Advertisement
Quick Links
SURE-LITES
Installation Instructions for HR87, HR117, HR12117 Series
IMPORTANT SAFEGUARDS
WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS
BE OBSERVED, INCLUDING THE FOLLOWING:
READ AND FOLLOW ALL SAFETY
INSTRUCTIONS
2,
Do not use outdoors.
3.
Do not let power supply cords touch hot surfaces,
4*
Do not mount near gas or electric heartens,
5^
Equipment should be mounted in locations and at heights where it will
not readily be subjected to tampering by unauthorized personnel.
6.
The use of accessory equipment not recommended by Sure-Lites may
cause an unsafe condition.
7.
Do not use this equipment for other than its intended purpose.
&
The equipment covered by these instructions is approved for remote
fixtures. Check the remote wattage label to determine remote
capability. DO NOT exceed TOTAL OUTPUT RATING of
equipment.
9.
Some units do not require a toad fuse because the solid state transfer
circuit is current limited. Transfer circuit will automatically shut down if
overloaded.
to. Higher current units utilize a transfer relay for remote load and require
fusing. Check fuse replacement label when replacing fuses. DO NOT
exceed rating shown on the fuse replacement label.
11, Caution: Halogen cycle lamp(s) may be used in the equipment To
avoid shattering; Do not operate lamp in excess of rated voltage.
Protect lamp against abrasion and scratches and against liquids when
lamp is operating. Dispose of lamp with care,
12, Halogen cycle lamps operate at high temperatures. Do not store or
place flammable materials near lamp.
is. SAVE THESE INSTRUCTIONS
INSTALLATION
Step f.
Remove coyer and mount urut securely in place.
Step 2
When connecting unit directly to an electrical box, insert bushing supplied with mil 7/8' KQ.
■ S top 3,
Extend unswitened £4 hour supply of rated voltage and connect per diagram. Cap unused ine lead. Connect ground in accordance with NEC orbed codes. Circuit should not ba
energized at this limp-
Step 4.
remote lamps are to be connected, extend DC csrciit per Article 70Q and 720 of the NEC and connect to yellow and violet leads provided.
Step&
Install battery(s) and connect battery RED (+} and SLUE [-} battery leads per wiring diagram. Lamps wil not light at this time.
3 ftp £.
Turn on AC supply and operate test switch. DC lamps will come on. Charge indicator wil stay on. Release test switch. DC lamps will extinguish.
MAINTENANCE:
Replace batteries every 3 to 10 years according to ambient. Equipment should be tested regularly in accordance with local
codes. For multiple battery units, replace all batteries at the same time.
NOTE:
Servicing of any parts should be performed by qualified personnel. For replacement lamps, fuse or PC hoard,
see fixture labels,
OPERATION:
1.
To test, depress test switch. DC lamps will come on.
2.
Release test switch, DC lamps will extinguish.
CAUTION; This series emergency light is furnished with a sophisticated low voltage dropout
circuit to protect battery from over discharge after Its useful output has been used.
Allow 24 hour recharge time after installation or power failure for full load testing,
TROUBLE SHOOTING GUIDE:
EMERGENCY LAMPS DO NOT COME ON- PILOT UGHT OUT BEFORE TEST
1 ^
Check AC Supply - Bn sue unit has 24 hour AC supply
2,
AC Supply on - Blot light out, Replace charge drcuit.
a.
Pilot light on - Lamps do not light. Higher output shorted or battery not connected.
EMERGENCY LAMPS COME ON DIM
1,
Battery dischajgod - Permit unit to charge 24 hours and then retest. It lamps are stiB on dim, check charger for
charge function. If functioning properly replace battery.
2
Remote lamps dim - Check wire size la ranote lamps against wire size chart.
If
the above trouble shooting Ms does hot solve your problem, contact you local Sure-Lites fiqprosen&tive
or the factory for assistance.
COOPER Lighting
SURE-LITES
1121 Highway 74 South, Peachtree City, GA 30269
1/01
Q490QGQ98A
Step 7.
Replace cover
Advertisement
