Table of Contents
Advertisement
Operating instructions
Setting the current time
1. Confirm that the DIGITAL FREQUENCY COUNTER
is in
the time display mode.
When the DIGITAL FREQUENCY COUNTER is in the fre-
quency display mode, press the POWER switch.
2. Press the ADJUST button.
The hour display of the left starts flashing.
When the station name is not displayed.
3. Input the current time using the PRESET buttons (1 to 0).
The clock employs 24-hour system.
Press the PRESET
buttons as follows.
AM
93:05
Input in the order of
0o-9-0-5
PM
4:50
Input in the order of
1-6-5-0
When 4 digits are input, the entire time display flashes.
To change the input digit, press the CLEAR button and
proceed the above steps again.
4. Press the ENTER button
{6 5 Hii
The time display illuminates.
:
Iiluminates.
When the ENTER button is pressed, the clock starts.
Press the ENTER button according to the time signal of
the radio or telephone service.
Note:
. When the time display flashes, this indicates the power failure oc-
curred. At that time, reset the current time.
Listening to broadcasts
Auto tuning.
1. Press the POWER switch.
2. Set the input mode of the amplifier to tuner.
3. Select the reception band with the band selector buttons.
4. Press the TUNING MODE button so that the AUTO indi-
'
gator lights.
5. Press UP or DOWN side of the TUNING button.
The unit starts scanning in the specified direction and
stops at a station with a sufficient signal strength.
6. Adjust the volume control of the amplifier.
Manual tuning
. Press the POWER switch.
. Set the input mode of the amplifier to tuner.
. Select the reception band with the band selector buttons.
. Press the TUNING MODE button so that the AUTO indi-
cator disappears.
In the FM band, the MONO
indicator
lights.
5. Press UP or DOWN
side of the TUNING button until the
desired station is received.
When the TUNING button is kept pressed, the displayed
frequency changes rapidly.
;
6. Adjust the volume control of the amplifier.
ON
Direct station tuning
1. Press the DISPLAY button to set the display window to
the frequency mode.
Select the desired
band with the band select butotn
(AM/FM).
3. While the frequency indicator is displayed, press the DIR-
ECT button.
8
KT-76/KT-550L (kK)
5. When the input frequency is within the range of the band,
the station of the input frequency is received immediately
after the final column is input. ~
if the input frequency is out of the range of the band, the
frequency indicator flashes for 5 senconds and error indi-
cation is displayed, then the display mode before press-
ing the DIRECT button resumes.
6. During inputting the frequency, when the incorrect PRE-
SET buttons is pressed by mistake and is noticed, press
the CLEAR button to return to the standby mode for the
first column input.
Presetting stations
With the station name displayed, a total of 12 stations can
be preset, and with the station name not displayed, a total of
20 stations can be preset for AM or FM broadcast. (Select
the number of preset stations with the STATION
NAME
AND PRESET select switch located on the rear panel of the
tuner.)
1. Press the DISPLAY button to set the display to the fre-
quency display mode.
2. Press the AM or FM band select key.
3. Receive the desired station to be memorized
with the
TUNING button or DIRECT tuning function.
At this time, input the station name if required, referring
to "Station Name Indication" on page 9. (This operation
is possible after memorizing the frequency.)
4. Press the ENTER button.
"MEMORY" displays in the display window.
5. Select the A or B preset group with the PRESET A/B
switch.
When this is not done, the preset group which is current-
ly indicated is selected.
6. Within 5 seconds, press any of 1 to 6 numeric keys
(when the station name is displayed) or 1 to O keys (when
- the station name is not displayed).
The MEMORY
indicator in the display window goes off
and the preset indiator will light.
In the same way, preset the other stations. When preset-
ting the station into the "10" preset indicator, press the
"Q" preset button.
STATION
NAME AND PRESET switch located on the
rear panel of the tuner
(cm: When the station name is not displayed (10 stations
for each A and B)
mI:
When
the station name
is displayed (6 stations for
each A and B)
STATION
RAME
PRESET
2
Ua
—
4
PRESET =|
20
Note:
1. When the station is memorized into the preset number in which
another station has been preset, the previously-preset station
will be cleared and the newly-preset station will be memorized.
Be sure to press the preset button (1 to O) after releasing the
ENTER key.
If the preset button (1 to 0) is pressed while the ENTER key is
pressed, the same frequency may also be memorized
into the
-
other preset button.
a
a
a
Advertisement
Table of Contents
