Panasonic SC-AK520 Operating Instructions Manual page 13

How discs with MP3 differ from CDs
You can mark one track each on the discs loaded so that you can
start play from them later.
[
1
To mark a track number 1
During play or stop
Select your desired track.
(For MP3, refer to "Track skip play" on page 10.
For CD-DA, press the numbered buttons on the remote control.
To select track 10 or over, press [->10] then the two digits.)
On the remote control
Hold down [MARKER] until "STORING" blinks on the
display.
On the main unit
Hold down [MARKER, -MEMORY] until "STORING"
blinks on the display.
The selected track is stored in the marker of the current disc.
If a track is already stored in the marker, it will be replaced next time
you store a new track in the same marker.
To recall a marked track number in the current disc J
During play or stop
On the remote control
Press [MARKER] to recall a marker.
On the main unit _
Press [MARKER, -RECALL] to recall a marker.
Play starts from the track recalled.
• "NO MARKER" indicates that the marker in the current disc is empty.
• The marker memory is cleared when you open the CD tray.
• For CD-DA, you cannot use this function during 1-RANDOM play
and A-RANDOM play.
• You cannot use this function during program mode.
_£iiiiiiiiiiiiiiiiiiiiiiiiiiii
Radio
Press [TUNER, BAND] to select band.
The unit comes on.
Every time you press the button:
FM _ AM
Press [PLAY MODE] on the remote controlto select
"MANUAL".
Everytimeyoup_ssthebutton:
MANUAL _ PRESET
Hold down [I<I<I/REW/V] or [IIH_I/FF/A] for a moment
to search for a station.
The frequency stops when it finds a clear station.
To stop during the process, press [14141/REW/V] or [I_)_I/FF/A].
Under excessive interference, a station may not be found.
Press [14141/REW/V] or [I_I_/FF/A] repeatedly to tune step-by-
step.
"TUNED" is displayed when a radio station is tuned.
"ST" is displayed when a stereo FM broadcast is being
received.
If noise is excessive in FM
Remote control only
Hold down [PLAY MODE] to display "MONO'.
Monaural sound is selected and noise reduces when reception is
weak.
Hold down [PLAY MODE] again to cancel the mode.
"MONO" is also cancelled if the frequency is changed.
Radio
To receive FM broadcasts allocated in 0.1 MHz steps
Main unit only
Hold down [TUNER, BAND]. The display changes in a few seconds to
show the current minimum FM frequency. Continue to hold down the
button until the minimum frequency changes. The step is changed.
Repeat the above to change the step back.
• After changing the "allocation" setting, the frequencies you previously
preset in the memory will be cleared.
• Sound is momentarily interrupted if you load/unload tapes while
listening to an AM broadcast.
Remote control only
There are two methods of pre-setting stations.
Automatic presetting :All the stations the tuner can receive are
preset.
Manual presetting : You can select the stations to preset and the
order they are preset in.
Up to 15 stations each can be set in the FM and AM bands.
Preparation:
Press [TUNER, BAND] to select "FM" or "AM".
l Automatic presetting ]
Do the following once each for FM and AM.
Preparation: Tune to the frequency where pre-setting is to begin.
Hold down [PROGRAM] until the frequency changes.
The tuner presets all the stations it can receive into the channels in
ascending order. When finished, the last station memorized is tuned in.
AK323
Manual presetting
Pre-set the stations one at a time.
<1) Press [PROGRAM] then press [t,9t,<1, REW/V] or
[1_1_1,A/FF] to tune to the desired station.
(P-] Press [PROGRAM] then press [1<t<1, REW/V] or
I_1_1, A/FFJ to select a channel.
.<3) Press [PROGRAM].
The station occupying a channel is erased if another station is preset
in that channel.
l Selecting channels
Press the numbered buttons to select the channel.
To enter channel 10 or over, press [_->10], then the two digits.
OR
,,<1_ Press [PLAY MODE] to select "PRESET".
_2"_Press [1_1<1,REW/V] or [IIH_I, A/FF] to select the
channel.
RQT7330