Related Manuals for Zenith C27F33
Summary of Contents for Zenith C27F33
- Page 1 Installation and Operating Guide | Warranty Model Numbers | C27F33 • C32F33 | Direct View TVs © Copyright 2002, Zenith Electronics Corporation.
-
Page 2: Safety Warnings
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. CAUTION: Do not attempt to modify this product in any way without written authorization from Zenith Electronics Corporation. Unauthorized modification could void the user’s authority to operate this product. -
Page 3: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS Important safeguards for you and your new product Your product has been manufactured and tested with your safety in mind. However, improper use can result in potential electrical shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read and observe the following safety points when installing and using your new product, and save them for future reference. - Page 4 IMPORTANT SAFETY INSTRUCTIONS (Continued from previous page) 14. Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code (U.S.A.), ANSI/ NFPA 70 provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-...
-
Page 5: Table Of Contents
Connection of external equipment ...25 Connecting a DVD player ...27 Product Specifications ...28 Maintenance ...29 Troubleshooting Checklist ...30 Your Zenith Limited Warranty ...Back cover Step 3 Set up the individual features, picture, and sound to your personal preference. :See appropriate pages... -
Page 6: Remote/Front Panel Controls
This is a simplified representation of front panel. on/off MUTE Press to mute sound. Press again to restore sound. 2. POWER(or ON/OFF) Refer to "Turning the TV On/Off". 3. NUMBER Direct channel selection. 4. CAPTION Selects CAPTION mode. Refer to "Closed captions". -
Page 7: Installing Batteries In The Remote Control
Selects favorite channels. Refer to "Favorite channel memory". Selects the sound appropriate for the program's character ; Illuminates red when the TV is in standby mode. Refer to "Turning the TV On/Off".. damage the remote control. Do not mix old and new batteries or different types of batteries (for example, standard and alkaline). -
Page 8: Basic Tv Setup And Operation
Basic TV Setup and Operation Before operating your TV, make sure the following have been completed. • Your TV is connected to an antenna or a cable system. • Your TV is plugged into a standard power outlet. Turning the TV On/Off The set switches to standby mode and the standby indicator lights up in red. -
Page 9: Channel Search
There are two ways of memorizing channels. You can use either. One is AUTO PROGRAM and the other is MANUAL PROGRAM. In AUTO PROGRAM, the TV memorizes the channels in ascending numerical order. If there are additional channels you want to add or delete, add or delete them manually. -
Page 10: Memorizing The Channels With Manual Program
Basic TV Setup and Operation Memorizing Channels with Manual Program Using Memory/Erase button MANUAL PROGRAM the TV using the convenient memory/erase button on the remote control. 1. Use the or NUMBER buttons to select the channel number you want to memorize or erase. -
Page 11: Available Features
6. Press the menu button to remove menu. Setting the Off Timer Off Timer automatically switches the TV to standby mode at the preset time. 1. Press the menu button and then use menu shown to the right. -
Page 12: Setting The On Timer
6. Press the menu button to remove menu. Notes • If you don’t press any button within 2 hours after turning on the TV with the ON TIMER function, the TV will automatically switch back to standby mode. -
Page 13: Operating Degauss
• If are unable to correct problem by degaussing, try again after about 4 minutes. Key Lock The TV can be set up so that the remote control is needed to operate it. This feature can be used to prevent unauthorized viewing. 1. Press the menu button and then use menu shown to the right. -
Page 14: Picture Tilt
Available Features Picture Tilt The picture on the TV screen may tilt to left or right if the TV is moved to another direction. Picture Tilt can be used to correct any uneven picture tilt. 1. Press the menu button and then use menu shown to the right. -
Page 15: Picture Control
3. Press the enter ( ) button to remove menu. VM (Velocity Modulation) If you select , the TV will automatically enhance the sharpness of the image's edges. 1. Press the menu button and then use menu shown to the right. -
Page 16: Adjusting The Picture
