1. Manuals
  2. Brands
  3. Protech Systems Manuals
  4. Desktop
  5. SE-N207
  6. User manual

Protech Systems SE-N207 User Manual

Intel core mobile i7/ i5 / i3 processor compact and fanless embedded pc
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
USER
MANUAL
SE-N207 M2
SE-N207
Intel
Core Mobile i7 / i5
®
/ i3 Processor Compact
and Fanless Embedded
PC

Advertisement

Table of Contents
loading

Related Manuals for Protech Systems SE-N207

Summary of Contents for Protech Systems SE-N207

  • Page 1 USER MANUAL SE-N207 Intel Core Mobile i7 / i5 ® / i3 Processor Compact and Fanless Embedded SE-N207 M2...
  • Page 2 ® Intel Core Mobile i7/ i5/ i3 Processor Compact and Fanless Embedded PC COPYRIGHT NOTICE & TRADEMARK All trademarks and registered trademarks mentioned herein are the property of their respective owners. This manual is copyrighted in July 2020. You may not reproduce or transmit in any form or by any means, electronic, or mechanical, including photocopying and recording.
  • Page 3 FCC NOTICE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

  • Page 4: Table Of Contents

    Contents Revision History ................... viii Introduction ..................1-1 About This Manual ..............1-2 Getting Started ..................2-1 Package List ................2-2 System Overview ............... 2-3 2.2.1 Front View ................2-3 2.2.2 Rear View – PoE LAN ............2-3 2.2.3 Rear View – COM ............... 2-3 2.2.4 Rear View –...
  • Page 5 Component Locations ..............3-3 3.2.1 Top View and Jumper Settings of SB-N207......3-3 3.2.2 Bottom View of SB-N207 ............ 3-5 How to Set Jumpers ..............3-6 Setting Connectors and Jumpers ..........3-8 3.4.1 COM Port (COM1, COM2) ..........3-8 3.4.2 COM1 Pin9 and COM2 PIN9 Definition Selection Guide (JP_COM1, JP_COM2) ............
  • Page 6 3.4.24 PCIE/ mSATA Module Slot (JM1)........3-25 3.4.25 WIFI / BT Module Slot (JM2) ..........3-27 3.4.26 TPM Selection (JP_TPM1) ..........3-29 3.4.27 Flash Descriptor Security Override Selection (J2H1) ..3-29 3.4.28 AT / ATX Mode Selection (JP_AT1) ........3-30 3.4.29 Case Open Selection (JP2) ..........
  • Page 7 List ..................3-44 COM Port Connector (COM3, COM4) ......... 3-45 COM Port Connector (COM5, COM6) ......... 3-45 Slide Switch for COM3, COM4, COM5 and COM6 RS-232/422/485 Mode Selection (SW2, SW3, SW4, SW5) ........3-46 3.5.10 SR-N207-GZZ-5 I/O Add-On Board Top View ....3-47 3.5.11 SR-N207-GZZ-5 I/O Add-On Board Connector ....
  • Page 8 Software Utilities ................. 4-1 Introduction................. 4-2 ® Installing Intel Chipset Software Installation Utility ....4-3 ® Intel Management Engine Components Installer ..... 4-4 Installing RAID Driver Utility ............4-5 Installing Graphics Driver Utility ..........4-6 Installing LAN Driver Utility ............4-7 Installing Sound Driver Utility .............
  • Page 9 Save & Exit ................5-45 Appendix A System Diagram ............A-1 SE-N207 System Exploded Diagram (with rear view 2 x I/O Slot SKU) ..A-3 SE-N207 Rear View (For 4 x COM sku) ...........A-3 SE-N207 Rear View (For 2 x PoE LAN sku) ..........A-3 Appendix B Technical Summary ..........
  • Page 10 Memory Map ...................B-20 Configuring WatchDog Timer ..............B-22 Flash BIOS Update .................B-24...

  • Page 11: Revision History

    Revision History The revision history of SE-N207 User Manual is described below: Version No. Revision History Date • Remove Backplane Connector (JDOCK1) • Revised the descriptions of JP6 and JP_EDP1 jumper. • Added SR-N207-GZZ-1 ~ SR-N207-GZZ-10 Daughter Boards 2020/07/20 connector pin assignment and jumper setting information.

  • Page 12: Introduction

    Introduction This chapter provides the introduction for the SE-N207 system as well as the framework of the user manual. The following topic is included: • About This Manual Page: 1-1 SE-N207 SERIES USER MANUAL...

  • Page 13: About This Manual

    Chapter 1 Introduction 1.1 About This Manual Thank you for purchasing our SE-N207 system. The SE-N207 is an updated system designed to be comparable with the highest performance of IBM AT personal computers. The SE-N207 provides faster processing speed, greater expandability and can handle more tasks than before.

  • Page 14: Getting Started

    Getting Started This chapter provides the information for the SE-N207 system. It describes how to set up the system quickly and outlines the system specifications. The following topics are included: • Package List • System Overview • System Specification • Safety Precautions Experienced users can go to Chapter 3 System Configuration on page 3-1 for a quick start.

  • Page 15: Package List

    Chapter 2 Getting Started 2.1 Package List If you discover any of the items listed below are damaged or lost, please contact your local distributor immediately. Item Q’ty SE-N207 User Manual Driver DVD Page: 2-2 SE-N207 SERIES USER MANUAL...

  • Page 16: System Overview

    LAN2 Line COM2 COM1 POE2 POE1 228.00 2.2.2 Rear View – PoE LAN LAN1 LAN2 ANT1 ANT2 ANT3 ANT4 POE1 POE2 2.2.3 Rear View – COM COM3 COM4 ANT1 ANT3 ANT4 ANT2 COM5 COM6 Page: 2-3 SE-N207 SERIES USER MANUAL...

  • Page 17: Rear View - I/O Expansion

    Chapter 2 Getting Started 2.2.4 Rear View – I/O Expansion ANT3 ANT4 ANT1 ANT2 2.2.5 Top View Page: 2-4 SE-N207 SERIES USER MANUAL...

  • Page 18: Bottom View

    Chapter 2 Getting Started 2.2.6 Bottom View 2.2.7 Left Side View Page: 2-5 SE-N207 SERIES USER MANUAL...

  • Page 19: Right Side View

    Chapter 2 Getting Started 2.2.8 Right Side View 212.09 2.2.9 Quarter View Page: 2-6 SE-N207 SERIES USER MANUAL...

  • Page 20: Accessory

    Chapter 2 Getting Started 2.2.10 Accessory Wall Mount 212.09 Din Rail Page: 2-7 SE-N207 SERIES USER MANUAL...

  • Page 21: Hdd Easy Maintenance

    Optional I/O Expansion Port => Lan Board => COM Board => USB Board => Parallel Port Board => CANBus Board Step 1. Release the screw of I/O board. Step 2. Pull out the I/O board. Page: 2-8 SE-N207 SERIES USER MANUAL...

  • Page 22: Installing Memory And Extension Module

    Memory module Adhesive tape click Step 2. Put the click on to secure. 2.2.14 HDD & Memory Accessories HDD Tray Screw Memory Heatsink M3 x 5 mm Screw x 4 Memory Heatsink x 2 Page: 2-9 SE-N207 SERIES USER MANUAL...

  • Page 23: System Specifications

     2 x COM1/2 for RS232/422/485 (selectable under BIOS) [COM 1/2 for +5v/+12v/RI selectable by jumper]  6 x COM1/2/3/4 for RS232/422/485 (selectable under Serial Ports BIOS) [COM1/2 for +5v/+12v/RI selectable by jumper] (optional) Page: 2-10 SE-N207 SERIES USER MANUAL...
  • Page 24 Parallel Port  2 x DSUB 9-pin connector CANBus Environment Non wide-ranged temp. HDD / SSD  HDD: 0°C ~40°C (32°F ~ 113°F) Operating Temperature  SSD: 0°C ~50°C (32°F ~ 122°F) (with airflow) Page: 2-11 SE-N207 SERIES USER MANUAL...
  • Page 25  -40° ~ 70° C (-40°F ~ 158°F) @humidity 20~95% (with heater, without PoE)  -40°C ~ 85°C (-40°F ~ 185°F) Storage Temperature  Operating Humidity: 20%~ 90% Humidity  Storage Humidity: 20%~ 95% Page: 2-12 SE-N207 SERIES USER MANUAL...

  • Page 26: Safety Precautions

    Avoid direct sunlight exposure for a long period of time. (For example, in a closed car in summer time, avoid the system from any heating device also.) Or do not use SE-N207 when it has been left outdoors in a cold winter day. •...

  • Page 27: System Configuration

    & connector settings, and component locations for the main board. The following topics are included: • Connector & Jumper Quick Reference Table • Main Board Component Locations • How to Set Jumpers • Setting Main Board Connectors and Jumpers Page: 3-1 SE-N207 SERIES USER MANUAL...

