Technics SL-C700 - Compact Disc Player Manual

Features of this unit

This unit offers the following features:

High Res Re-master
The High Res Re-master function enables high-precision expansion of bandwidth and bit depth for high-quality sound reproduction from music CDs and other compressed sources.

High Precision Master Clock
A high-precision master clock, generated by very precise crystals, drives all the digital circuits, ensuring accurate reproduction.

High Quality Analog Circuit
Equipped with an L/R independent high-precision parallel DAC that eliminates channel interference and reproduces a rich sound field.

Recommended devices

We recommend using Technics devices (optional) for superior audio quality.

Product name	Model number
Speaker System	SB-C700
Network Audio Player	ST-C700
Stereo Integrated Amplifier	SU-C700

Accessories

*The illustrations shown may differ from your unit.

(ONLY FOR CANADA)
The enclosed Canadian French label sheet corresponds to the English display on the unit.

• Product numbers provided in this Owner's Manual are correct as of March 2015. These may be subject to change.
• Do not use AC power supply cord with other equipment.

Unit care

Pull out the AC power supply cord from the outlet before maintenance. Clean this unit with a soft cloth.

• When dirt is heavy, wring a wet cloth tightly to wipe the dirt, and then wipe it with a soft cloth.
• Do not use solvents including benzine, thinner, alcohol, kitchen detergent, a chemical wiper, etc. This might cause the exterior case to be deformed or the coating to come off.

Control reference guide

This unit

Front

1. Power switch lever
   Turn on/off this unit.
   • The remote control does not operate when the power switch lever is in the lowered position.
2. Remote control signal sensor
   Distance: Within approx. 7 m (23 ft) directly in front
   Angle: Approx. 30o left and right
   • A remote control is not supplied with this unit. Use the remote control supplied with the SU-C700/ST-C700 to control this unit.
3. Display
4. Basic control switches
   These switches work just by touching the marks. Each time you touch the switch, there will be a beep sound.
5. Disc tray

Rear

6. System terminal [CONTROL]
7. Analog audio output terminal [LINE OUT]
8. Product identification marking
   The model number is indicated.
9. Digital audio output terminal [OPT OUT]
10. Digital audio output terminal [COAX OUT]
11. AC IN terminal [AC IN ~]

Remote control (supplied with the SU-C700/ST-C700)

Use the remote control supplied with the SU-C700/ST-C700 to control this unit.
For information on the operations of the SU-C700/ST-C700, please also refer to their operating instructions.

1. [CD ]: Standby/on switch
   Press to switch the unit from on to standby mode or vice versa. In standby mode, the unit is still consuming a small amount of power.
   • The remote control does not operate when the power switch lever is in the lowered position.
2. [AMP]/[NWP]/[CD]: Select the device to be operated
3. [DIMMER]: Adjust the brightness of the display, etc.
4. [INFO]: View content information
5. / [OK]: Selection/OK
6. [RETURN]: Return to the previous display
7. [MENU]: Enter menu
8. [RE-MASTER]: Turn on/off Re-master
9. Basic playback control buttons
10. Numeric buttons, etc.
    • To select a 2-digit number
      Example: 16: [≧10] → [1] → [6]
      • To select a 3-digit number
        Example: 124: [S10] → [≧10] → [1] → [2] → [4]
      • [CLEAR]: Clear the entered value.

Getting started

• Turn off all equipment before connection and read the appropriate operating instructions.
• Do not connect the AC power supply cord until all other connections are complete.
• Fully insert the cable plug into the pin jack to assure a good connection.
• Do not bend cables at sharp angles.

System control connection to an SU-C700

• You can automatically link this unit with the SU-C700 and operate them easily with the remote control.
• You can output digital audio signals from this unit and play back music.

• Do not use any other system connection cables or coaxial digital cables except the supplied one.
• Connect the system connection cable to the system terminal [CONTROL2] of the SU-C700.
• Connect the coaxial digital cable to the digital audio input terminal [COAX2 IN] of the SU-C700.

Connecting to an amplifier and a D/A converter

You can output analog or digital audio signals from this unit and play back music.

This unit (rear)

AC power supply cord connection

Connect only after all other connections are completed.

• This unit consumes a small amount of AC power (> 19) even the power switch lever is in the [OFF] position. Remove the plug from the main electrical outlet if you will not be using the unit for an extended period of time. Place the unit so the plug can be easily removed.