Picture Appearance Control Adjusting the Picture Appearance This is the function to manually adjust the desired picture levels: preference. If the picture settings you adjust are not satisfactory, you can also select a factory preset picture setup. 1. Press the menu button and then use menu shown to the right. -
Page 17: Sound Control
2. Press the enter ( ) button. Notes • Stereo or SAP can only be received when the TV station transmits those signals, even though you have selected • Mono sound is automatically received if the broadcast is only in Mono;... -
Page 18: Adjusting Equalizer (Off Mode In Asc)
Sound Control Adjusting the Equalizer (User Mode In ASC) 1. Press the menu button and then use menu shown to the right. 2. Press the and then use button to select 3. Use the button to select the 4. Use the button to select the sound band and then use the button to select the desired level. -
Page 19: Adjusting The Bass
Adjusting Bass This function is to increase or decrease bass. 1. Press the menu button and then use menu shown to the right. 2. Press the and then use button to select 3. Use the button to select 4. Use the button to select 5. -
Page 20: Closed Caption
• Not all TV broadcasts include closed caption signals. • Sometimes TV stations broadcast two different caption signals on the same channel. By selecting from CC 1 to CC 4, you can choose which signal you view. Mode 1 is usually the signal with the captions, while another mode 2 might show demonstration or programming information. -
Page 21: Operating The Caption And Text
3. Use the button to select 4. Press the menu button to remove menu. Note: This TV is programmed to remember which mode it was last set to, even if you turn the TV off. -
Page 22: Parental Control
Rating guidelines are provided by broadcast stations. Most television programs and television movies can be blocked by TV Rating and/or Individual Categories. Movies that have been shown at the theaters or direct-to-video movies use the Movie Rating System (MPAA) only. -
Page 23: Blocking Setup
Blocking Setup 1. Press the MENU button and then use menu shown to the right. 2. Press the and then use the 3. Press the button. If Parental is already set, enter the password when requested. Age block and Content block options, also have sub menus; repeat steps 3 to 4 in sub menu, to set type of blocking and rating. -
Page 24: Antenna Connections
If you subscribe to a CATV system, make the antenna connection as described below. 75 ohm Antenna Jack 1. Remove the 300 to 75 ohm adapter or the cable from the TV, if attached. 2. Connect the CATV cable (75 ohm coaxial cable) to the 75 ohm antenna jack. 75 ohm... -
Page 25: Connection Of External Equipment
5. §/ EARPHONE JACK Note: This TV is programmed to remember which mode it was last set to, even if you turn the TV off. Connecting AUDIO/VIDEO IN Jacks 1. Connect the audio/video output jacks of the VCR to IN 1 or IN 2(A/V) jacks on the back of TV. - Page 26 1. Connect the output jacks of the playback VCR to the IN 1 or IN 2 (A/V) jacks on the back of the TV (or IN 3 jacks on the side of TV ). 2. Connect the input jacks of the recording VCR to the OUT (A/V) jacks on the back of the TV.
-
Page 27: Connecting A Dvd Player
DVD Player Connection and Setup • Connect component video inputs to Y, P • Note: This TV is programmed to remember which mode it was last set to, even if you turn the TV off. 1. How to connect TV INPUT... -
Page 28: Product Specifications
Product Specifications Model C27F33 C32F33 Power requirements Television system Television channels Power consumption External antenna impedance Audio output Speaker outputs External input ports Horizontal size (inches) Height (inches) Thickness (inches) Weight (pounds) Horizontal size (inches) Height (inches) Thickness (inches) Weight (pounds) -
Page 29: Maintenance
Maintenance Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you will have with your new TV. Be sure to turn the power off and pull out the plug before you begin any cleaning. -
Page 30: Troubleshooting Checklist
Troubleshooting Checklist SYMPTOMS No power No picture or sound Poor picture but good sound Poor reception Lines in picture Ghosts (multiple images) Remote control does not work. Cannot tune desired channel. CHECK THESE THINGS Is power cord plugged in? Is television turned on? Check batteries in remote control. - Page 31 Notes...
- Page 32 Direct-View TV Limited Warranty - USA Zenith will repair or replace your product, at Zenith’s option, if it proves to be defective in material or workmanship under normal use, during the warranty period (“Warranty Period”) listed below, effective from the date (“Date of Purchase”) of original consumer purchase of the product.