  • Page 28: Connector & Jumper Quick Reference Table

    Remote Power Button Connector J_PBTN1 Power Input Connectors PWR_IN1, PWR_IN2 HD Audio Connector AUDIO1 I2C Wafer JI2C1, JI2C2, JI2C3 SD Card Connector SDCARD1 Mainboard Top Side Connectors Mini PCI Express Slot M_PCIE1 PD Connector JPD1 Page: 3-1 SE-N207 SERIES USER MANUAL...
  • Page 29 MCU Update Firmware Connector JMCU1 DC Power Output Connector JVOUT1 Heater Connector JHEAT1 POE Connector JPOE1 RTC Battery Connector JBAT1 Update BIOS Connector JSPI_1 Speaker Connector JSPK1 PCIE/ mSATA Module Slot WIFI / BT Module Slot Page: 3-2 SE-N207 SERIES USER MANUAL...

  • Page 30: Component Locations

    Chapter 3 System Configuration 3.2 Component Locations 3.2.1 Top View and Jumper Settings of SB-N207 Figure 3-1 Main Board Component Location (Top View) Page: 3-3 SE-N207 SERIES USER MANUAL...
  • Page 31 CAUTION: Always touch the main board components by the edges. Never touch components such as a processor by its pins. Take special cares while you are holding electronic circuit boards by the edges only. Do not touch the main board components. Page: 3-4 SE-N207 SERIES USER MANUAL...

  • Page 32: Bottom View Of Sb-N207

    Chapter 3 System Configuration 3.2.2 Bottom View of SB-N207 Figure 3-2 Main Board Component Location (Bottom View) Page: 3-5 SE-N207 SERIES USER MANUAL...

  • Page 33: How To Set Jumpers

    2 to create one setting and shorting. You can also select to connect pins 2 and 3 to create another setting. The format of the jumper picture will be illustrated throughout this manual. The figure below shows different types of jumpers and jumper settings. Page: 3-6 SE-N207 SERIES USER MANUAL...
  • Page 34 Chapter 3 System Configuration Jumper diagrams Jumper settings Page: 3-7 SE-N207 SERIES USER MANUAL...

  • Page 35: Setting Connectors And Jumpers

    COM2 (RS-232/RS422/RS485) Connector Pin Assignment: ASSIGNMENT RS232 RS422 RS485 (Default Setting) COM2_DCD_R RS-485- COM2_RXD_R RS-485+ COM2_TXD_R COM2 COM2_DTR_R COM2_DSR_R COM2_RTS_R COM2_CTS_R COM2_RI_SEL Notes: COM2_RI_SEL. Through the jumper you can choose signal RI/12V/5V on JP_COM2 Page: 3-8 SE-N207 SERIES USER MANUAL...

  • Page 36: Com1 Pin9 And Com2 Pin9 Definition Selection Guide

    COM1 Pin9 and COM2 PIN9 Definition Selection Guide (JP_COM1, JP_COM2) Jumper Location: JP_COM1, JP_COM2 Description: COM1 pin9 (JP_COM1) and COM2 pin9 (JP_COM2) RI/5V/12V Selection SELECTION JUMPER SETTING JUMPER ILLUSTRATION (Default Setting) JP_COM1 JP_COM2 +12V JP_COM1 JP_COM2 JP_COM2 JP_COM1 Page: 3-9 SE-N207 SERIES USER MANUAL...

  • Page 37: Lan1, Lan2 Ports (Lan1, Lan2)

    LAN1_MDI2_DN LAN1_MDI2_DP LAN1_MDI3_DN LAN1_MDI3_DP LAN1_VCT TXCT(N56962126) RXCT(N56962106) SPR1(N56965977) SPR2(N56965974) LAN1_LED_LINK_N_R LAN1_LED_ACT LAN1_LED_100_N_R LAN1 / LAN2 LAN1_LED_1000_N_R SHLD7(NC) LAN1_MDI0_DN LAN1_MDI0_DP LAN1_MDI1_DN LAN1_MDI1_DP LAN1_MDI2_DN LAN1_MDI2_DP LAN1_MDI3_DN LAN1_MDI3_DP LAN1_VCT TXCT(N56966943) RXCT(N56966944) SPR1(N56965890) SPR2(N56965874) LAN2_LED_LINK_N_R LAN2_LED_ACT LAN2_LED_100_N_R LAN2_LED_1000_N_R Page: 3-10 SE-N207 SERIES USER MANUAL...

  • Page 38: Usb 3.1 Connectors (Usb1)

    USB 3.0 signals: ASSIGNMENT ASSIGNMENT USB_12_VCC5 USB3_TX_P1_L USB2_N1_L USB3_TX_N1_L USB2_P1_L USB3_RX_P1_L USB3_RX_N1_L USB_12_VCC5 USB3_TX_P2_L USB2_N2_L USB3_TX_N2_L USB2_P2_L USB3_RX_P2_L USB3_RX_N2_L USB_34_VCC5 USB3_TX_P3_L USB2_N3_L USB3_TX_N3_L USB2_P3_L USB3_RX_P3_L USB3_RX_N3_L USB_34_VCC5 USB3_TX_P4_L USB2_N4_L USB3_TX_N4_L USB1 USB2_P4_L USB3_RX_P4_L USB3_RX_N4_L Page: 3-11 SE-N207 SERIES USER MANUAL...

  • Page 39: Hdmi Port Connector (Hdmi1)

    Chapter 3 System Configuration 3.4.5 HDMI Port Connector (HDMI1) Port Location: HDMI1 Description: Display Port Connector HDMI1 ASSIGNMENT ASSIGNMENT HDMI_D2+ HDMI_D2- HDMI_D1+ HDMI_D1- HDMI_D0+ HDMI_D0- HDMI_D3+ HDMI_D3- RSVD HDMI_CLK HDMI_DATA HDMI_HPD Page: 3-12 SE-N207 SERIES USER MANUAL...

  • Page 40: Hd Audio Connector (Audio1)

    Description: HD Audio Connector for Line In/Line Out/Mic In ASSIGNMENT HD_MIC1-L HD_GND HD_GND MIC1-JD HD_MIC1-R LINE-OUT-L HD_GND Jack_Sense LINE-OUT-R HD_LINE-IN-L_L HD_GND LINE_IN_SEN HD_LINE-IN-R_L AUDIO1 3.4.7 Speaker Connector (JSPK1) Connector Location: JSPK1 Description: Speaker Connector ASSIGNMENT ROUTP ROUTN JSPK1 Page: 3-13 SE-N207 SERIES USER MANUAL...

  • Page 41: Mini Pci Express Slot (M_Pcie1)

    Mini PCI Express is the successor of the Mini PCI card and provides an increased data throughput. The cards have a detached network interface and are equipped with one lane. They are used in particular in embedded designs or compact box PCs. Page: 3-14 SE-N207 SERIES USER MANUAL...
  • Page 42 Connector Location: PWR_IN1 Description: DC Power Input Connector PWR_IN1 ASSIGNMENT ASSIGNMENT WIDE_POWERIN(N55844851) WIDE_POWERIN(N55844851) 3.4.10 Power Input Connector (PWR_IN2) Connector Location: PWR1_IN2 Description: Power Input Connector ASSIGNMENT WIDE_POWERIN(N55844851) PWR1_IN2 Note: PWR_IN1 & PWR_IN2 are co-lay. (Default: PWR_IN2) Page: 3-15 SE-N207 SERIES USER MANUAL...

  • Page 43: Dc Power Output Connector (Jvout1)

    DC Power Output Connector (JVOUT1) Port Location: JVOUT1 Description: 3-pin Power Output Connector ASSIGNMENT V5P0 V12P0 JVOUT1 3.4.12 Remote Power Button Connector (J_PBTN1) Connector Location: J_PBTN1 Description: Remote Power Button Connector ASSIGNMENT PWRBTNJ J_PBTN1 Page: 3-16 SE-N207 SERIES USER MANUAL...

  • Page 44: I2C Wafer (Ji2C2, Ji2C1, Ji2C3)

    Note: I2C1_V. Through the jumper you can choose 12V or 5V on JP_I2C1. JI2C2 Connector Pin Assignment: ASSIGNMENT JI2C2_V GPPC_C17_I2C0_SCL GPPC_C16_I2C0_SDA Note: JI2C2_V. Through the jumper you can choose 12V or 5V on JP_I2C1. JI2C3 Connector Pin Assignment: ASSIGNMENT GPPC_C13_UART1_TXD_UART1 GPPC_C12_UART1_RXD_UART1 Page: 3-17 SE-N207 SERIES USER MANUAL...

  • Page 45: Hdmi / Dp Connector (Display1, Display2)

    Connector Location: DISPLAY1, DISPLAY2 Description: HDMI / DP Connector DISPLAY1 Connector Pin Assignment: ASSIGNMENT DP0_TX0_DP_C_A DP0_TX0_DN_C_A DP0_TX1_DP_C_A DISPLAY1 / DISPLAY2 DP0_TX1_DN_C_A DP0_TX2_DP_C_A DP0_TX2_DN_C_A DP0_TX3_DP_C_A DP0_TX3_DN_C_A G_CEC_A G_NC_A AUXP_SCL_A G_SDA_A AUXN_G_A DPHPD_HDMI5V_A RE_HDMIHPD_A DP_VCC3_A DETECT(N56078490) Page: 3-18 SE-N207 SERIES USER MANUAL...
  • Page 46 Chapter 3 System Configuration DISPLAY2 Connector Pin Assignment: ASSIGNMENT DP0_TX0_DP_C_C DP0_TX0_DN_C_C DP0_TX1_DP_C_C DP0_TX1_DN_C_C DP0_TX2_DP_C_C DP0_TX2_DN_C_C DP0_TX3_DP_C_C DP0_TX3_DN_C_C G_CEC G_NC AUXP_SCL G_SDA AUXN_G DPHPD_HDMI5V_A RE_HDMIHPD DP_VCC3 DETECT(N55402789) Page: 3-19 SE-N207 SERIES USER MANUAL...

