Yamaha WF192 Online Manual page 53

1.2.8 Pan
Messages which control the stereo panning position of
each Part.
CNTRL# PARAMETER
10 Pan
A setting of 0 = extreme left position, and 127 = extreme
right position.
1.2.9 Expression
Messages which control intonation expression of each
Part.
CNTRL# PARAMETER
11 Expression
A setting of 0 = minimum expression volume, and 127 =
maximum expression volume.
1.2.10 Control Change 13
CNTRL# PARAMETER
13 Control Change 13
Effective only for S-VA voices.
1.2.11 Hold1
Messages which control sustain on/off.
CNTRL# PARAMETER
64 Hold1
Settings between 0-63 = sustain off, and settings
between 64-127 = sustain on.
1.2.12 Portamento
Messages which control portamento on/off.
CNTRL# PARAMETER
65 Portamento
Settings between 0-63 = portamento off, and settings
between 64-127 = portamento on.
The parameter 1.2.5 Portamento Time controls the
portamento speed.
1.2.13 Sostenuto
Messages which control sostenuto on/off.
CNTRL# PARAMETER
66 Sostenuto
Holding specific notes and then pressing and holding the
sostenuto pedal will sustain those notes as you play
subsequent notes, until the pedal is released.
Settings between 0-63 = sostenuto off, and settings
between 64-127 = sostenuto on.
Ineffective for S-VA voices.
1.2.14 Soft Pedal
Messages which control soft pedal on/off.
CNTRL# PARAMETER
67 Soft Pedal
Notes played while holding the soft pedal will be
dampened. Settings between 0-63 = soft pedal off, and
settings between 64-127 = soft pedal on.
1.2.15 Harmonic Content
Messages which adjust the resonance set for each
Voice.
DATA RANGE
0...127
DATA RANGE
0...127
DATA RANGE
0...127
DATA RANGE
0...127
DATA RANGE
0...127
DATA RANGE
0...127
DATA RANGE
0...127
53
CNTRL# PARAMETER
71 Harmonic Content
The value set here is an offset value which will be added
to or subtracted from the Voice data.
Higher values will result in a more resonant sound.
Depending on the Voice, the effective range may be
narrower than the range available for adjustment.
1.2.16 Release Time
Messages which adjust the envelope release time set for
each Voice.
CNTRL# PARAMETER
72 Release Time
The value set here is an offset value which will be added
to or subtracted from the Voice data.
1.2.17 Attack Time
Messages which adjust the envelope attack time set for
each Voice.
CNTRL# PARAMETER
73 Attack Time
The value set here is an offset value which will be added
to or subtracted from the Voice data.
1.2.18 Brightness
Messages which adjust the filter cutoff frequency set for
each Voice.
CNTRL# PARAMETER
74 Brightness
The value set here is an offset value which will be added
to or subtracted from the Voice data.
Lower values will result in a softer sound.
Depending on the Voice, the effective range may be
narrower than the range available for adjustment.
1.2.19 Portamento Control
Messages which apply a portamento between the
currently sounding note and the subsequent note.
CNTRL# PARAMETER
84 Portamento Control
Portamento Control is transmitted specifying the Note On
Key of the currently-sounding note.
Specify a Portamento Source Key number between 0-
127.
When a Portamento Control message is received, the
currently sounding pitch will change with a Portamento
Time of 0 to the next Key On key on the same channel.
For example, the following settings would apply a
portamento from note C3 to C4.
90 3C 7F C3 = Key On
B0 54 3C Source Key number set to C3
90 48 7F C4 = Key On (When C4 = on, C3 is
raised by a portamento to C4.)
Even if the Multi Part parameter Rcv PORTAMENTO
(Table 1-4) = OFF, the Portamento Control message will
be received.
Ineffective for S-VA voices.
DATA RANGE
0...127 (0 : -64, 64 : +0, 127 : +63)
DATA RANGE
0...127 (0 : -64, 64 : +0, 127 : +63)
DATA RANGE
0...127 (0 : -64, 64 : +0, 127 : +63)
DATA RANGE
0...127 (0 : -64, 64 : +0, 127 : +63)
DATA RANGE
0...127