TO THE OWNER: Read this manual before operating your Woods equipment. The information presented will prepare you to do a better and safer job. Keep this manual handy for ready reference. Require all operators to read this manual carefully and become acquainted with all adjustment and operating procedures before attempting to operate.
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! ■ Power unit must be equipped with ROPS or ROPS cab and seat belt. Keep seat belt secure- Safety is a primary concern in the design and man- ly fastened. Falling off power unit can result in ufacture of our products.
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! ■ Watch for hidden hazards on the terrain during ■ Always wear relatively tight and belted clothing operation. to avoid getting caught in moving parts. Wear sturdy, rough-soled work shoes and protec- ■...
Replace safety decals if they are missing or illegible. Replacement safety decals can be ordered free from your Woods dealer. To locate your nearest dealer, check the Dealer Locator at www.WoodsEquipment.com, or in the United States and Canada call 1-800-319-6637.
Page 8
SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! 3 - PN 55121 4 - PN 1003751 WARNING CRUSHING AND PINCHING HAZARD Be extremely careful handling various parts of the machine. They are heavy and hands, fingers, feet, and other body parts could be crushed or pinched between tractor and implement.
OPERATION The operator is responsible for the safe operation of CONNECTING BOX SCRAPER this equipment. The operator must be properly trained. TO TRACTOR Operators should be familiar with the equipment, the tractor, and all safety practices before starting opera- tion. Read the safety rules and safety decals on page 5 through page 8.
Quick Hitch Connection SCARIFYING 1. Place the scarifier shanks in position with the points NOTICE facing toward the tractor. 2. Lock into position with the lock pins provided. The ■ The 3/4" bolt and sleeve in the lower hole pro- lower shank position provides the greatest ground vide the attachment point for a Category 1 quick penetration.
OWNER SERVICE The information in this section is written for operators who possess basic mechanical skills. If you need help, your dealer has trained service technicians available. For your protection, read and follow the safety informa- tion in this manual. WARNING ■...
■ Inspect machine and replace worn or damaged parts. ■ Sand down scratches and the edges of areas of missing paint and coat with Woods spray paint of matching color (purchase from your Woods dealer). Figure 7. Scarifier Point Replacement ■...
ASSEMBLY DEALER SET-UP INSTRUCTIONS Assembly of this Box Scraper is the responsibility of the WOODS dealer. It should be delivered to the owner completely assembled and adjusted for normal conditions. Complete the Checklists on page 15 before delivering the attachment to the customer.
DEALER CHECKLISTS DEALER PRE-DELIVERY CHECKLIST DEALER DELIVERY CHECKLIST (DEALER’S RESPONSIBILITY) (DEALER’S RESPONSIBILITY) Show customer the safe, proper procedures Inspect the equipment thoroughly after assembly to to be used when mounting, dismounting, and be certain it is set up properly before delivering it to storing equipment.
BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual parts list. Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware. Make sure fastener threads are clean and you start thread engagement properly.
BOLT SIZE CHART NOTICE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. SAE BOLT THREAD SIZES 5/16 10mm 12mm 14mm 16mm 18mm METRIC BOLT THREAD SIZES ABBREVIATIONS AG ....Agriculture HT .
Page 20
Woods logo are trademarks of Woods Equipment Company. All other ® trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual are the property of their respec tive companies or mark holders. Specifications subject to change without notice.