  • Page 47: Sd Card Connector (Sdcard1)

    Chapter 3 System Configuration 3.4.15 SD Card Connector (SDCARD1) Connector Location: SDCARD1 Description: SD Card Connector ASSIGNMENT GPPC_G2_SD3_D3_R GPPC_G0_SD3_CMD_R +V3P3S_SD_SW GPPC_G6_SD3_CLK_R GPPC_G1_SD3_D0_R GPPC_G2_SD3_D1_R GPPC_G3_SD3_D2_R SDCARD1 GPPC_G5_SD3_CD_N WP_SW2(N29095979) Page: 3-20 SE-N207 SERIES USER MANUAL...

  • Page 48: Pd Connector (Jpd1)

    SPAER2_A RXCT_A SPAER1_B TXCT_B SPAER2_B RXCT_B V12P0A_L V12P0A_L V12P0A_L JPD1 3.4.17 PSE Connector (JPSE1) Connector Location: JPSE1 Description: PSE Connector ASSIGNMENT ASSIGNMENT V3P3 V3P3A V12P0A_L VOUT_54 V12P0A_L VOUT_54 V12P0A_L OUT2 V12P0A_L JPSE1 OUT1 V12P0A_L Page: 3-21 SE-N207 SERIES USER MANUAL...

  • Page 49: Poe Connector (Jpoe1)

    Connector Location: JPOE1 Description: POE Connector ASSIGNMENT JPOE1 3.4.19 Heater Connector (JHEAT1) Connector Location: JHEAT1 Description: Heater Connector ASSIGNMENT V12P0_HEATER V12P0_HEATER THERMAL_MCU JHEAT1 Note: Heater module function is enabled. Please see JMCU1 jumper setting for details. Page: 3-22 SE-N207 SERIES USER MANUAL...

  • Page 50: Rtc Battery Connector (Jbat1)

    RTC Battery Connector (JBAT1) Connector Location: JBAT1 Description: RTC Battery Connector ASSIGNMENT VBAT JBAT1 3.4.21 Update BIOS Connector (JSPI_1) Connector Location: JSPI_1 Description: Update BIOS Connector ASSIGNMENT ASSIGNMENT V3P3A_SPI SPI_CSJ_0_SW SPI_CLK_SW SPI_MISO_SW SPI_MOSI_SW SPI_HOLDJ0 SPI_WPJ0 JSPI_1 Page: 3-23 SE-N207 SERIES USER MANUAL...

  • Page 51: Lpc / Tpm Connector (Jp1)

    LPC_AD2_D V3P3 LPC_AD1_D Note: Through the jumper you can choose Debug or TPM on JP_TPM1 3.4.23 MCU Update Firmware Connector (JMCU1) Connector Location: JMCU1 Description: MCU Update Firmware Connector ASSIGNMENT MCU_5VSB(N56134297) MCU_SPD MCU_SPC JMCU1 Page: 3-24 SE-N207 SERIES USER MANUAL...

  • Page 52: Pcie/ Msata Module Slot (Jm1)

    Chapter 3 System Configuration SELECTION JUMPER SETTING JUMPER ILLUSTRATION Without Heater (Default Setting) JMCU1 3.4.24 PCIE/ mSATA Module Slot (JM1) Connector Location: JM1 Description: PCIE/ mSATA Module Slot ASSIGNMENT ASSIGNMENT VCC3_3_WLAN VCC3_3_WLAN GPPC_D13_WWAN_FCP_OFF_N WWAN_DISABLE_N Page: 3-25 SE-N207 SERIES USER MANUAL...
  • Page 53 Chapter 3 System Configuration ASSIGNMENT ASSIGNMENT M.2_WWAN_I2S1_BCLK M.2_WWAN_I2S1_OUT M.2_WWAN_I2S1_IN M.2_WWAN_I2S1_LRCLK MINI_PCIE1_TXN MINI_PCIE1_TXP MINI_PCIE1_RXN MINI_PCIE1_RXP M2_PCIE12_SATA1A_RX M2_PCIE12_SATA1A_RX M2_PCIE12_SATA1A_TX M2_PCIE12_SATA1A_TX GPPC_B13_PLTRST_N GPPC_B9_SRCCLKREQ4_N CLK_SRC4_DN CLK_SRC4_DP SUS_CLK GPP_F1_CNV_GNSS_FTA VCC3_3_WLAN VCC3_3_WLAN VCC3_3_WLAN Page: 3-26 SE-N207 SERIES USER MANUAL...

  • Page 54: Wifi / Bt Module Slot (Jm2)

    Description: WIFI / BT Module Slot ASSIGNMENT ASSIGNMENT VCC3_3_WLAN USB2_P10_M.2_BT_R_DP VCC3_3_WLAN USB2_P10_M.2_BT_R_DN M.2_WLAN_LED1_N M.2_BT_PCMCLK CNV_WR_LANE1_R_DN M.2_BT_PCMFRM_CRF_RST_N CNV_WR_LANE1_R_DP M.2_BT_PCMIN M.2_BT_PCMOUT_CLKREQ0 CNV_WR_LANE0_R_DN CNV_WR_LANE0_R_DP GPPC_B2_UART_BT_WAKE_N M.2_CNV_BRI_RSP_BT_UART0 CNV_WR_CLK_R_DN CNV_WR_CLK_R_DP M.2_CNV_RGI_DT_BT_UART0 M.2_CNV_RGI_RSP_BT_UART0 _CTS PCIE_TXDP_M2_E M.2_CNV_BRI_DT_UART0_RTS PCIE_TXDN_M2_E M.2_WLAN_CL_RST_N M.2_WLAN_CL_DATA PCIE_RXDP_M2_E M.2_WLAN_CL_CLK Page: 3-27 SE-N207 SERIES USER MANUAL...
  • Page 55 Chapter 3 System Configuration ASSIGNMENT ASSIGNMENT PCIE_RXDN_M2_E DISC_WLAN_WWAN_COEX3 DISC_WLAN_WWAN_COEX2 CLK_SRC3_M.2_WLAN_DP DISC_WLAN_WWAN_COEX1 CLK_SRC3_M.2_WLAN_DN M.2_BTWIFI_SUS_CLK PE_RST_OUT_82 GPPC_B8_CLKREQ3_WLAN GPPC_B4_BT_RF_KILL_N _R_N M.2_WLAN_PE_WAKE_N GPPC_C2_WIFI_RF_KILL_N CNV_WT_LANE1_DP CNV_WT_LANE1_DN PULSAR_38P4M_REFCLK_MO DULE CNV_WT_LANE0_DP BUF_PLT_RST_N GPPC_B10_CLKREQ5_WIGIG_ CNV_WT_LANE0_DN M.2_WIGIG_PE_WAKE_N CNV_WT_CLK_DN VCC3_3_WLAN CNV_WT_CLK_DP VCC3_3_WLAN Page: 3-28 SE-N207 SERIES USER MANUAL...

  • Page 56: Tpm Selection (Jp_Tpm1)

    (Default Setting) JP_TPM1 TPM Enable JP_TPM1 3.4.27 Flash Descriptor Security Override Selection (J2H1) Jumper Location: J2H1 Description: Flash Descriptor Security Override Selection SELECTION JUMPER SETTING JUMPER ILLUSTRATION Open Normal J2H1 (Default Setting) Disable J2H1 Page: 3-29 SE-N207 SERIES USER MANUAL...

  • Page 57: At / Atx Mode Selection (Jp_At1)

    JUMPER SETTING JUMPER ILLUSTRATION Open ATX Mode (Default Setting) JP_AT1 AT Mode JP_AT1 3.4.29 Case Open Selection (JP2) Jumper Location: JP2 Description: Case Open Selection SELECTION JUMPER SETTING JUMPER ILLUSTRATION Open Normal (Default Setting) Open Page: 3-30 SE-N207 SERIES USER MANUAL...

  • Page 58: Sata / Pcie Mode Selection (Jp3)

    JUMPER SETTING JUMPER ILLUSTRATION Open SATA (Default Setting) PCIE 3.4.31 HDMI/DP Mode Selection (JP6) Jumper Location: JP6 Description: HDMI/DP Hot Plug Detection for HDMI1 SELECTION JUMPER SETTING JUMPER ILLUSTRATION HDMI/DP (Default Setting) Reserved Open Page: 3-31 SE-N207 SERIES USER MANUAL...

