Table of Contents
Advertisement
KBefore using for the first
time
B efore you can use your new appliance, you must
B e f o r e u s i n g f o r t h e f i r s t t i m e
make some settings. You must also clean the cooking
compartment and accessories.
Before using for the first time
Before using the appliance for the first time, ask your
water supplier about the hardness of your tap water.
To ensure that the appliance can reliably remind you to
descale it when required, you must set your water
hardness range correctly.
Caution!
The appliance may become damaged due to the
■
use of unsuitable liquids.
Do not use distilled water, highly chlorinated tap
water (>40 mg/l) or other liquids.
Only use cold, fresh tap water, softened water or
non-carbonated mineral water.
Malfunctions may occur when using filtered or
■
demineralised water.
The appliance may request that you top up the water
tank even though it may be full, or operation with
steam is cancelled after approx. two minutes.
If required, mix filtered or demineralised water with
the bottled non-carbonated mineral water with a ratio
of one to one.
Notes
If your water is very hard, we recommend that you
■
use softened water.
If you only use softened water, you can set the water
■
hardness range to "softened".
If you use mineral water, set the water hardness
■
range to "4 very hard".
If you use mineral water, you must only use non-
■
carbonated mineral water.
Water hardness range
0
1 (up to 1.3 mmol/l)
2 (1.3 - 2.5 mmol/l)
3 (2.5 - 3.8 mmol/l)
4 (above 3.8 mmol/l)
Initial use
After connecting the appliance to the power or following
a power cut, the settings for initial use are shown on the
display. It may take a few seconds for the instruction to
appear.
You can change these settings at any time in the
Note:
basic settings. ~ "Basic settings" on page 27
Setting
00 softened
01 soft
02 medium
03 hard
04 very hard
Before using for the first time
Setting the language
The language is the first setting displayed. "German" is
the preset language.
Turn the rotary selector to set the required language.
1.
Touch the next text field to confirm.
2.
The next setting appears.
Setting the clock
The clock starts at "12:00".
Touch the "Clock" text field.
1.
Set the clock using the rotary selector.
2.
Touch the next text field to confirm.
3.
The next setting appears.
Setting the water hardness
The default water hardness setting is "very hard".
Use the rotary selector to set the water hardness.
1.
Touch the "Complete the settings" text field to
2.
confirm.
A note appears in the display confirming that the initial
use has been completed.
Switch the appliance off using the ÿ On/Off button if
you do not need to use it.
Calibrating the appliance and cleaning the
cooking compartment
The boiling point of water depends on the air pressure.
During calibration, the appliance self-adjusts to the
pressure ratio at the installation location. This will
happen automatically the first time steam-assisted
cooking is used. This produces a lot of steam.
Preparing the appliance for calibration
Remove the accessories from the cooking
1.
compartment.
Remove any leftover packaging, such as polystyrene
2.
pellets, from the cooking compartment.
Before calibrating the appliance, wipe the smooth
3.
surfaces in the cooking compartment with a soft,
damp cloth.
Calibrating the appliance and cleaning the cooking
compartment
Notes
Calibration cannot be started until the cooking
■
compartment is cold (room temperature).
Do not open the appliance door while calibration is
■
in progress, as this will abort the calibration process.
Press the on/off button ÿ to switch on the
1.
appliance.
Fill the water tank. ~ "Filling the water tank"
2.
on page 20
en
15
Advertisement
Table of Contents
