Table of Contents
Advertisement
5. Press in the spindle lock button while turning disc
nut clockwise. Tighten securely.
6. To remove backing pad and sanding disc,
remove the battery pack and reverse the
procedure.
Installing/Removing/Cleaning
the Dust Screen
Remove battery to avoid starting
1.
WARNING
the tool. To attach the dust
screen, snap the screen over the tool's handle.
2. To remove the dust screen, insert a flat
screwdriver into the notch at the top of the dust
screen and pry away from the tool.
3. To clean the dust screen, tap against a hard
surface, or blow clean with compressed air.
ONE-KEY™
To learn more about the ONE-KEY™ functionality
for this tool, go to:
www.milwaukeetool.com.au/innovation/one-key/.
To download the ONE-KEY™ app, visit the App
Store
or Google Play™ from your smart device.
®
ONE-KEY™ Indicator
Solid Blue
Wireless mode is active and ready
to
ONE-KEY™ app.
Blinking Blue
Tool is actively communicating with
the ONE-KEY™ app.
Blinking Red
Tool is in security lockout and can
be unlocked by the owner via the
ONE-KEY™ app.
OPERATION
To reduce the risk of injury,
WARNING
always
protection
marked
AS/NZS 1337.1.
When working in dusty situations, wear
appropriate respiratory protection or use a
suitable dust extraction solution.
Never grind without proper safety equipment.
Mode Selector Button
MILWAUKEE
Grinders have a speed selection
®
panel located at the end of the handle to set the
minimum and maximum speed. Press the MODE
select button to switch between the different
speeds.
MAXIMUM RPM
MODE 1
MODE 2
3,500
5,000
AUTOSTOP™
AUTOSTOP™ detects quick rotations, such as
those caused by kickback, and shuts off the tool.
To test AUTOSTOP™:
1. Remove accessories and their fasteners (such
as nuts or flanges) from the tool.
2. Stand away from objects and people.
3. Firmly grasp the tool's handles.
4. Hold tool away from the body.
5. Start the tool.
6. Quickly rotate the tool about 90° in any direction.
be
configured
via
wear
proper
to
comply
MODE 3
MODE 4
6,500
7. If AUTOSTOP™ is working, the tool will shut off
and the AUTOSTOP™ light will flash.
8. If AUTOSTOP™ is not working, the tool will
continue to run. Repeat the test. If the tool will not
automatically shut off, return the tool to the
nearest authorised service centre.
WARNING
provided before and during grinding.
To start the tool, grasp and hold the side handle
triggers, then the main handle firmly. Push the
lockoff button forward and squeeze the paddle
switch.
To stop the tool, release the paddle switch or side
handle triggers. Make sure the tool comes to a
complete stop before laying down the tool.
1. After installing new accessories and before
starting work, test the wheel by letting it spin for
one minute before applying it to the workpiece.
WARNING
damaged accessories can mar workpiece,
damage the tool, and cause stress that may
the
cause accessory failure.
2. Use a clamp, vise or other practical means to
hold the workpiece, freeing both hands to control
the tool.
3.
WARNING
NOTE: If the battery is inserted when the tool is
ON, the tool will not run. Turn the tool OFF, then
back ON to begin work.
4. Allow accessory to come to full speed before
beginning work.
eye
5. Control pressure and surface contact between
with
accessory and workpiece.
WARNING
accessory failure or slows speed.
6. When finished, turn off the tool and make sure it
comes to a complete stop before laying it down.
WARNING
protection for the operator if the wheel should break.
When grinding, hold tool at a 5° to 15° angle, using
constant pressure for a uniform finish. Too great an
angle causes concentrated pressure on small areas
which may gouge or burn work surface.
8,500
For best result use only this portion of disc
8
Always hold the tool firmly with
both hands using the handles
Paddle Switch Operation
General Operation
Never use an accessory that has
been dropped. Out-of-balance or
Hold tool securely with both
hands. Start the tool.
Never bang accessory onto work.
Too
much
Using Grinding Wheels
The guard type must match the
wheel type to provide maximum
pressure
causes
Hold at a
5° to 15° angle
Advertisement
Table of Contents