  • Page 59: Hdmi / Dp Mode Selection For Display 1 (Jp_Edp1)

    Chapter 3 System Configuration 3.4.32 HDMI / DP Mode Selection for DISPLAY 1 (JP_EDP1) Jumper Location: JP_EDP1 Description: HDMI/DP Selection SELECTION JUMPER SETTING JUMPER ILLUSTRATION HDMI (Default Setting) JP_EDP1 Reserved Page: 3-32 SE-N207 SERIES USER MANUAL...
  • Page 60 I2C Voltage Selection (JP_I2C1) Jumper Location: JP_I2C1 Description: I2C Voltage Selection SELECTION JUMPER SETTING JUMPER ILLUSTRATION JI2C1 launch V3P3 (Default Setting) JP_I2C1 JI2C2 launch V3P3 JP_I2C1 JI2C1 launch V5P0 JP_I2C1 JI2C2 launch V5P0 JP_I2C1 Page: 3-33 SE-N207 SERIES USER MANUAL...

  • Page 61: Clear Cmos Data Selection (Jcmos1)

    Step 4. Power on the PC and the PC will then auto-reboot for once in order to set SoC’s register. Step 5. Done! SELECTION JUMPER SETTING JUMPER ILLUSTRATION Open Normal JCMOS1 (Default Setting) Clear CMOS JCMOS1 Page: 3-34 SE-N207 SERIES USER MANUAL...

  • Page 62: Daughter Board Connectors & Jumpers Quick Reference Table

    I/O Add-On board with 2 x CANBus function SR-N207-GXX-7 PSE board with PoE voltage boost function SR-N207-GXX-8 PD board with PoE voltage buck function SR-N207-GXX-9 I/O Add-On board with 2 x LAN POE function SR-N207-GXX-10 Page: 3-35 SE-N207 SERIES USER MANUAL...

  • Page 63: Sr-N207-Gzz-1 Board Top View

    Chapter 3 System Configuration 3.5.1 SR-N207-GZZ-1 Board Top View 3.5.2 SR-N207-GZZ-1 Board Bottom View 3.5.3 SR-N207-GZZ-1 Backplane Connector & Jumper List Connector Description NAME Digital Input / Output JDIO1 Connector Page: 3-36 SE-N207 SERIES USER MANUAL...
  • Page 64 Digital Input / Output Connector (JDIO1) Connector Location: JDIO1 Description: Digital 8-Input / 8-Output ASSIGNMENT PIN ASSIGNMENT Reserved Reserved DIN_0 DOUT_0 DIN_1 DOUT_1 DIN_2 DOUT_2 DIN_3 DOUT_3 DIN_4 DOUT_4 DIN_5 DOUT_5 DIN_6 DOUT_6 DIN_7 DOUT_7 JDIO1 Page: 3-37 SE-N207 SERIES USER MANUAL...
  • Page 65 Chapter 3 System Configuration DIO Connector ASSIGNMENT DIN0 DIN1 DIN2 DIN3 DIN4 DIN5 DIN6 DIN7 DOUT0 DOUT1 DOUT2 DOUT3 DOUT4 DOUT5 DOUT6 DOUT7 Page: 3-38 SE-N207 SERIES USER MANUAL...

  • Page 66: Sr-N207-Gzz-2 I/O Add-On Board Top View

    3.5.5 SR-N207-GZZ-2 I/O Add-On Board Connectors LAN Ports (LAN1, LAN2) Port Location: LAN1, LAN2 Description: LAN1, LAN2 ports ASSIGNMENT LAN_MDI0_DP LAN_MDI0_DN LAN_MDI1_DP LAN_MDI1_DN LAN_MDI2_DP LAN_MDI2_DN LAN_MDI3_DP LAN_MDI3_DN LAN_LED_100_N LAN_LED_1000_N LAN1 / LAN2 LAN_LED_LINK_N V3P3A_RTL Page: 3-39 SE-N207 SERIES USER MANUAL...

  • Page 67: Sr-N207-Gzz-3 I/O Add-On Board Top View

    SR-N207-GZZ-3 I/O Add-On Board Connector and Jumpers List Jumper Description NAME COM Port Connector COM1, COM2 Jumper Description NAME COM1 and COM2 PIN9 Definition JP_COM1, JP_COM2 Selection Guide COM1 and COM2 RS-232/422/485 Mode Selection SW1, SW2 Guide Page: 3-40 SE-N207 SERIES USER MANUAL...
  • Page 68 Chapter 3 System Configuration COM Port Connector (COM1, COM2) Port Location: COM1, COM2 Description: COM1/COM2 (RS-232/RS-422/RS-485) Connector ASSIGNMENT RS232 RS422 RS485 (Default Setting) COM_DCDJ_I RS-485- COM_RX_I RS-485+ COM1 / COM2 COM_TX_I COM_DTJ_I COM_DSRJ_I COM_RTSJ_I COM_CTSJ_I COM_RI_SEL Page: 3-41 SE-N207 SERIES USER MANUAL...

  • Page 69: Jp_Com2

    COM1 and COM2 PIN9 Definition Selection Guide (JP_COM1, JP_COM2) Jumper Location: JP_COM1, JP_COM2 Description: COM1 pin9 (JP_COM1) and COM2 pin9 (JP_COM2) RI/5V/12V Selection SELECTION JUMPER SETTING JUMPER ILLUSTRATION (Default Setting) JP_COM1 JP_COM2 +12V JP_COM1 JP_COM2 JP_COM1 JP_COM2 Page: 3-42 SE-N207 SERIES USER MANUAL...
  • Page 70 Chapter 3 System Configuration COM1 and COM2 RS-232/422/485 Mode Selection (SW1, SW2) Jumper Location: SW1, SW2 Description: COM1, COM2 RS-232/422/485 mode selection SELECTION SW1 / SW2 SETTING RS-232 (Default Setting) SW1/SW2 RS-422 SW1/SW2 RS-485 SW1/SW2 Page: 3-43 SE-N207 SERIES USER MANUAL...

  • Page 71: Sr-N207-Gzz-4 I/O Add-On Board Top View

    SR-N207-GZZ-4 I/O Add-On Board Connectors and Jumper List Connector Description NAME COM Port Connector COM3, COM4, COM5, COM6 Jumper Description NAME COM3, COM4, COM5 and COM6 RS-232/422/485 SW2, SW3, SW4, SW5 Mode Selection Guide Page: 3-44 SE-N207 SERIES USER MANUAL...

  • Page 72: Com Port Connector (Com3, Com4)

    COM_CTSJ_I COM_RI_R COM Port Connector (COM5, COM6) Port Location: COM5, COM6 Description: COM5/COM6 (RS-232/RS-422/RS-485) Connector ASSIGNMENT RS232 RS422 RS485 (Default Setting) COM_DCDJ_I RS-485- COM_RX_I RS-485+ COM5 / COM6 COM_TX_I COM_DTJ_I COM_DSRJ_I COM_RTSJ_I COM_CTSJ_I COM_RI_R Page: 3-45 SE-N207 SERIES USER MANUAL...

  • Page 73: Slide Switch For Com3, Com4, Com5 And Com6

    Jumper Location: SW2, SW3, SW4, SW5 Description: Slide Switch for COM3, COM4, COM5, COM6 RS-232/422/485 selection SELECTION SW2, SW3, SW5 SETTING RS-232 (Default Setting) SW2, SW3, SW5 RS-422 SW2, SW3, SW5 RS-485 SW2, SW3, SW5 Page: 3-46 SE-N207 SERIES USER MANUAL...

  • Page 74: Sr-N207-Gzz-5 I/O Add-On Board Top View

    SR-N207-GZZ-5 I/O Add-On Board Top View 3.5.11 SR-N207-GZZ-5 I/O Add-On Board Connector USB 2.0 Connectors (USB1, USB2, USB3) Port Location: USB1, USB2, USB3 Description: USB1, USB2, USB3 Connector ASSIGNMENT V5P0S_USB1 USB_DN USB_DP USB1 / USB2 / USB3 Page: 3-47 SE-N207 SERIES USER MANUAL...

  • Page 75: Sr-N207-Gzz-6 I/O Add-On Board Top View

    Chapter 3 System Configuration 3.5.12 SR-N207-GZZ-6 I/O Add-On Board Top View PRINT1 JIOCON1 3.5.13 SR-N207-GZZ-6 I/O Add-On Board Connector Printer Port Connector Port Location: PRINT1 Description: Printer Port Connector PRINT1 ASSIGNMENT ASSIGNMENT STRBJ AFDJ ERRJ INITJ SLCTINJ Page: 3-48 SE-N207 SERIES USER MANUAL...
  • Page 76 Chapter 3 System Configuration ASSIGNMENT ASSIGNMENT ACKJ BUSY SLCTJ Page: 3-49 SE-N207 SERIES USER MANUAL...

  • Page 77: Sr-N207-Gzz-7 I/O Add-On Board Top View

    Chapter 3 System Configuration 3.5.14 SR-N207-GZZ-7 I/O Add-On Board Top View 3.5.15 SR-N207-GZZ-7 I/O Add-On Board Connectors CANBus Connectors (CAN1, CAN2) Port Location: CAN1, CAN2 Description: CAN1, CAN2 Connector ASSIGNMENT CANL CAN1 / CAN2 CANH V5P0S_ISO Page: 3-50 SE-N207 SERIES USER MANUAL...

  • Page 78: Sr-N207-Gzz-8 Pse Board Top View

    Chapter 3 System Configuration 3.5.16 SR-N207-GZZ-8 PSE Board Top View PSE_LED1 PSE_LED2 3.5.17 SR-N207-GZZ-8 PSE Board Bottom View Page: 3-51 SE-N207 SERIES USER MANUAL...

