Midi Data Table - Yamaha MOTIF RACK Data List

(3-5) SYSTEM REAL TIME MESSAGES
(3-5-1) ACTIVE SENSING
STATUS 11111110(FEH)
Transmitted every 200 msec.
Once this code is received, the instrument starts sensing. When no status nor data is received for over
approximately 350 ms, MIDI receiving buffer will be cleared, and the sounds currently played and the sustain
switch are forcibly turned off. In this case, each control data will be reset to a certain value.
(3-6) SYSTEM EXCLUSIVE MESSAGE
(3-6-1) UNIVERSAL NON REALTIME MESSAGE
(3-6-1-1) GENERAL MIDI MODE ON
F0H 7EH 7FH 09H 01H F7H
Received only when SYSTEM Receive GM/XG on is set to on in MULTI MODE.
The Part values will be reset according to the SYSTEM Internal Part settings.
(3-6-1-2) IDENTITY REQUEST (Receive only)
F0H 7EH 0nH 06H 01H F7H
("n" = Device No. However, this instrument receives under "omni.")
(3-6-1-3) IDENTITY REPLY (Transmit only)
F0H 7EH 7FH 06H 02H 43H 00H 41H ddH ddH 00H 00H 00H 7FH F7H
dd: Device Number Code
MOTIF-RACK: 58 04
(3-6-2) UNIVERSAL REALTIME MESSAGE
(3-6-2-1) MIDI MASTER VOLUME
F0H 7FH 7FH 04H 01H llH mmH F7H
Sets the MASTER VOLUME value.
The value "mm" is used to set the master volume (the value "ll" should be ignored).
(3-6-3) PARAMETER CHANGE
(3-6-3-1) XG SYSTEM ON
11110000 F0
01000011 43
0001nnnn 1n
01001100 4C
0aaaaaaa 0
0aaaaaaa 0
0aaaaaaa 7E
0 0
11110111 F7
Received only when SYSTEM Receive GM/XG on is set to on in MULTI MODE.
Be aware that executing this message takes about 170 ms and that, therefore, a certain interval before executing
the following message is needed.
(3-6-3-2) NATIVE PARAMETER CHANGE, MODE CHANGE
11110000 F0
01000011 43
0001nnnn 1n
01101111 6F
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
0ddddddd ddddddd
| |
11110111 F7
For parameters with data size of 2 or more, the appropriate number of data bytes will be transmitted.
See the following MIDI Data Table for Address.
(3-6-4) BULK DUMP
11110000 F0
01000011 43
0000nnnn 0n
01101111 6F
0bbbbbbb bbbbbbb
0bbbbbbb bbbbbbb
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
0 0
| |
0ccccccc ccccccc
11110111 F7
See the following MIDI Data Table for Address and Byte Count.
The Check sum is the value that results in a value of 0 for the lower 7 bits when the Byte Count, Start Address, Data
and Check sum itself are added.
Bulk Dump data of the MOTIF (Model ID=0x6B) can be received.
(3-6-5) DUMP REQUEST
11110000 F0
01000011 43
0010nnnn 2n
01101111 6F
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
11110111 F7
See the following MIDI Data Table for Address and Byte Count.
Exclusive status
YAMAHA ID
Device Number
Model ID
Address High
Address Mid
Address Low
Data
End of Exclusive
Exclusive status
YAMAHA ID
Device Number
Model ID
Address High
Address Mid
Address Low
Data
End of Exclusive
Exclusive status
YAMAHA ID
Device Number
Model ID
Byte Count
Byte Count
Address High
Address Mid
Address Low
Data
Check-sum
End of Exclusive
Exclusive status
YAMAHA ID
Device Number
Model ID
Address High
Address Mid
Address Low
End of Exclusive
(3-6-6) PARAMETER REQUEST
11110000 F0
01000011 43
0011nnnn 3n
01101111 6F
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
0aaaaaaa aaaaaaa
11110111 F7
See the following MIDI Data Table for Address.
45
Exclusive status
YAMAHA ID
Device Number
Model ID
Address High
Address Mid
Address Low
End of Exclusive