Playing back CDs

Refer to "Notes on CDs" for information about the discs this unit can play back.

Preparation

• Turn on the connected device (amplifier, etc.) and lower its volume.

1. Raise the power switch lever of this unit to the [] position.
2. Touch [] on the unit to open the disc tray and insert a CD.
   Place label up in the proper position in the middle of the disc tray.
   
   Touch [] again to close the disc tray.
3. Touch [ ].
   Adjust the volume of the connected device. (amplifier, etc.)

Operations during playback

Stop	Touch []. When using the SU-C700/ST-C700 remote control, press [CD] first, and then press [].
Pause	Touch []. Touch again to restart play. When using the SU-C700/ST-C700 remote control, press [CD] first, and then press [].
Skip	Touch [] or [] to skip track. When using the SU-C700/ST-C700 remote control, press [CD] first, and then press [] or [ ].
Search	During play or pause, touch and hold [] or [ ]. When using the SU-C700/ST-C700 remote control, press [CD] first, and then press and hold either [] or [].

Random repeat playback

1. Touch [MENU] repeatedly to select "Random".
2. Touch [] to select an item and then touch [ ].

On	All tracks are repeated randomly. "RND " is displayed.
Off	Turns off random repeat mode.

• When using the SU-C700/ST-C700 remote control, press [CD] first, and then press [RND]. (Press again to turn off random repeat mode.)
• Random repeat mode also turns off:
  • When the disc tray is opened.
  • When the unit is turned to standby or off mode.
  • When the auto off function works.

Repeat playback

1. Touch [MENU] repeatedly to select "Repeat".
2. Touch [] to select an item and then touch [].

1 Track	Only plays the selected track. "1 " is displayed.
All Tracks	All tracks are repeated. " " is displayed.
Off	Turns off repeat mode.

• When using the SU-C700/ST-C700 remote control, press [CD] first, and then press []. (Press again to turn off repeat mode.)
• Repeat mode also turns off:
  • When the disc tray is opened.
  • When the unit is turned to standby or off mode.
  • When the auto off function works.

Viewing information such as the remaining playback time

• Only available from the SU-C700/ST-C700 remote control:

1. Press [CD].
2. Press [INFO] while playing back or paused.
   The information displayed changes each time you press the button.

For CD-DA:
The display changes as follows; elapsed play time of the track, remaining time for the track, and remaining time on the entire disc (or entire program).

For MP3/WMA:
The display changes as follows; file name, folder name, title name, artist name, album name, format, etc.

Program playback

This function allows you to program up to 25 tracks.

• Only available from the SU-C700/ST-C700 remote control:

1. Press [PGM] in the stop mode.
   • "PGM" screen will be displayed.
2. Select tracks
   For CD-DA:
   Press the numeric buttons
   For MP3/WMA:
   Select folders/files
   • Repeat this step to make further selections.
3. Press [ ] to start playback.

Operations on the remote control

Stop	Press []. Programmed content is maintained.
Check the programmed order	Press [] or [] in the stop mode.
Add tracks	Do steps 2 through 3 in the stop mode.
Clear the last track	Press [CLEAR] in the stop mode. It is not possible to select and clear the desired programmed track.
Cancel program mode	Press [PGM] in the stop mode. "PGM" disappears. (Programmed content is maintained)

• The program memory will be cleared:
  • When the disc tray is opened.
  • When the unit is turned to standby or off mode.
  • When the auto off function works.
• Program play settings are not possible while playing back a CD.
• Random repeat playback is not possible during program playback.
• You can also cancel program mode by operating the touch panel on this unit.

1. Touch [MENU] repeatedly to select "Play Mode".
2. Touch [] to select the item and then touch [ ].

Selecting folders and files for MP3/WMA CDs

For MP3/WMA CDs, files (MP3/WMA files) may be organized in a hierarchy, with folders containing files and subfolders, as shown below.

If you don't select a specific MP3/WMA file or folder for playback, all of the MP3/WMA files on the CD will be played in numerical order starting with file #1.

Selecting files in folder mode

In folder mode, all folders containing files are shown as the same level, so you can select files without worrying about the structure of the folders. Select while the disc is stopped.