  • Page 79: Sr-N207-Gzz-8 Pse Board Connectors

    SR-N207-GZZ-8 PSE Board Connectors PSE Connector (JP1) Connector Location: JP1 Description: JP1 Connector (rear side) PIN ASSIGNMENT PIN ASSIGNMENT V3P3S V3P3A V12P0A_L 10 V54P0A V12P0A_L 12 V54P0A 11 V12P0A_L 14 OUT2 13 V12P0A_L 16 OUT1 15 V12P0A_L Page: 3-52 SE-N207 SERIES USER MANUAL...
  • Page 80 Chapter 3 System Configuration PSE Link LED Connectors (PSE_LED1, PSE_LED2) Connector Location: PSE_LED1, PSE_LED2 Description: PSE link LED Connector (top side) ASSIGNMENT Power PSE_LED1/ PSE_LED2 Page: 3-53 SE-N207 SERIES USER MANUAL...

  • Page 81: Sr-N207-Gzz-9 Pse Board Top View

    Chapter 3 System Configuration 3.5.19 SR-N207-GZZ-9 PSE Board Top View PD_LED1 PD_LED2 3.5.20 SR-N207-GZZ-9 PSE Board Bottom View JPD1 Page: 3-54 SE-N207 SERIES USER MANUAL...

  • Page 82: Sr-N207-Gzz-9 Pd Board Connectors

    SPAER1_B TXCT_B 10 SPAER2_B RXCT_B 12 GND (+V12P0A_L) 14 GND (+V12P0A_L) JPD1 16 GND (+V12P0A_L) PD LED Connectors (PD_LED1, PD_LED2) Connector Location: PD_LED1, PD_LED2 Description: PD LED Connector (top side) ASSIGNMENT Power PD_LED1/ PD_LED2 Page: 3-55 SE-N207 SERIES USER MANUAL...

  • Page 83: Sr-N207-Gzz-10 Pd Board Top View

    LAN with PSE Connectors (LAN1, LAN2) Connector Location: LAN1, LAN2 Description: LAN1/LAN2 Connectors with PSE ASSIGNMENT LAN_MDI0_DP LAN_MDI0_DN LAN_MDI1_DP LAN_MDI1_DN LAN_MDI2_DP LAN_MDI2_DN LAN_MDI3_DP LAN_MDI3_DN V54P0A LAN1_LED_LINK_N V3P3A_RTL1 LAN1_LED_100_N L3 L4 LAN1_LED_1000_N LAN1 / LAN2 Page: 3-56 SE-N207 SERIES USER MANUAL...

  • Page 84: Poe Power Connector (Jpower1)

    Chapter 3 System Configuration POE Power Connector (JPOWER1) Connector Location: JPOWER1 Description: POE Power Connector ASSIGNMENT JPOWER1 PSE Link LED Connectors (PSE_LED1, PSE_LED2) Connector Location: PSE_LED1, PSE_LED2 Description: PSE link LED Connector ASSIGNMENT Power PSE_LED1/ PSE_LED2 Page: 3-57 SE-N207 SERIES USER MANUAL...

  • Page 85: Software Utilities

    • Installing LAN Driver Utility • Installing Sound Driver Utility • Installing Intel ® Serial IO Driver Utility • Installing FTDI ® USB to Serial Driver Utility • Installing FINTEK ® F81601 PCIE to CANBus Driver Utility SE-N207 SERIES USER MANUAL Page: 4-1...

  • Page 86: Introduction

    Chapter 4 Software Utilities 4.1 Introduction Enclosed with the SE-N207 Series package is our driver utilities contained in a DVD-ROM disk. Refer to the following table for driver locations: Filename (Assume that DVD Purpose OS Win10 ROM drive is D :)

  • Page 87: Installing Intel Chipset Software Installation Utility

    The utility pack is to be installed only for Windows 10 series, and it should be installed immediately after the OS installation is finished. Please follow the steps below: Connect the USB DVD-ROM device to SE-N207 and insert the driver disk. Open the 1_Main Chip folder.

  • Page 88: Intel ® Management Engine Components Installer

    Management Engine Components Installer Installation To install the Management Engine Components driver utility, follow the steps below: Connect the USB DVD-ROM device to SE-N207 and insert the driver disk. Open the 4_ME folder. Enter the Win10(64Bit) folder where the ME driver is located.

  • Page 89: Installing Raid Driver Utility

    Chapter 4 Software Utilities 4.4 Installing RAID Driver Utility To install the RAID driver utility, follow the steps below: Connect the USB DVD-ROM device to SE-N207 and insert the driver disk. Open the 7_RAID folder. Enter the Win10(64Bit) folder where the RAID driver is located.

  • Page 90: Installing Graphics Driver Utility

    Chapter 4 Software Utilities 4.5 Installing Graphics Driver Utility The graphics interface embedded in SE-N207 can support a wide range of display types. You can have dual displays via HDMI / DVI-I ports and make the system work simultaneously. To install the Graphics driver utility, follow the steps below: Connect the USB DVD-ROM device to SE-N207 and insert the driver disk.

  • Page 91: Installing Lan Driver Utility

    To install the Intel Ethernet connection I219-LM for LAN driver, follow the steps below: Connect the USB DVD-ROM device to SE-N207 and insert the driver disk. Open the 5_LAN Chip folder. Enter the I219-LM folder where the driver is located.

  • Page 92: Installing Sound Driver Utility

    4.7 Installing Sound Driver Utility The sound function enhanced in this system is fully compatible. To install the Sound driver, follow the steps below: Connect the USB DVD-ROM device to SE-N207 and insert the driver disk. Open the 3_Sound folder.

  • Page 93: Installing Intel Serial I/O Driver Utility

    4.8 Installing Intel Serial I/O Driver Utility To install the Serial I/O driver, follow the steps below: Connect the USB DVD-ROM device to SE-N207 and insert the driver disk. Open the 6_Serial IO folder. Enter the Win10(64Bit) folder where the driver is located.

  • Page 94: Installing Ftdi Usb To Serial Driver

    USB to Serial Driver ® To install the FTDI USB to Serial driver, follow the steps below: Connect the USB DVD-ROM device to SE-N207 and insert the driver disk. Open the Daughter board folder. Enter the SR-N207-41N folder where the driver is located.

  • Page 95: Installing Fintek F81601 Pcie To Canbus Driver

    ® To install the FINTEK F81601 PCIE to CANBus driver, follow the steps below: Connect the USB DVD-ROM device to SE-N207 and insert the driver disk. Open the Daughter board folder Enter the SR-N207-71N folder where the driver is located.

  • Page 96: Api Package Content

    Driver to Control I2C. Driver to open XML multilangXML.dll file XML file to initiate Initial.xml the API Package API program ProxAP.exe executable file XML Files\Model XML file for each Name*\Initial.xml model Version.ini Version information SE-N207 SERIES USER MANUAL Page: 4-12...

  • Page 97: I/O Control

    Source Code 4.11.1 I/O Control The API Package program demonstrates how to use the API Library in a user’s application.  This program developed by VB.NET requires Microsoft .NET Framework version 2.0 or above. SE-N207 SERIES USER MANUAL Page: 4-13...
  • Page 98 When working with a 4in/ 4out type, fill in “0F”. (i.e. the later 4 bits indicate the I/O pin positions to be controlled) Bit3(IO3) Bit2(IO2) Bit1(IO1) Bit0(IO0) Tap to output the value of Dout Value to the hardware. [Write] SE-N207 SERIES USER MANUAL Page: 4-14...

  • Page 99: Watch Dog

    Chapter 4 Software Utilities Tap to read the input signal value and show the value to the Result [Read] field. The input signal value will be displayed in hex after [Read] is Result tapped. 4.11.2 Watch Dog SE-N207 SERIES USER MANUAL Page: 4-15...

  • Page 100: Digital I/O Function

    Purpose Initialize Digital API Package. Value None Return True (1) on success, False (0) on failure  Before using the API Package, this function should be called to pass XML variables to the DLL. SE-N207 SERIES USER MANUAL Page: 4-16...
  • Page 101 True (1) on success, False (0) on failure Digital_Get short Digital_Get (void); Purpose Get the digital input signal. Value None Return Digital input pin logic state Example Short data; data = Digital_Get( ); // DIN data, High/ Low input status SE-N207 SERIES USER MANUAL Page: 4-17...

  • Page 102: Watch Dog Function

    Stop the watchdog timer. Value None Return True (1) on success, False (0) on failure Watchdog_Recount bool Watchdog_Recount (void) Purpose Restart the watchdog timer. Value None Return True (1) on success, False (0) on failure SE-N207 SERIES USER MANUAL Page: 4-18...

  • Page 103: I2C Function

    Write data into the I2C Value SlaveID Device Slave address to be read Index Device data index to be read Data (Data to be written) Return True (1) on success, False (0) on failure SE-N207 SERIES USER MANUAL Page: 4-19...

  • Page 104: Bios Setup

    The BIOS Setup Utilities consist of the following menu items: • Accessing Setup Utilities • Main Menu • Advanced Menu • Chipset Menu • Security Menu • Boot Menu • Save & Exit Menu SE-N207 SERIES USER MANUAL Page: 5-1...

