.

5. Press the H key once. The red indicator lamp goes

off.

6. All other mode will now punch-through to your

chosen mode for Volume and Mute control.

Adjustment of the volume controls for EACH

mode.

You can decide that the volume control is functional

for each mode selected on condition that the volume

control exists on the corresponding device (e.g. control

of the television set sound in TV mode, the control of

the sound of the SAT receiver in SAT mode, ...).

1. Hold the SETUP key down until the red indicator

lamp blinks and then remains lit.

2. Release the SETUP key

3. Press the H key until the red indicator lamp blinks

once.

4. Press once on the mode key (TV, DVD, ...)

corresponding to the device whose volume will

always be controlled by the VOL and H keys.

5. Press the VOL- key once.

6. Press the H key once. The red indicator lamp goes

off.

7. The chosen mode key will now use its own Volume

and Mute functions

Restoring the universal Volume/Mute

functions

If you have changed the universal volume and mute

functions, as described in the previous two sections,

you can reset the functions back to the factory settings:

1. Hold the SETUP key down until the red indicator

lamp blinks and then remains lit.

2. Release the SETUP key

3. Press the H key until the red indicator lamp blinks

once.

4. Press and release the H key. The red indicator

lamp will go off completely. The volume and mute

functions are now restored to their factory defaults.