Operation with the touch panel on the unit:

1. Touch [MENU] repeatedly to select "Folder" and then touch [].
   • The first folder is displayed. ("Root" is displayed if it is the root folder.)
2. Touch [].
   • Another folder name is displayed.
3. Touch [] so that you can select the files in that folder.
   • Touch [ ] to display the files in the folder.
   • Touch [] to enable selection of a different folder and select different files.
4. Touch [].
   • Playback starts for the displayed folder or file.
   • Touch [ ] to stop playback.

Operation with the SU-C700/ST-C700 remote control:

1. Press [CD].
2. Press [MENU].
3. Press [] repeatedly to select "Folder" and then press [OK].
   • The first folder is displayed. ("Root" is displayed if it is the root folder.)
4. Press [] or [ ].
   • Another folder name is displayed.
5. Press [ ] or [OK] so that you can select the files in that folder.
6. The first file name in the folder is displayed.
   • Press [ ] or [] to display the files in the folder.
   • Press [ ] or [RETURN] to enable selection of a different folder and select different files.
7. Press [ ] or [OK].
   • Playback starts for the displayed folder or file.
   • To cancel the procedure at any point, press the [].

Selecting the playback mode

All: Plays back all tracks on the CD.
1 Folder: Plays back the tracks in a folder.

Operation with the touch panel on the unit:

1. Touch [MENU] repeatedly to select "Play Mode".
2. Touch [ ] to select the item and then touch [ ].

Operation with the SU-C700/ST-C700 remote control:

1. Press [CD].
2. Press [MENU].
3. Press [] repeatedly to select "Play Mode".
4. Press [ ] to select the item and then press [OK].

Others

Display brightness

The brightness of this unit's display and the basic control switches can be changed.

Operation with the touch panel on the unit:

1. Touch [MENU] repeatedly to select "Dimmer".
2. Touch [ ] to select an item and then touch [ ].

• When using the SU-C700/ST-C700 remote control, press [DIMMER] to select the brightness.
• When the display is turned off, it will light up only when you operate this unit.
  Before the display turns off again, "Display Off" will be displayed for a few seconds.

Operation sound setting

You can turn the beep sound on/off.

• The factory default is "On".

Operation with the touch panel on the unit:

1. Touch [MENU] repeatedly to select "Setup" and then touch [].
2. Touch [MENU] repeatedly to select "Beep".
3. Touch [] to select an item and then touch [].
4. Touch [] twice after you have finished setting.

Operation with the SU-C700/ST-C700 remote control:

1. Press [CD].
2. Press [MENU].
3. Press [] repeatedly to select "Setup" and then press [OK].
4. Press [ ] repeatedly to select "Beep".
5. Press [ ] to select "On"/"Off" and then press [OK].
6. Press [MENU] after you have finished setting.

Auto off function

This unit is designed to conserve its power consumption and save energy. The unit will turn to standby mode automatically if there is no sound and it is not being used for approximately 20 minutes.

• The factory default is "On".

To cancel this function

Operation with the touch panel on the unit:

1. Touch [MENU] repeatedly to select "Setup" and then touch [].
2. Touch [MENU] repeatedly to select "AUTO OFF".
3. Touch [] to select an item and then touch [].
4. Touch [] twice after you have finished setting.

Operation with the SU-C700/ST-C700 remote control:

1. Press [CD].
2. Press [MENU].
3. Press [] repeatedly to select "Setup" and then press [OK].
4. Press [] repeatedly to select "AUTO OFF".
5. Press [ ] to select "Off" and then press [OK].
   • To enable the output again, select "On".
6. Press [MENU] after you have finished setting.

The auto off function works unless you turn it off, even if you turn off and on this unit.

CD EXTRA

Make settings to play back CD EXTRA discs.
Audio: Plays back CD-DA data.
MP3/WMA: Plays back MP3/WMA data.

• The factory default is "Audio".

Operation with the touch panel on the unit:

1. Touch [MENU] repeatedly to select "Setup" and then touch [].
2. Touch [MENU] repeatedly to select "CD EXTRA".
3. Touch [] to select an item and then touch [].

Operation with the SU-C700/ST-C700 remote control:

1. Press [CD].
2. Press [MENU].
3. Press [] repeatedly to select "Setup" and then press [OK].
4. Press [] repeatedly to select "CD EXTRA".
5. Press [] to select an item and then press [OK].

Listening to more naturalsounding audio (Re-master)

Re-mastering expands the playback band and achieves a higher bit depth to reproduce natural and expansive sound close to original music.

• The factory default is "Off".