  • Page 105: Introduction

    Chapter 5 BIOS Setup 5.1 Introduction The SE-N207 System uses an AMI (American Megatrends Incorporated) Aptio BIOS that is stored in the Serial Peripheral Interface Flash Memory (SPI Flash) and can be updated. The SPI Flash contains the built-in BIOS setup program, Power-On Self-Test (POST), PCI auto-configuration utility, LAN EEPROM information, and Plug and Play support.
  • Page 106 BIOS setup menu by pressing <Del> or <Esc> immediately while the POST message is running before the operating system is loading. All the menu settings are described in details in this chapter. SE-N207 SERIES USER MANUAL Page: 5-3...

  • Page 107: Accessing Setup Utility

    Self-Test (POST) routines and the POST message will be displayed: Figure 5-2. POST Screen with AMI Logo Press <Del> or <Esc> to access the Setup Utility program and the Main menu of the Aptio Setup Utility will appear on the screen as below: SE-N207 SERIES USER MANUAL Page: 5-4...
  • Page 108 Description Navigation Key Select a different menu screen (move the <←> and <→> cursor from the selected menu to the left or right). <↑> and <↓> Select a different item (move the cursor from SE-N207 SERIES USER MANUAL Page: 5-5...
  • Page 109 Load the previous configuration values. <F3> Load the default configuration values. Save the current values and exit the BIOS <F4> setup menu. Close the sub-menu. <Esc> Trigger the confirmation to exit BIOS setup menu. SE-N207 SERIES USER MANUAL Page: 5-6...

  • Page 110: Main

    Displays the date of current BIOS version. Time Name No changeable options Displays the name of the PCH. PCH SKU No changeable options Displays the SKU for the PCH. Stepping No changeable options Displays the stepping of the PCH SE-N207 SERIES USER MANUAL Page: 5-7...
  • Page 111 The “Day” is automatically changed. Sets the system time. The format is [Hour: Minute: Second]. Users can directly enter System Time Hour, minute, second values or use <+> or <-> arrow keys to increase/decrease it. SE-N207 SERIES USER MANUAL Page: 5-8...

  • Page 112: Advanced

    Super IO Watchdog Parameters. S5 RTC Wake Settings Sub-Menu S5 RTC Wake Parameters. Super IO Sub-Menu System Super IO Chip Parameters Configuration USB Configuration Sub-Menu USB Configuration Parameters. Network Stack Sub-Menu Network Stack Settings. Configuration SE-N207 SERIES USER MANUAL Page: 5-9...

  • Page 113: Advanced - Cpu Configuration

    Reports if Intel Secure Mode Extensions Technology (SMX) SMX/TXT No changeable options /Trusted Execution Technology (TXT) is supported by the processor. Intel (VMX) - Disabled When enabled, a VMM can utilize the Virtualization - Enabled additional hardware capabilities SE-N207 SERIES USER MANUAL Page: 5-10...
  • Page 114 - Disabled Hyper-Threading parallelization of computation - Enabled performed on PC microprocessor. For each processor core that is physically present, the operating system addresses two virtual processors, and shares the workload between them when possible. SE-N207 SERIES USER MANUAL Page: 5-11...

  • Page 115: Advanced - Pch-Fw Configuration

    Displays the ME Firmware Version. Version ME Firmware Mode No changeable options Displays the ME Firmware Mode. ME Firmware SKU No changeable options Displays the ME Firmware SKU. PTT Configuration Sub-Menu PTT Configuration Parameters. SE-N207 SERIES USER MANUAL Page: 5-12...

  • Page 116: Advanced - Pch-Fw Configuration - Ptt Configuration

    - Enables PTT in SkuMgr dTPM 1.2 - dTPM - Disables PTT in SkuMgr Warning ! TPM Device Selection - PTT PTT/dTPM will be disabled and all data saved on it will be lost. SE-N207 SERIES USER MANUAL Page: 5-13...

  • Page 117: Advanced - Trusted Computing

    BIOS Setting Options Description/Purpose Enables or Disables BIOS support for - Disable security device. O.S. will not show Security Security Device Support - Enable Device. TCG EFI Protocol and INT1A interface will not be available. SE-N207 SERIES USER MANUAL Page: 5-14...

  • Page 118: Advanced - Acpi Settings

    SUSPEND button is - S3 (Suspend to RAM) pressed. Lock Legacy - Disabled Enables or Disables Lock of Legacy Resources - Enabled Resources. - Disabled S3 Video Repost Enables or Disables S3 Video Repost. - Enabled SE-N207 SERIES USER MANUAL Page: 5-15...

  • Page 119: Advanced - Hardware Monitor

    VCC3V No changeable options Detects and displays 3V voltage. VSB3V No changeable options Detects and displays VSB3V voltage. Detects and displays the voltage level VSB5V No changeable options of the VSB5V in supply. SE-N207 SERIES USER MANUAL Page: 5-16...

  • Page 120: Smart Fan Mode Configuration

    - Manual Duty Mode Smart Fan Mode for CPU Control - Auto Duty-Cycle Mode Fan. Manual mode fan control, user can Manual Duty Mode Numeric (from 1 to 100) write expected duty cycle (PWM fan type) 1-100. SE-N207 SERIES USER MANUAL Page: 5-17...

  • Page 121: Advanced -Super Io Watchdog

    Selects 1s (second) or 60s (minute) as Watchdog timer unit - 60s the time unit of Watchdog timer. Count for Timer Numeric Sets the timeout for Watchdog timer. (Seconds) (from 1 to 255) (Max. value: 255 seconds or minutes) SE-N207 SERIES USER MANUAL Page: 5-18...

  • Page 122: Advanced -S5 Rtc Wake Settings

    - Disabled • Fixed Time: System will wake on the Wake system from S5 - Fixed Time hr::min::sec specified. - Dynamic Time • Dynamic Time: System will wake on the current time + Increase minute(s). SE-N207 SERIES USER MANUAL Page: 5-19...
  • Page 123 Sets a minute for schedule Wake up minute Multiple options ranging from 0 to 59 power on event. Sets a second for schedule Wake up second Multiple options ranging from 0 to 59 power on event. SE-N207 SERIES USER MANUAL Page: 5-20...
  • Page 124 + Increase minute(s). Sets a period of time (in Wake up minute Multiple options ranging from 1 to 5 minutes) after which the board increase wakes up from S5 state. SE-N207 SERIES USER MANUAL Page: 5-21...

  • Page 125: Advanced -Super Configuration

    Set Parameters of Serial Port 4 (COMD) Serial Port 5 Configuration Sub-menu Set Parameters of Serial Port 5 (COME) Serial Port 6 Configuration Sub-menu Set Parameters of Serial Port 6 (COMF) Parallel Port Sub-menu Set Parameters of Parallel Port (LPT) SE-N207 SERIES USER MANUAL Page: 5-22...
  • Page 126 Allows you to select specific - IO=3F8h; IRQ=3,4,5,7,10,11; Possible IO address and IRQ for Serial - IO=2F8h; IRQ=3,4,5,7,10,11; Port 1. - IO=3E8h; IRQ=3,4,5,7,10,11; - IO=2E8h; IRQ=3,4,5,7,10,11; - RS-232 Mode - RS-422 Select COM mode - RS-485 SE-N207 SERIES USER MANUAL Page: 5-23...
  • Page 127 Allows you to select specific - IO=3F8h; IRQ=3,4,5,7,10,11; Possible IO address and IRQ for Serial - IO=2F8h; IRQ=3,4,5,7,10,11; Port 2. - IO=3E8h; IRQ=3,4,5,7,10,11; - IO=2E8h; IRQ=3,4,5,7,10,11; - RS-232 Mode - RS-422 Select COM mode - RS-485 SE-N207 SERIES USER MANUAL Page: 5-24...
  • Page 128 Allows you to select specific - IO=3F8h; IRQ=3,4,5,7,10,11; Possible IO address and IRQ for Serial - IO=2E8h; IRQ=3,4,5,7,10,11; Port 3. - IO=2F0h; IRQ=3,4,5,7,10,11; - IO=2E0h; IRQ=3,4,5,7,10,11; - RS-232 Mode - RS-422 Select COM mode - RS-485 SE-N207 SERIES USER MANUAL Page: 5-25...
  • Page 129 Serial Port 4. - Auto - IO=2E8h; IRQ=6; Allows you to select specific - IO=3E8h; IRQ=3,4,5,7,10,11; Possible IO address and IRQ for Serial - IO=2E8h; IRQ=3,4,5,7,10,11; Port 4. - IO=2F0h; IRQ=3,4,5,7,10,11; - IO=2E0h; IRQ=3,4,5,7,10,11; SE-N207 SERIES USER MANUAL Page: 5-26...
  • Page 130 Serial Port 5. - Auto - IO=2F0h; IRQ=10; Allows you to select specific - IO=3F8h; IRQ=3,4,5,7,10,11; Possible IO address and IRQ for Serial - IO=2E8h; IRQ=3,4,5,7,10,11; Port 5. - IO=2F0h; IRQ=3,4,5,7,10,11; - IO=2E0h; IRQ=3,4,5,7,10,11; SE-N207 SERIES USER MANUAL Page: 5-27...
  • Page 131 Serial Port 6. - Auto - IO=2E0h; IRQ=11; Allows you to select specific - IO=3F8h; IRQ=3,4,5,7,10,11; Possible IO address and IRQ for Serial - IO=2E8h; IRQ=3,4,5,7,10,11; Port 6. - IO=2F0h; IRQ=3,4,5,7,10,11; - IO=2E0h; IRQ=3,4,5,7,10,11; SE-N207 SERIES USER MANUAL Page: 5-28...
  • Page 132 Mode - EPP-1.7 and SPP Mode DMA resource. After Mode - ECP Mode changing, Reset the System to - ECP and EPP 1.9 Mode reflect actual device settings. - ECP and EPP 1.7 Mode SE-N207 SERIES USER MANUAL Page: 5-29...

