Related Manuals for Woods BS48.20
Summary of Contents for Woods BS48.20
- Page 1 BOX SCRAPERS BS48.20 BS60.20 BS72.20 BS60.30 BS72.30 BS72.40 BS84.40 MAN1377_2024-02.indd 1 MAN1377_2024-02.indd 1 2/29/24 9:00 AM 2/29/24 9:00 AM...
-
Page 2: Introduction
TO THE OWNER: Read this manual before operating your Woods equipment. The information presented will prepare you to do a better and safer job. Keep this manual handy for ready reference. Require all operators to read this manual carefully and become acquainted with all adjustment and operating procedures before attempting to operate. -
Page 3: Table Of Contents
TABLE OF CONTENTS INTRODUCTION..........2 WARRANTY INFORMATION . -
Page 4: Specifications
SPECIFICATIONS Model BS48.20 BS60.20 BS72.20 BS60.30 BS72.30 BS72.40 BS84.40 Tractor HP 20-35 25-45 40-65 Tractor Hitch Catergory Limited Cat 1/ Cat 1 Cat 1 Cat 1 / Cat 2 Working Width (in) Capacity, Heaped (cubic ft) 11.5 13.9 15.6 18.9 22.3... -
Page 5: Safety Rules
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! ■ Power unit must be equipped with ROPS or ROPS cab and seat belt. Keep seat belt secure- Safety is a primary concern in the design and man- ly fastened. Falling off power unit can result in ufacture of our products. -
Page 6: Transportation
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! TRANSPORTATION ■ Look down and to the rear and make sure area is clear before operating in reverse. ■ Always comply with all state and local lighting ■ Use extreme care when working close to fences, and marking requirements. -
Page 7: Storage
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! ■ Never perform service or maintenance with en- gine running. ■ Keep all persons and animals away from oper- ator control area while performing adjustments, service, or maintenance. ■ Eye protection must be used when removing or installing scarifier shank clips. -
Page 8: Safety Decals
Replace safety decals if they are missing or illegible. Replacement safety decals can be ordered free from your Woods dealer. To locate your near- est dealer, check the Dealer Locator at www.WoodsEquipment.com, or in the United States and Canada call 1-800-319-6637. - Page 9 SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! 2 - PN 55121 5 - PN 1021069 6 - PN 1021070 DANGER DANGER DANGER FALLING OFF WILL RESULT IN BEING RUN OVER. n Tractor must be equipped with ROPS (or ROPS CAB) and seat belt.
-
Page 10: 10 Operation
OPERATION The operator is responsible for the safe operation of this equipment. The operator must be properly trained. Operators should be familiar with the equipment, the tractor, and all safety practices before starting opera- tion. Read the safety rules and safety decals on page 5 through page 9. - Page 11 BSXX.30 Models 3. When using a Category 1 Quick Hitch, install sleeve (6) on inner clevis of lower hitch bracket and secure with klik pin. CATEGORY 1 TOP LINK 4. Quick Hitch attaches to lower hitch pin sleeves and CONNECTION sleeve between mast plates.
-
Page 12: Adjusting Top Link
ADJUSTING TOP LINK BACKFILLING 1. Raise or remove scarifier shanks. The box scraper is leveled by adjusting the length of the tractor’s top link. 2. Lower the scraper to the ground and back up into the fill material. ● Shortening the top link will deepen the scarifier tooth penetration. -
Page 13: Owner Service 13
OWNER SERVICE The information in this section is written for operators who possess basic mechanical skills. If you need help, your dealer has trained service technicians available. For your protection, read and follow the safety informa- tion in this manual. WARNING ■... -
Page 14: Replacing Cutting Edge
■ Sand down scratches and the edges of areas of or replace it if both edges have been used. missing paint and coat with Woods spray paint of matching color (purchase from your Woods 4. Attach cutting edge to box scraper and secure with dealer). -
Page 15: Assembly 15
DEALER SET-UP INSTRUCTIONS CAUTION Assembly of this Box Scraper is the responsibility of the WOODS dealer. It should be delivered to the owner com- ■ Always wear relatively tight and belted clothing pletely assembled and adjusted for normal conditions. to avoid getting caught in moving parts. Wear... - Page 16 1. SCRAPER FRAME 2. PLATE, MAST RT 3. PLATE, MAST LT W/ DECAL 9. SLEEVE, CAT 1 QUICK HITCH 21. HHCS, M16 X 2.0 X 50 CLASS 8.8 22. WASHER, 5/8 SAE FLAT HRDN 23. NUT, LOCK, 16MM CD9404 24. HHCS, M20 X 2.5 X 110 CLASS 8.8 25.