Operation with the touch panel on the unit:

1. Touch [MENU] repeatedly to select "RE-MASTER".
2. Touch [ ] to select an item and then touch [ ].

Operation with the SU-C700/ST-C700 remote control:

1. Press [CD].
2. Press [RE-MASTER] to select "On"/"Off".

This function works for both the analog and digital audio outputs.

Setting the upper limit for the sampling frequency during digital output

You can set the upper limit for the sampling frequency for signals output from the digital audio output terminal when [RE-MASTER] is "On". The sampling frequencies you can transmit depend on the device you have connected. Refer to the operating instructions for the device you have connected for details.

• The factory default is "176.4kHz".
• We recommend that you select "176.4kHz" when you have connected this unit and SU-C700 as a system.

Operation with the touch panel on the unit:

1. Touch [MENU] repeatedly to select "Setup" and then touch [].
2. Touch [MENU] repeatedly to select "Digital Output".
3. Touch [] to select an item and then touch [].
4. Touch [] twice after you have finished setting.

Operation with the SU-C700/ST-C700 remote control:

1. Press [CD].
2. Press [MENU].
3. Press [] repeatedly to select "Setup" and then press [OK].
4. Press [] repeatedly to select "Digital Output".
5. Press [] to select an item and then press [OK].
   • You can select a sampling frequency of 44.1 kHz or 176.4 kHz.
6. Press [MENU] after you have finished setting.

• Depending on the music source that you play back, the applied setting may be less effective.
• Depending on the music source that you play back, it may not be possible to achieve the desired audio quality and sound field effect. In such cases, turn off this function.
• It may take some time to output audio when you have adjusted the audio quality.
• This has no effect on analog audio output.
• Sound may not be output when you set to 176.4 kHz, depending on the device you have connected. Set to 44.1 kHz if this occurs. ([RE-MASTER] will be disabled.)

Remote control code

When other equipment responds to the supplied remote control, change the remote control code.

• The factory default is "Mode 1".
  
• Only available from the SU-C700/ST-C700 remote control: Point the remote control at this unit, and press and hold [OK] and the numeric button for at least 4 seconds.
• When the remote control code is changed, the new code will appear on the display for a few seconds.

[OK] + [1]	Set the code to "Mode 1"
[OK] + [2]	Set the code to "Mode 2"

When the SU-C700/ST-C700 is connected via the system control function, change its remote control code as well as the remote control code for this unit.

Language

Select English or French for the display.

• The factory default is "English".

Operation with the touch panel on the unit:

1. Touch [MENU] repeatedly to select "Setup" and then touch [].
2. Touch [MENU] repeatedly to select "Language".
3. Touch [] to select "English"/ "Français" and then touch [].
4. Touch [] twice after you have finished setting.

Operation with the SU-C700/ST-C700 remote control:

1. Press [CD].
2. Press [MENU].
3. Press [] repeatedly to select "Setup" and then press [OK].
4. Press [] repeatedly to select "Language".
5. Press [] to select "English"/"Français" and then press [OK].
6. Press [MENU] after you have finished setting.

Using the system control function

You can automatically link this unit with SU-C700 to operate them.

Preparation

1. Connect this unit and the SU-C700 with a system connection cable and a coaxial digital cable.
2. Set the power switch lever of this unit and the SU-C700 to the [ ] position.

Switching this unit and the SU-C700 to on/standby simultaneously

• When this unit and SU-C700 are in standby mode, while pointing the SU-C700/ST-C700 remote control at this unit, press [CD ] so that this unit and SU-C700 switch on automatically.

Switching the SU-C700's input source automatically

When you perform an operation such as playback on this unit, the input source of the SU-C700 will be automatically switched to "COAX2".

For information on the operations of the SU-C700, please also refer to its operating instructions.

Notes on CDs

Compatible CD

• A disc with the CD Logo.
  
• This unit can play back discs that conform to the CD-DA format.
• The unit may not be able to play some discs due to the condition of the recording.
• Before playback, finalize the disc on the device it was recorded on.

Compatible MP3 files

• Supported format: Files with the extension ".mp3" or ".MP3".
• Compatible compression rate: Between 16 kbps and 320 kbps (stereo).
• Sampling Rate: 32, 44.1, 48 kHz.
• Depending on how you create the MP3 files, they may not play in the order you numbered them or may not play at all.