  • Page 133: Advanced - Usb Configuration

    The USB Configuration allows users to configure advanced USB settings such as USB mass storage driver support. USB Configuration Screen BIOS Setting Options Description/Purpose USB Mass Storage - Disabled Enable/Disable USB Mass Storage Driver Driver Support - Enabled Support. SE-N207 SERIES USER MANUAL Page: 5-30...

  • Page 134: Advanced - Network Stack Configuration

    - Enabled be created. Enables IPv6 PXE Boot Support. If - Disabled Ipv6 PXE Support disabled, IPv6 PXE boot option will not - Enabled be created. IPSEC Certificate - Disabled Support to Enable/Disable IPSEC SE-N207 SERIES USER MANUAL Page: 5-31...
  • Page 135 PXE boot wait time Numeric (from 0 to 5) to abort after the Esc key is pressed. Number of times that the media presence Media detect count Numeric (from 1 to 50) will be checked. SE-N207 SERIES USER MANUAL Page: 5-32...

  • Page 136: Chipset

    This menu allows users to configure advanced Chipset settings such as System Agent (SA) and PCH-IO configuration parameters. Chipset Screen BIOS Setting Options Description/Purpose System Agent (SA) Sub-menu System Agent (SA) parameters. Configuration PCH-IO Configuration Sub-menu PCH parameters. SE-N207 SERIES USER MANUAL Page: 5-33...

  • Page 137: Chipset - System Agent (Sa) Configuration

    - DP activated during post. DISPLAY port 2 type - HDMI Select the video device which will be selection - DP activated during post. - Disabled VT-d Enables or Disables VT-d function. - Enabled SE-N207 SERIES USER MANUAL Page: 5-34...

  • Page 138: Chipset - Sa Configuration - Memory Configuration

    Memory Configuration Screen BIOS Setting Options Description/Purpose Memory Frequency No changeable options Displays the Frequency of Memory. DIMM1 No changeable options Displays the size of DIMM1. DIMM2 No changeable options Displays the size of DIMM2. SE-N207 SERIES USER MANUAL Page: 5-35...

  • Page 139: Chipset - Pch-Io Configuration

    SATA Configuration settings. Configuration - Disabled PCH LAN Controller Enables or Disables onboard NIC. - Enabled - Disabled Enables or Disables integrated LAN to Wake on LAN Enable - Enabled wake up the system. Default: Enabled. SE-N207 SERIES USER MANUAL Page: 5-36...
  • Page 140 BIOS Setting Options Description/Purpose Specifies the Power On/Off state that the - Power On system will go into when the power is State After G3 - Power Off re-applied following a power failure (G3 state). SE-N207 SERIES USER MANUAL Page: 5-37...

  • Page 141: Chipset - Pch-Io Configuration - Pci Express Configuration

    The PCI Express Configuration allows users to configure PCI Port assigned to LAN. PCI Express Configuration Screen BIOS Setting Options Description/Purpose PCIE Port assigned to No changeable options Displays the LAN assigned PCIE Port. SE-N207 SERIES USER MANUAL Page: 5-38...

  • Page 142: Chipset - Pch-Io Configuration - Sata Configuration

    SATA Mode Selection - RST operate. Serial ATA Port 0 – 1 No changeable options Displays the SATA device’s name. - Disabled Port 0 - 1 Enables or Disables SATA Port Device. - Enabled SE-N207 SERIES USER MANUAL Page: 5-39...
  • Page 143 Chapter 5 BIOS Setup BIOS Setting Options Description/Purpose Enables or Disables Hot Plug function - Disabled HotPlug to designate a SATA port device as - Enabled hot-pluggable. SE-N207 SERIES USER MANUAL Page: 5-40...

  • Page 144: Security

    Setup utility. Security Screen BIOS Setting Options Description/Purpose Administrator Password can be 3-20 Specifies the administrator password. Password alphanumeric characters. Password can be 3-20 User Password Specifies the user password. alphanumeric characters. SE-N207 SERIES USER MANUAL Page: 5-41...
  • Page 145 2. Select the configured Administrator Password or User Password that you want to delete. Leave the dialog box blank and press <Enter>. 3. Press <Enter> again when the password confirmation box appears. SE-N207 SERIES USER MANUAL Page: 5-42...

  • Page 146: Boot

    • On: Enables the NumLock function Bootup - On automatically after the system is NumLock State - Off powered on. • Off: Disables the NumLock function after the system is powered on. SE-N207 SERIES USER MANUAL Page: 5-43...
  • Page 147 Allows users to change the boot order from the available device(s). Note that in Boot Option - [Drive(s)] the menu displayed, you will only see the #1~#n - Disabled device with the highest priority for a specific boot device type. SE-N207 SERIES USER MANUAL Page: 5-44...

  • Page 148: Save & Exit

    Discard Changes and Reset to discard any changes you have made and restore the factory BIOS defaults. Restore Defaults You may simply press F3 at any time to load the optimized values which resets all BIOS settings to the factory defaults. Save & Exit Screen SE-N207 SERIES USER MANUAL Page: 5-45...
  • Page 149 Saves the changes done so far as User Save as User Defaults No changeable options Defaults. Loads the optimized defaults for BIOS Restore Defaults No changeable options settings. Forces to boot the system from Boot Override - [Drive(s)] selected [drive(s)]. SE-N207 SERIES USER MANUAL Page: 5-46...

  • Page 150: Appendix A System Diagram

    SE-N207 system. • SE-N207 System Exploded Diagram • SE-N207 Rear View (For 4 x COM sku) • SE-N207 Rear View (For 2 x PoE LAN sku) SE-N207 SERIES USER MANUAL Page: A-1...

  • Page 151: Se-N207 System Exploded Diagram (With Rear View 2 X I/O Slot Sku

    Appendix A System Diagram SE-N207 System Exploded Diagram (with rear view 2 x I/O Slot SKU) Page: A-3 SE-N207 SERIES USER MANUAL...

  • Page 152: Se-N207 Rear View (For 4 X Com Sku

    Appendix A System Diagram SE-N207 Rear View (For 4 x COM sku) SE-N207 Rear View (For 2 x PoE LAN sku) Page: A-3 SE-N207 SERIES USER MANUAL...