-
Page 17: Dealer Checklists 17
DEALER CHECKLISTS DEALER PRE-DELIVERY CHECKLIST DEALER DELIVERY CHECKLIST (DEALER’S RESPONSIBILITY) (DEALER’S RESPONSIBILITY) Show customer the safe, proper procedures Inspect the equipment thoroughly after assembly to to be used when mounting, dismounting, and be certain it is set up properly before delivering it to storing equipment. - Page 18 NOTES 18 Notes MAN1377 ( 02/29/2024 ) MAN1377_2024-02.indd 18 MAN1377_2024-02.indd 18 2/29/24 9:00 AM 2/29/24 9:00 AM...
-
Page 19: Parts 19
BS72.20 BS48.20, BS60.20, BS72.20 ......20 - 21 BS60.30, BS72.30 ....... . . 22 - 23 BS72.40, BS84.40 . - Page 20 BS48.20, BS60.20, BS72.20 CD9397 20 Parts MAN1377 ( 02/29/2024 ) MAN1377_2024-02.indd 20 MAN1377_2024-02.indd 20 2/29/24 9:00 AM 2/29/24 9:00 AM...
- Page 21 BS48.20, BS60.20, BS72.20 PARTS LIST BS48.20 BS60.20 BS72.20 QTY DESCRIPTION SCRAPER FRAME 645142 ----- ----- BAR, A-FRAME RT BS48.20 W/ DECAL ----- 645138 645138 BAR, A-FRAME RT BS60.20, BS72.20 W/ DECAL 645143 ----- ----- BAR, A-FRAME LT BS48.20 W/ DECAL...
- Page 22 BS60.30, BS72.30 CD9398 22 Parts MAN1377 ( 02/29/2024 ) MAN1377_2024-02.indd 22 MAN1377_2024-02.indd 22 2/29/24 9:00 AM 2/29/24 9:00 AM...
- Page 23 HHCS, M20 X 2.5 X 110 CLASS 8.8 ----- ----- WASHER, FLAT 20MM ----- ----- NUT, LOCK, 20MM 78760 78760 DECAL, MODEL, WOODS WHITE 1.52 X 8.00 642651 642652 DECAL, MODEL BSXX.30 DECAL, MODEL, BSXX.30 FOR 642836 642837 MASSEY FERGUSON STANDARD HARDWARE, OBTAIN LOCALLY...
- Page 24 BS72.40, BS84.40 CD9399 24 Parts MAN1377 ( 02/29/2024 ) MAN1377_2024-02.indd 24 MAN1377_2024-02.indd 24 2/29/24 9:00 AM 2/29/24 9:00 AM...
- Page 25 HHCS, M20 X 2.5 X 110 CLASS 8.8 ----- ----- WASHER, FLAT 20MM ----- ----- NUT, LOCK, NUT 20MM 78760 78760 DECAL, MODEL, WOODS WHITE 1.52 X 8.00 642653 642654 DECAL, MODEL BSXX.40 DECAL, MODEL, BSXX.40 FOR 642838 642839 MASSEY FERGUSON STANDARD HARDWARE, OBTAIN LOCALLY...
-
Page 26: Appendix
BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual parts list. Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware. Make sure fastener threads are clean and you start thread engagement properly. -
Page 27: Bolt Size Chart & Abbreviations
BOLT SIZE CHART NOTICE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. SAE BOLT THREAD SIZES 5/16 10mm 12mm 14mm 16mm 18mm METRIC BOLT THREAD SIZES ABBREVIATIONS AG ....Agriculture HT . - Page 28 Woods logo are trademarks of Woods Equipment Company. All other ® trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual are the property of their respec tive companies or mark holders. Specifications subject to change without notice.