Compatible WMA files

• Supported format: Files with the extension ".wma" or ".WMA".
• Compatible compression rate: Between 32 kbps and 192 kbps (stereo).
• Depending on how you create the WMA files, they may not play in the order you numbered them or may not play at all.

CD-R/RW

• Maximum number of tracks and albums: 499 tracks and 99 albums (Including Root folder).
• Disc formats: ISO9660 level 1 and level 2 (except for extended formats).
• This unit cannot play files recorded using packet write.

Note about using a DualDisc

• The digital audio content side of a DualDisc does not meet the technical specifications of the Compact Disc Digital Audio (CDDA) format so play may not be possible.
• Do not use a DualDisc in this unit as it may not be possible to insert it correctly and it may get scratched.

This unit can display the "Windows-1252" character code.

Troubleshooting

Before requesting service, make the following checks. If you are uncertain about some of the check points, or if the solutions indicated in the following guide does not resolve the issue, then consult your dealer for instructions.

Heat buildup of this unit.

• This unit becomes warm when used for a long time. This is not a malfunction.

To return all settings to the factory defaults

When the following situations occur, reset the memory:

• There is no response when buttons are pressed.
• You want to clear and reset the memory contents.

Operation with the touch panel on the unit:

1. Touch [MENU] repeatedly to select "Setup" and then touch [].
2. Touch [MENU] repeatedly to select "Initialization".
3. Touch [] to select "Yes" and then touch [].
4. Touch [] to select "Yes" and then touch [] again.

Operation with the SU-C700/ST-C700 remote control:

1. Press [CD].
2. Press [MENU].
3. Press [] repeatedly to select "Setup" and then press [OK].
4. Press [] repeatedly to select "Initialization" and then press [OK].
5. Press [] to select "Yes" and then press [OK].
6. Press [] to select "Yes" and then press [OK] again.

General

A "humming" sound can be heard during playback

• An AC power supply cord or fluorescent light is near the cables. Keep other appliances and cords away from the cables of this unit.

No sound

• Check the volume of the connected device (amplifier, etc.).
• Check to see if the cable connections to the input and output terminals are incorrect. If this is the case, turn off this unit and reconnect the cables correctly.
• Fully insert the cable plug into the pin jack to assure a good connection.

The sound is interrupted

• Depending on your environment, the audio may be interrupted during playback. Check the operating instructions of the connected device and the connection to the device.

Playback does not start

• Depending on your environment or connected devices, it may take some time.

The system control function is not working

• Connect the system connection cable to the system terminal [CONTROL2] of the SU-C700.
• Connect the coaxial digital cable to the digital audio input terminal [COAX2 IN] of the SU-C700.

The unit enters standby mode automatically

• Is the auto off function turned on?
• If the SU-C700 is connected to this unit via the system control function, this unit may automatically enter standby mode when the SU-C700 enters standby mode.

Disc

Incorrect display or play does not start

• Make sure that the disc is compatible with this unit.
• There is moisture on the lens. Wait for about an hour and then try again.
• Unfinalised CD-R and CD-RW cannot be played back.

Playback takes time to start

• It may take some time for the disc to load if there are a lot of tracks or folders on it.

Remote control

(Supplied with the SU-C700/ST-C700)

The remote control does not work properly

• To avoid interference, please do not put any objects in front of signal sensor.
• Change the remote control code if other products react to this remote control.
• If the SU-C700/ST-C700 is selected for the device to be operated, press [CD] and retry the operation.
• When this unit and the SU-C700 are connected with an audio cable, switch the input of the SU-C700 to "LINE".

Pressing [DIMMER] changes the display,

the light and the indicator brightness of the SU-C700/STC700

• [DIMMER] works for the SU-C700/ST-C700 as well as this unit. Turn off the device that you want to maintain the brightness level of, and press [DIMMER].

Messages

The following messages or service numbers may appear on the unit's display.

"Full"

• The number of programmed tracks is more than 25.

"Not Conditional"

• The function you have tried to use is not available with the current settings. Check the steps and settings.

"No Disc"

• Insert the disc to be played.

"No File"

• Insert the disc to be played.
• Insert a disc that has MP3/WMA files on it.

"No Play"

• A CD that is not in CD-DA, MP3 or WMA format is inserted. It cannot be played.
• Examine the content. You can only play supported format.

"Reading"

• The unit is checking the CD information. After this display has disappeared, start operating.

"Remote " ("  " stands for a number.)