  • Page 153: Appendix B Technical Summary

    This appendix will give you a brief introduction of the allocation maps for the system resources. The following topics are included: • System Block Diagram • Interrupt Map • I/O Map • Memory Map • Configuring WatchDog Timer • Flash BIOS Update SE-N207 SERIES USER MANUAL Page: B-1...
  • Page 154 RS232/422/485 (SLB9665TT2.0-5.51) COM 2 LPC SLOT(DEBUG PORT) RS232/422/485 HW monitor FINTEK COM 3 Selection 1 RS232/422/485 LPC SIO COM 4 Selection 1 F81866AD-I RS232/422/485 COM 5 Selection 2 RS232 COM 6 Selection 2 RS232 Page: B-2 SE-N207 SERIES USER MANUAL...
  • Page 155 IRQ 58 Microsoft ACPI-Compliant System IRQ 59 Microsoft ACPI-Compliant System IRQ 60 Microsoft ACPI-Compliant System IRQ 61 Microsoft ACPI-Compliant System IRQ 62 Microsoft ACPI-Compliant System IRQ 63 Microsoft ACPI-Compliant System IRQ 64 Microsoft ACPI-Compliant System Page: B-3 SE-N207 SERIES USER MANUAL...
  • Page 156 IRQ 88 Microsoft ACPI-Compliant System IRQ 89 Microsoft ACPI-Compliant System IRQ 90 Microsoft ACPI-Compliant System IRQ 91 Microsoft ACPI-Compliant System IRQ 92 Microsoft ACPI-Compliant System IRQ 93 Microsoft ACPI-Compliant System IRQ 94 Microsoft ACPI-Compliant System Page: B-4 SE-N207 SERIES USER MANUAL...
  • Page 157 IRQ 118 Microsoft ACPI-Compliant System IRQ 119 Microsoft ACPI-Compliant System IRQ 120 Microsoft ACPI-Compliant System IRQ 121 Microsoft ACPI-Compliant System IRQ 122 Microsoft ACPI-Compliant System IRQ 123 Microsoft ACPI-Compliant System IRQ 124 Microsoft ACPI-Compliant System Page: B-5 SE-N207 SERIES USER MANUAL...
  • Page 158 IRQ 148 Microsoft ACPI-Compliant System IRQ 149 Microsoft ACPI-Compliant System IRQ 150 Microsoft ACPI-Compliant System IRQ 151 Microsoft ACPI-Compliant System IRQ 152 Microsoft ACPI-Compliant System IRQ 153 Microsoft ACPI-Compliant System IRQ 154 Microsoft ACPI-Compliant System Page: B-6 SE-N207 SERIES USER MANUAL...
  • Page 159 IRQ 178 Microsoft ACPI-Compliant System IRQ 179 Microsoft ACPI-Compliant System IRQ 180 Microsoft ACPI-Compliant System IRQ 181 Microsoft ACPI-Compliant System IRQ 182 Microsoft ACPI-Compliant System IRQ 183 Microsoft ACPI-Compliant System IRQ 184 Microsoft ACPI-Compliant System Page: B-7 SE-N207 SERIES USER MANUAL...
  • Page 160 IRQ 259 Microsoft ACPI-Compliant System IRQ 260 Microsoft ACPI-Compliant System IRQ 261 Microsoft ACPI-Compliant System IRQ 262 Microsoft ACPI-Compliant System IRQ 263 Microsoft ACPI-Compliant System IRQ 264 Microsoft ACPI-Compliant System IRQ 265 Microsoft ACPI-Compliant System Page: B-8 SE-N207 SERIES USER MANUAL...
  • Page 161 IRQ 289 Microsoft ACPI-Compliant System IRQ 290 Microsoft ACPI-Compliant System IRQ 291 Microsoft ACPI-Compliant System IRQ 292 Microsoft ACPI-Compliant System IRQ 293 Microsoft ACPI-Compliant System IRQ 294 Microsoft ACPI-Compliant System IRQ 295 Microsoft ACPI-Compliant System Page: B-9 SE-N207 SERIES USER MANUAL...
  • Page 162 IRQ 319 Microsoft ACPI-Compliant System IRQ 320 Microsoft ACPI-Compliant System IRQ 321 Microsoft ACPI-Compliant System IRQ 322 Microsoft ACPI-Compliant System IRQ 323 Microsoft ACPI-Compliant System IRQ 324 Microsoft ACPI-Compliant System IRQ 325 Microsoft ACPI-Compliant System Page: B-10 SE-N207 SERIES USER MANUAL...
  • Page 163 IRQ 349 Microsoft ACPI-Compliant System IRQ 350 Microsoft ACPI-Compliant System IRQ 351 Microsoft ACPI-Compliant System IRQ 352 Microsoft ACPI-Compliant System IRQ 353 Microsoft ACPI-Compliant System IRQ 354 Microsoft ACPI-Compliant System IRQ 355 Microsoft ACPI-Compliant System Page: B-11 SE-N207 SERIES USER MANUAL...
  • Page 164 IRQ 379 Microsoft ACPI-Compliant System IRQ 380 Microsoft ACPI-Compliant System IRQ 381 Microsoft ACPI-Compliant System IRQ 382 Microsoft ACPI-Compliant System IRQ 383 Microsoft ACPI-Compliant System IRQ 384 Microsoft ACPI-Compliant System IRQ 385 Microsoft ACPI-Compliant System Page: B-12 SE-N207 SERIES USER MANUAL...
  • Page 165 IRQ 409 Microsoft ACPI-Compliant System IRQ 410 Microsoft ACPI-Compliant System IRQ 411 Microsoft ACPI-Compliant System IRQ 412 Microsoft ACPI-Compliant System IRQ 413 Microsoft ACPI-Compliant System IRQ 414 Microsoft ACPI-Compliant System IRQ 415 Microsoft ACPI-Compliant System Page: B-13 SE-N207 SERIES USER MANUAL...
  • Page 166 IRQ 439 Microsoft ACPI-Compliant System IRQ 440 Microsoft ACPI-Compliant System IRQ 441 Microsoft ACPI-Compliant System IRQ 442 Microsoft ACPI-Compliant System IRQ 443 Microsoft ACPI-Compliant System IRQ 444 Microsoft ACPI-Compliant System IRQ 445 Microsoft ACPI-Compliant System Page: B-14 SE-N207 SERIES USER MANUAL...
  • Page 167 IRQ 469 Microsoft ACPI-Compliant System IRQ 470 Microsoft ACPI-Compliant System IRQ 471 Microsoft ACPI-Compliant System IRQ 472 Microsoft ACPI-Compliant System IRQ 473 Microsoft ACPI-Compliant System IRQ 474 Microsoft ACPI-Compliant System IRQ 475 Microsoft ACPI-Compliant System Page: B-15 SE-N207 SERIES USER MANUAL...
  • Page 168 IRQ 499 Microsoft ACPI-Compliant System IRQ 500 Microsoft ACPI-Compliant System IRQ 501 Microsoft ACPI-Compliant System IRQ 502 Microsoft ACPI-Compliant System IRQ 503 Microsoft ACPI-Compliant System IRQ 504 Microsoft ACPI-Compliant System IRQ 505 Microsoft ACPI-Compliant System Page: B-16 SE-N207 SERIES USER MANUAL...
  • Page 169 Intel(R) Ethernet Connection (6) I219-LM IRQ 4294967291 Intel(R) Management Engine Interface Intel(R) USB 3.1 eXtensible Host Controller - 1.10 IRQ 4294967292 (Microsoft) IRQ 4294967293 Intel(R) UHD Graphics 620 IRQ 4294967294 Standard SATA AHCI Controller Page: B-17 SE-N207 SERIES USER MANUAL...

  • Page 170: I/O Map

    Programmable interrupt controller 0x000000A4-0x000000A5 Programmable interrupt controller 0x000000A8-0x000000A9 Programmable interrupt controller 0x000000AC-0x000000AD Programmable interrupt controller 0x000000B0-0x000000B1 Programmable interrupt controller 0x000000B2-0x000000B3 Motherboard resources 0x000000B4-0x000000B5 Programmable interrupt controller 0x000000B8-0x000000B9 Programmable interrupt controller 0x000000BC-0x000000BD Programmable interrupt controller Page: B-18 SE-N207 SERIES USER MANUAL...
  • Page 171 Realtek PCIe GBE Family Controller 0x00004000-0x0000403F Intel(R) UHD Graphics 620 0x00004060-0x0000407F Standard SATA AHCI Controller 0x00004080-0x00004083 Standard SATA AHCI Controller 0x00004090-0x00004097 Standard SATA AHCI Controller 0x0000EFA0-0x0000EFBF Intel(R) SMBus - 9DA3 Intel(R) Active Management Technology - 0x0000FFF8-0x0000FFFF SOL (COM7) Page: B-19 SE-N207 SERIES USER MANUAL...
  • Page 172 Intel(R) UHD Graphics 620 0x90000000-0x9FFFFFFF Intel(R) UHD Graphics 620 0x90000000-0x9FFFFFFF PCI Express Root Complex 0xA11FB000-0xA11FBFFF Realtek PCIe GBE Family Controller 0xA11FC000-0xA11FFFFF Realtek PCIe GBE Family Controller 0xFE1F8000-0xFE1FBFFF High Definition Audio Controller 0xFCF00000-0xFCFFFFFF High Definition Audio Controller Page: B-20 SE-N207 SERIES USER MANUAL...
  • Page 173 PCI Express Root Complex 0xE0000-0xE3FFF PCI Express Root Complex 0xE4000-0xE7FFF PCI Express Root Complex 0xE4000-0xE7FFF PCI Express Root Complex 0xE8000-0xEBFFF PCI Express Root Complex 0xEC000-0xEFFFF PCI Express Root Complex 0xF0000-0xFFFFF PCI Express Root Complex 0x40000000-0x403FFFFF Motherboard resources Page: B-21 SE-N207 SERIES USER MANUAL...
  • Page 174 To exit the Extended Function Mode, writing 0xAA to the EFER is required. Once the chip exits the Extended Function Mode, it is in the normal running mode and is ready to enter the configuration mode. Page: B-22 SE-N207 SERIES USER MANUAL...
  • Page 175 ;---------------------------------Enable Watch dog feature ------------------------------ 030h ;------------------------------- Enable Watch PME-------------------------------------------- 0FAh ; ------------------------ Set timeout interval to 30 ------------------------------------------ 0F6h ;-------------------Set second as counting unit and start counting --------------------- 0F5h ;---------------------------------Exit the extended function mode ------------------------- 0AAh Page: B-23 SE-N207 SERIES USER MANUAL...
  • Page 176 (3) The system will go into the BIOS setup menu. (4) Select [Boot] and set the USB bootable device as the 1st boot device. (5) Press F4 to save the configuration and exit the BIOS setup menu. Page: B-24 SE-N207 SERIES USER MANUAL...
  • Page 177 Appendix B Technical Summary Page: B-25 SE-N207 SERIES USER MANUAL...
  • Page 178 BIOS ROM may be crashed and the system will be unable to boot up next time. After the BIOS update procedure is completed, the following messages will be shown: Page: B-26 SE-N207 SERIES USER MANUAL...
  • Page 179 Restart the system and boot up with the new BIOS configurations. The BIOS Update is completed after the system is restarted. Reboot the system and verify if the BIOS version shown on the initialization screen has been updated. Page: B-27 SE-N207 SERIES USER MANUAL...

Table of Contents