Assembly And Adjustments; Operation - Black & Decker REVSD4C Instruction Manual

ENGLISH
Charging Procedure (Fig. B)
WARNING: Do not use tool while it is connected to the
USB cable.
1. Insert the micro USB plug
2. Plug the USB plug into any USB port (such as on
8
a computer).
3. Charging is complete in 1 to 3 hours depending on
power supply rating. The charging LED
while charging.
4. Charging is complete when the charging LED
5. The battery can be left charging or the USB cable can
be disconnnected.
Hot/Cold Delay
When the tool detects that the battery is too hot or too cold,
it automatically starts a hot/cold delay, suspending charging
until the battery has reached an appropriate temperature.
The tool then automatically switches to charging mode. This
feature ensures maximum battery life.
1. A cold battery may charge at a slower rate than a
warm battery.
2. Once the battery has reached an appropriate
temperature, the charging procedure will resume.
Electronic Protection System
Li-Ion tools are designed with an Electronic Protection
System that will protect the battery against overloading,
overheating or deep discharge. The tool will automatically
turn off and the battery will need to be recharged.
Important Charging Notes
1. The tool may become warm to the touch while charging.
This is a normal condition, and does not indicate a
problem. To facilitate the cooling of the tool after use,
avoid placing the tool in a warm environment such as in
a metal shed or an uninsulated trailer.
2. If the tool does not charge properly, take the tool and
USB cable to your local service center.
3. You may charge a partially used battery whenever you
desire with no adverse effect on the tool.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, make sure the forward/reverse button is
in the center, locked position while making any
adjustments or removing/installing attachments or
accessories . An accidental start-up can cause injury.
Inserting and Removing Bits (Fig. C)
NOTE: The hex spindle accepts 1/4" (6.4 mm) hex
4
accessories only.
1. To install a bit simply insert it into the cavity in the hex
spindle 4 as shown in Fig. C.
2. To remove the bit, pull it straight out from the hex spindle.

OPERATION

WARNING: To reduce the risk of serious personal
injury, make sure the forward/reverse button is
in the center, locked position while making any
adjustments or removing/installing attachments or
accessories . An accidental start-up can cause injury.
20
into the charging port .
9 6
will illuminate
10
10 turns off.
This screwdriver is intended for tightening and loosening
screws, nuts, and the like and is not equipped with an
impacting mechanism.
Proper Hand Position (Fig. D)
WARNING: To reduce the risk of serious personal
injury, ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main
handle 3 .
LED Worklight (Fig. A)
CAUTION: When using the worklight for purposes
other than screwdriving or drilling be sure to
remove all accessories. Unused accessories could
cause injury or property damage.
CAUTION: Do not stare into the LED. Serious eye
injury could result
NOTE: The LED worklight
5
reverse/lock-off slider 2 is in the center, locked position.
1. When the screwdriver is activated by pressing the On/Off
switch 1 , the LED worklight
2. The LED worklight will turn off after the On/Off switch
has been released.
Switching On and Off (Fig. A, D)
NOTE: When the screwdriver is activated by pressing the On/
Off switch the LED worklight
1
1. To run the screwdriver, press the On/Off switch
2. To stop the screwdriver, release the On/Off switch
3. To lock the tool in the off position, move the forward/
reverse/lock-off slider 2 to the center position.
Forward/Reverse/Lock-off Slider (Fig. E)
For tightening screws, use forward rotation. For loosening
screws, use reverse rotation.
1. To select forward rotation, push the forward/reverse
slider 2 to the right hand position.
2. To select reverse rotation, push the forward/reverse
slider 2 to the left hand position.
3. To lock the tool, set the forward/reverse slider into the
center position.
NOTE: When the forward/reverse/lock-off slider
in the center position the tool is locked-off to prevent
accidental actuation or battery discharge.
Screwdriving
NOTE: For best performance, #8, 2" and smaller fasteners are
recommended, or screw into pre-drilled holes.
1. Grasp the screwdriver as shown in Fig. D.
2. Insert the appropriate screwdriver bit into the hex
spindle 4 .
3. Select forward or reverse rotation using the forward/
reverse/lock-off slider 2 .
4. To run the screwdriver, press the On/Off switch
will still turn ON if the forward/
5 will automatically turn on.
1
will automatically illuminate.
5
1 .
.
1
2 is
.
1