• The remote control and this unit are using different codes. Change the code on the remote control.
  • When "Remote 1" is displayed, press and hold [OK] and [1] for at least 4 seconds.
  • When "Remote 2" is displayed, press and hold [OK] and [2] for at least 4 seconds.

-- --:-- --

• The display time is over 99 minutes and 59 seconds.

Specifications

GENERAL

Power supply	AC 120 V, 60 Hz
Power consumption	10 W
Power consumption in standby mode	Approx. 0.5 W
Power consumption in off mode	Approx. 0.5 W
Dimensions (WkHkD)	340 mm x 78 mm x 295 mm (13 3/8 x 3 1/16 x 11 5/8")
Mass (Weight)	Approx. 5.2 kg (11.44 lbs)
Operating temperature range	0 oC to +40 oC (+32 oF to +104 oF)
Operating humidity range	35% to 80% RH (no condensation)

TERMINALS SECTION

Analog output
LINE OUT	Pin jack
Digital output
Optical digital output	Optical terminal
Coaxial digital output	Pin jack
System port
System control	3.5 mm ( 1/8") jack

DISC SECTION

Playable Disc (8 cm or 12 cm)	CD, CD-R/RW (CD-DA, MP3* 1 , WMA* 1 )
MP3	MPEG-1 Audio Layer 3* 2
WMA	Windows Media Audio9* 3
Pick up
Wavelength	790 nm
Laser power	CLASS 1
Channel	2 ch (Stereo)

ANALOG OUTPUT SECTION

Channel	2 ch
Output level
LINE OUT	2.0 Vrms
Frequency response	2 Hz to 20 kHz (-0.5 dB)
THD+N	0.0018% (1 kHz, 0 dB)
S/N	117 dB (IHF-A)
Dynamic range	100 dB (IHF-A)

• Specifications are subject to change without notice.
• Mass and dimensions are approximate.

*¹ ISO9660 Level-1, Level-2, Joliet, Romeo
Recommended single-session. Recommended finalized disc.

*² ID3 tag: ver.2(2.2/2.3) and ver.1(1.0/1.1) supported

*³ Not support WMA9 Pro/WMA9 Lossless/WMA9 Voice. Not support file with DRM.

IMPORTANT SAFETY INSTRUCTIONS

Read these operating instructions carefully before using the unit. Follow the safety instructions on the unit and the applicable safety instructions listed below. Keep these operating instructions handy for future reference.

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
    
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
    Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Unit

• To reduce the risk of fire, electric shock or product damage,
  • Do not expose this unit to rain, moisture, dripping or splashing.
  • Do not place objects filled with liquids, such as vases, on this unit.
  • Use only the recommended accessories.
  • Do not remove covers.
  • Do not repair this unit by yourself. Refer servicing to qualified service personnel.
  • Do not let metal objects fall inside this unit.
  • Do not place heavy items on this unit.

AC power supply cord

• The power plug is the disconnecting device.
  Install this unit so that the power plug can be unplugged from the socket outlet immediately.

Unit

• This unit utilizes a laser. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
• Do not place sources of naked flames, such as lighted candles, on this unit.
• This unit may receive radio interference caused by mobile telephones during use. If such interference occurs, please increase separation between this unit and the mobile telephone.

Placement

• Place this unit on an even surface.
• To reduce the risk of fire, electric shock or product damage,
  • Do not install or place this unit in a bookcase, built-in cabinet or in another confined space. Ensure this unit is well ventilated.
  • Do not obstruct this unit's ventilation openings with newspapers, tablecloths, curtains, and similar items.
  • Do not expose this unit to direct sunlight, high temperatures, high humidity, and excessive vibration.
• Keep your speakers at least 10 mm (¹³/₃₂ ") away from the system for proper ventilation.
• Do not lift or carry this unit by holding any of its levers. Doing so may cause this unit to fall, resulting in personal injury or malfunction of this unit.

RISK OF ELECTRIC SHOCK
DO NOT OPEN

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE SCREWS.
NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

If you have any questions, visit:
U.S.A.: www.panasonic.com/support
Canada: www.panasonic.ca/english/support
Register online at www.panasonic.com/register
(U.S. customers only)

Documents / Resources

References

• Panasonic - Official Consumer Product Support
• Panasonic - Official Consumer Product Support
• Product Registration

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Technics SL-C700 - Compact Disc Player Manual