Page 1: Table Of Contents
4000E IP Broadband Loop Carrier Installation Instructions Document Number IPD4-A2-ZZ40-20 October 2005 Contents End User License Agreement (Zhone and Affiliates) Introduction Unpacking and Inspecting the Equipment Installation Options Installing Your Management Module Installing Your Interface Module(s) Powering Up Your 4000E BLC...
Page 2: End User License Agreement (Zhone And Affiliates)
Zhone from time to time to control access to or limit use of the Software; (d) sublicensed, rented, leased or lent to third parties; (e) imported or exported into any jurisdiction except in compliance with all applicable laws of the United States and such jurisdiction;...
Page 3 Software. You may provide written notice of such defect (addressed to Zhone Technologies, Inc., Attention: Customer Service, 7001 Oakport Street @ Zhone Way, Oakland, CA 94621) no later than ten (10) days following expiration of such period and, as your sole and exclusive remedy, Zhone will provide replacement media.
Page 4: Introduction
IP Ethernet foundation for a variety of feature-rich multi-service access mulitplexer modules. The 4000E BLC features a high capacity backplane delivering up to 8 Gbps throughput, and providing a non-blocking architecture for even the highest bandwidth broadband access technologies, such as ADSL2+. It supports a...
Page 5: Unpacking And Inspecting The Equipment
The following components should be included in the shipping container: 1 – 4000E BLC with 1 fan module and 12 slot covers 4 – Rubber Bumper Screws 2 – Rack Mount Brackets (either 19" or 23", as ordered) 10 –...
Page 6: Installation Options
Installation on a Tabletop 4000E IP Broadband Loop Carrier Installation Instructions The 4000E BLC is designed for installation in a Restricted Access area where admittance is limited to trained and authorized service personel. It may be installed on a tabletop or in a rack.
Page 7 Using a Phillips Screwdriver, attach the two provided rack mount brackets to the sides of the 4000E with eight of the ten provided bracket screws. There are seven position options for the rack brackets; position them as best suited to the space available for your chassis on the rack being utilized.
Page 8: Installing Your Management Module
An uplink module provides the upstream network connection for the 4000E BLC; a management module cannot function without one. Depending on the management module model that you plan to install in your 4000E, you will need either a Media Interface Module (MIM) or an Uplink Interface Module (UIM).
Page 9: Installing Your Interface Module(S)
Installing Your Interface Module(s) Interface modules provide the subscriber connections for a 4000E BLC; up to four interface modules may be installed in the 4000E (in slots 1–4). There are a variety of models available. Contact your sales representative. Any...
Page 10: Powering Up Your 4000E Blc
4000E as outlined in the following sections. Do not operate the 4000E without a ground connection. 1 Connect a ground wire to the 4000E: Line up the 2-hole terminal lug of your ground wire with the two holes on the small, unpainted section on...
Page 11 Central Office is grounded to a common copper bus. 3 Select a Terminal Block. Either terminal block on the back of the 4000E may be used to power the chassis; only one terminal block is required for operational purposes.
Page 12 "Return" terminal on your DC power supply. CAUTION: Observe proper polarity. The power source(s) connected to the 4000E must be equipped with a disconnect device such as an On/Off switch. Otherwise, an appropriately rated circuit breaker must be installed on each power circuit to be used.
Page 13: Uplink Connections
No configuration is necessary for Uplink Interface Modules (UIMs) or Media Interface Modules (MIMs) installed on the management module in your 4000E to operate at default settings. However, if you wish to run your uplink connections at settings other than the UIM or MIM defaults, configure the UIM or MIM prior to making a connection.
Page 14 RJ21 ports are directly behind each slot on the back of the chassis (1–4, bottom to top). Each interface module slot on the 4000E has two corresponding RJ21 connectors on the back of the chassis: the RJ21 connectors on the left (A) provide the subscriber connections for interface module ports 1–24 (on most models) and the...
Page 15 RJ21 connector frame on the chassis. Note: If you are using a 120 or 180 degree cable, both the right and left sides of the cable connector should be screwed to the RJ21 connector frame on the chassis. IPD4-A2-ZZ40-20 4000E IP Broadband Loop Carrier Installation Instructions Subscriber Lines...
Page 16: Securing The Connecting Cables
Network Management System (NMS). 4000E management capabilities depend upon the management module model installed in your chassis. Once the management module has been initialized, the interface modules installed in your 4000E may also be configured as desired. Refer to the following for further information: Table 1:...
Page 17: Fan Module
CAUTION: Do not operate the 4000E without a fan module or with a fan module that is not functioning properly. IPD4-A2-ZZ40-20...
Page 18: Specifications
Specifications 4000E IP Broadband Loop Carrier Installation Instructions Table 2: Specifications Specification Criteria Environment Operating Temperature: –40° F to 149° F (–40° C to 65° C) Storage Temperature: –40° F to 158° F (–40° C to 70° C) Humidity: 5 % to 95 %, non-condensing Altitude: –200 ft to 16,500 ft (–60 m to 5,000 m)
Page 19: Important Safety Instructions
12 In addition, if the equipment is to be used with telecommunications circuits, take the following precautions: — Never install telephone wiring during a lightning storm. IPD4-A2-ZZ40-20 Important Safety Instructions ) fixed power source wires with strain 4000E IP Broadband Loop Carrier Installation Instructions...
Page 20: Emi Notices
EMI Notices 4000E IP Broadband Loop Carrier Installation Instructions — Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. — Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.
Page 21: Notice To Users Of The Canadian Telephone Network
When the product is marked with the CE mark on the equipment label, a supporting Declaration of Conformity may be downloaded from the www.zhone.com website. Product Documentation Online Complete documentation for this product is available at www.zhone.com. IPD4-A2-ZZ40-20 Notice to Users of the Canadian Telephone Network 4000E IP Broadband Loop Carrier Installation Instructions...
Page 22: Contacting Global Service And Support
Service Requirements 4000E IP Broadband Loop Carrier Installation Instructions Contact Global Service and Support (GSS) if you have any questions about this or other Zhone products. Before contacting GSS, make sure you have the following information: Zhone product you are using...

Zhone 4000E Installation Instructions Manual

Quick Links

Related Manuals for Zhone 4000E

Summary of Contents for Zhone 4000E

Table of Contents