Table of Contents
Advertisement
English
nOTE: The light will not time out until the entire unit
times out.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off, remove the battery pack
and disconnect it from the power source before
making any adjustments or removing/installing
attachments or accessories. An accidental start-up
can cause injury.
Hose and Accessory Storage (Fig. A)
12V DC Vehicle Connector and Cord
•
The 12V DC vehicle connector
the storage compartment on the side of the inflator.
high-Pressure hose
•
The high-pressure hose
channel on the side of the unit. Wrap the high-pressure
hose inside the channel and secure in the provided clips.
high-Volume hose
•
The high-volume hose
channel on the side of the unit. Wrap the high-volume
hose inside the channel and secure in the two clips.
Accessories
•
The accessories
,
15
clips located on the side of the inflator.
Fitting the Accessories (Fig. A)
The high-volume hose
5
tapered nozzle
.
13
The high-pressure hose
10
attachments which can be found on the side storage panel:
•
an inflation needle
16
•
a high-pressure tapered nozzle
•
a Presta valve adapter
nOTE: Make sure each of these adapters is firmly locked in
place before turning on the inflator.
Fitting the High-Volume Hose (Fig. D)
•
Remove the high-volume hose
storage location.
•
Line up the notches of the hose with the nubs
high volume pump outlet/inflation port
the hose on and twist counter-clockwise to secure.
•
To remove, twist the hose clockwise and slide hose off.
Many inflatables have an internal flap that prevents air loss
during inflation, especially air mattresses. Unless this flap is
displaced by the nozzle the inflatable will not inflate. Push
the nozzle firmly into the valve to make sure that you push
this flap out of the way.
8
19
can be stored inside
10
is located on a storage
is located on a storage
5
and
are stored in snap
16
17
comes fitted with a standard
can be fitted with the following
,
, and
15
17
.
5
from its
21
18
. Then, slide
Fig. D
Pressure Calibration
The pressure sensor can be re-calibrated for use in high
elevations (recommended over 5000 ft [1524 m]).
nOTE: Calibration will not be stored when the inflator is
OFF. Every time the inflator is turned on, it will be reset to sea
level calibration.
To re-calibrate, the inflator must have a battery installed or it
must be plugged into a power source.
1. Make sure inflator is OFF.
2. Make sure the high-pressure hose is not connected
to anything. Pressure in the hose will disable
the calibration.
3. Press and hold the LED light switch
the LED light switch, press the power switch
and release.
4. Keep holding the LED light switch for 5 seconds.
5. When the calibration sequence is complete, the
pressure display will flash and then display "0.0".
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off, remove the battery pack
and disconnect it from the power source before
making any adjustments or removing/installing
attachments or accessories. An accidental start-up
can cause injury.
Installing and Removing the Battery Pack
(Fig. E)
of the
nOTE: For best results, make sure your battery pack is
fully charged.
To install the battery pack
battery pack with the rails inside inflator's battery port and
slide it into the port until the battery pack is firmly seated
and ensure that it does not disengage.
To remove the battery pack from the tool, press the release
button
and firmly pull the battery pack out of the tool
11
handle. Insert it into the charger as described in the charger
section of this manual.
nOTE: The inflator will not charge batteries.
21
18
. While holding
3
2
12
into the inflator, align the
5
Advertisement
Table of Contents
