Do not operate the crown or buttons while ー retailer or to an authorized CASIO service Example of Daily Use your watch is submersed in water or wet. center. Hand washing, rain Avoid wearing your watch while in the ー ...
Page 3
Watch Operation Guide 3552 Temperature Storage Leather Band ● ● ● Never leave your watch on the dashboard If you do not plan to use your watch for a Allowing your watch to remain in contact ● ● ● of a car, near a heater, or in any other...
Note that CASIO Computer Co., Ltd. watch and band free of dirt, sweat, water and the oxidization layer on the metal surface assumes no responsibility for any damages other foreign matter.
Watch Operation Guide 3552 General Guide Indicators Before Getting Started... ① ① ② ③ ④ ⑤ This section provides an overview of the watch and introduces convenient ways it can be ⑨ used. ⑩ ⑪ Watch Features ⑫ ⑥ Phone Linking ●...
In any mode, hold down (C) for at least one cycles the display information as shown ● the battery. second to return to the Timekeeping Mode. below. Request battery replacement from a CASIO Normal Timekeeping Step count display service center or your original retailer. Display Timekeeping Mode If [R] is flashing on the display ●...
Watch Operation Guide 3552 To illuminate the face when Auto Light ● Power Saving Note is enabled If power saving is enabled, the watch will turn If Auto Light is enabled, face illumination will Under the conditions below, the ●...
To transfer data to a watch and to configure settings, you first need to pair the watch with your phone. Getting Ready Press (A) to exit the setting screen. Your phone needs to have the “CASIO ● WATCHES” phone app installed to pair with the watch.
Note While the CASIO WATCHES phone Note ー app is not running on the phone The first time you start up the CASIO For details about setting procedures, ● ● WATCHES phone app, a message will see your phone documentation.
You can configure settings so the watch You can use the CASIO WATCHES phone Whenever you want to trigger immediate time receives CASIO WATCHES update and other app to enable or disable power saving.
This section explains how to send lap times app to view the data below, which is measured and split times (up to 200 records) stored in Specifying a World Time City with the CASIO by the watch. watch memory, and other data to your phone WATCHES phone app causes the watch’s...
Page 13
Watch Operation Guide 3552 To select a World Time City Swapping Your World Time and Home ● ● 3. Y Perform the operation shown on the Time 1. Y Tap the “CASIO WATCHES” icon. phone screen to select a summer time 1.
You can use phone finder to trigger a tone on Alarm time, timer start time, and other settings the phone to make it easy to find. The tone is can also be configured using the CASIO 1. Y Tap the “CASIO WATCHES” icon.
If the watch is not paired with the phone you on your phone. Recorded location information ● want to connect with, refer to the information can be viewed on the CASIO WATCHES below and pair them. phone app map while the watch is connected with your phone.
Watch Operation Guide 3552 Deleting Pairing Information from the ● Using Watch Operations to Time Adjustment Watch Adjust the Time Setting 1. X Hold down (C) for at least one second Your watch can connect with a phone to obtain If your watch cannot connect with your phone to enter the Timekeeping Mode.
Settings display. minutes of non-operation. If the watch is paired with a phone, you can also use the CASIO WATCHES phone app to set the World Time city. Configuring World Time Settings Note Press (D) to toggle the setting between World Time cities that can be selected ●...
Use (B) and (D) to set the minute setting. Navigating Between Modes If the watch is paired with a phone, you can also use the CASIO WATCHES phone app to Press (A) to exit the setting screen. Hold down (D) for at least two seconds.
Watch Operation Guide 3552 Enabling the Hourly Time Moving to Another Enter the Alarm Mode. Signal Time Zone Navigating Between Modes Use (D) to scroll through the alarm ([AL1] Enter the Alarm Mode. to [AL5]) and hourly time signal ([SIG])
● units for the first hour of the Viewing Saved Data measurement. After the first hour, You can use the CASIO WATCHES ● elapsed time is shown in one-second phone app to view past measurement units.
Watch Operation Guide 3552 Measuring a Split Time or Lap Viewing the Current Time Press (A) to cycle through measurement Time While in the Stopwatch Mode numbers. Each time you press (A), the next older ● Pressing (A) while the stopwatch is reset to all Enter the Stopwatch Mode.
Configure Timer Settings This deletes the displayed data. has been deleted. If the watch is paired with a phone, you can also use the CASIO WATCHES phone app to set the timer start time. Configuring Watch Settings Setting the Countdown Start...
Watch Operation Guide 3552 Counting Steps Pedometer Press (C). This causes the seconds digits to flash. If you are wearing the watch correctly, the watch will count your steps as you walk or You can use your watch to keep track of your Seconds engage in your normal daily activities.
Watch Operation Guide 3552 Interpreting the Step Count Graph Checking Your Progress to Your Daily ● ● Resetting Today’s Step Step Target The Step Count Graph shows the number of Count steps (up to 1,000) you have taken each hour.
Watch Operation Guide 3552 Step Reminder Enabling/Disabling Step Other Settings Reminder If the watch determines that you have not walked for a preset amount of time, it will This section explains other watch settings you Enter the Timekeeping Mode. sound a tone and display a flashing Step can configure.
([ON] or [OFF]) to flash on the Alarm ● display. For information about phones that can Enter the Timekeeping Mode. connect with the watch, visit the CASIO Navigating Between Modes website. https://world.casio.com/os_mobile/wat/ Hold down (A) for at least two seconds. This causes the current step reminder...
Bluetooth SIG, Inc. and any use of such World Time Are your phone’s Bluetooth settings marks by CASIO Computer Co., Ltd. is Current time for approximately 300 cities configured correctly? under license. selected for the watch iPhone and App Store are trademarks of Configure the phone’s Bluetooth settings.
Page 28
Has the watch been re-paired with the On your phone, re-enable Bluetooth, and then phone? go to the Home Screen and tap the “CASIO WATCHES” icon. Next, on the watch, hold After deleting pairing information from the down (C) for at least three seconds.
Page 29
Auto time adjustment will not be it could indicate a faulty sensor. performed at the scheduled times unless Contact a CASIO service center or your it is enabled. Enable auto time original retailer. adjustment.
Page 30
Battery is flashing on the display. This indicates that battery power is getting low. Request battery replacement from a CASIO service center or your original retailer. Battery Replacement [R] is flashing on the display. [R] may appear on the display when the watch’s battery power is low, or if you use the...