Table of Contents
Advertisement
LT2000 QuickSet Programmer
Use the Zenith LT2000
QuickSet II "Clone"
Programmer to copy the
setup from a "master" TV
then quickly transfer the
setup to duplicate TVs -
must be the same model
number as the master TV
THE CLONE HAS CONTROL OF THE TV
THE CLONE IS VERSION
THE TV IS VERSION
THE SW IS REVISION
CLONE CLOCK
= XX:XX
TV
CLOCK
= XX:XX
-PRESS ANY KEY TO CONTINUE.
-DISCONNECT CLONE WHEN DONE.
Clone Controlling TV Display
The optional QuickSet II Clone Programmer (LT2000) allows custom setup and programming information to be quickly copied from a mas-
ter TV into multiple identical television sets. Once learned from the master, setup data is retained in the LT2000 for future use.
When using the LT2000, cloning operations will go easier if the TV set is connected to a good quality signal and operating with a stable
picture displayed. To operate the LT2000, use the indicated keys on the LP702 remote, or the front panel keys on the TV receiver.
Before you begin...
• The "master TV" should be connected to a good, stable signal
from an over-the-air antenna or cable service and turned on.
• Teaching and Learning is only possible between identical model
Zenith TVs. (However, the Clone programmer can store 4 different
master TV setups.)
WARNING: Copying a blank or incorrect memory into a TV
will cause the TV to operate erratically or become inoper-
able.
• Use a Zenith Remote like the LP702 or the TV front panel con-
trols to operate Learning and Teaching menus.
• Make sure that the batteries in the Clone programmer are fresh.
• If the batteries are removed, the Clone Clock time will be lost.
• Decide if you want to set the time from the Clone programmer or
copy the time to the Clone programmer; from a TV which has the
clock set to the current time.
• Follow the connection diagrams above to connect the Clone to a
master TV and, after learning is complete, to another TV to "teach"
it the setup.
A slow flashing green light indicates there is a problem with the communications between the TV and the programmer. In this case,
check for a damaged cable, poor contacts, or other connection troubles.
If the status indicator is red, the programmer batteries are low and should be replaced. Use 4 good-quality alkaline AA batteries.
206-3492-O
Learn
Master TV
Typical MPI Connections
Antenna
RF coaxial wire
(75ohm)
XX
XX
XX
Teach
Typical MPI Connections
TV back
LEFT
RIGHT
COMPUTER
ANTENNA
AUDIO INPUT
CABLE
R- AUDIO- L
S-VIDEO
INPUT
LOOP OUT - S-VHS - IN
M.P.I.
AUX
INPUT
VIDEO
R -AUDIO- L
®
QuickSet II Programmer
LT2000
Clone
• Setting the time and transferring it to the Clone or another TV is
a separate procedure.
• Once a TV's setup is copied to another TV, that TV needs to be
disconnected from power for about 5 seconds to activate the
newly copied setup.
• See Troubleshooting to solve problems.
A. Set Up a Master TV
Using a Zenith remote like the LP702, set up a "master" TV with
custom settings and features as described in the master TV's oper-
ating guide. The master TV's Setup is what you will copy to the
Clone Programmer and transfer to TVs of the same model so they
will operate identically.
B. Connect Clone to Master TV
If there is a good connection, the "Clone has Control of TV" mes-
sage will appear. (See menu above.)
Other TV
TV back
Antenna
RIGHT
COMPUTER
RF coaxial wire
ANTENNA
AUDIO INPUT
CABLE
(75 ohm)
S-VIDEO
INPUT
LOOP OUT - S-VHS - IN
M.P.I.
AUX
INPUT
VIDEO
R -AUDIO- L
®
QuickSet II Programmer
LT2000
Clone
P A G E 1 7
LEFT
R- AUDIO- L
Advertisement
Table of Contents
