Control Explanation - IVT SNWB-163-RC Manual

∙
Never direct discharge at children, bystanders and
pets or allow anyone in front of the machine.
∙
Do not overload machine capacity by attempting to
clear snow at too fast of a rate.
∙ Always be sure of your footing and keep a firm hold
on the handles. Walk, never run.
∙ Disengage power to the auger when transporting
or not in use.
∙ Never operate machine at high transport speeds on
slipper surface. Look down and behind and use care
when in reverse.
∙ If the machine should start to vibrate abnormally,
stop the engine, disconnect the spark plug wire and
ground it against the engine. Inspect thoroughly for
damage.
∙
Disengage all controls and stop engine before
you leave the operating position (behind the handles).
Wait until the auger comes to a complete stop before
unclogging the chute assembly, making any adjustments
or inspections.
∙
Never touch a hot engine or muffler.
∙ Only operate the controls while the engine is
running.
∙
Never put your hand in the discharge or collector
openings. Always use the clean-out tool provided to
unclog the discharge opening. Do not unclog chute
assembly while engine is running. Shut off engine
and remain behind handles until all moving parts have
stopped before unclogging.
UNPACKING
When unpacking, check to make sure that all
components are included. Refer to the drawings on this
manual. If any parts are missing or broken, please call
an IVT assistance center.

CONTROL EXPLANATION

Drive control (1)
The drive control is located on the right handle. Squeeze
the drive control to engage the wheel drive. Release to
stop.
Shift lever (2)
The shift lever is used to determine both ground speed
and direction of travel. It can be moved into different
positions.
∙ Forward: your machine has some forward speeds,
with position number one being the slowest speed.
∙
Reverse: your machine has some reverse speeds,
with position number one being the slowest speed.
WARNING!
control before changing speeds.
Auger control (3)
The auger control (3) is located on the left handle.
Squeeze the auger control (3) to engage the augers (9).
Release to stop the snow throwing action (drive control
must also be released).
Chute directional control (4) and chute deflector
control (11)
The chute direction control (4) is located before the
panel of the snow blower, while chute deflector control
(11) is located on the panel.
∙
Rotate the chute directional control (4) right or left
to change the direction of snow out.
∙ Move the chute deflector control (11) back and front
to adjust the distance of snow throwing.
Skid shoe (8)
The space between the shave plate and the ground can
be adjusted by positioning the skid shoes (8).
Clean-out tool (10)
Clean-out tool (10) helps you to clean out the clogged
chute assembly, never use your hands.
Shut off the engine (5) and remain behind handles until
all moving parts have stopped before unclogging.
ASSEMBLY INSTRUCTIONS
Drive and auger control cable assembling [F1]
∙ Connect the moving control cable and auger control
cable to the right opening.
Dashboard assembling
∙
Put the dashboard to the lower handle of the
machine, and assemble them together with the bolts.
Shift lever (2) assembling [F2]
∙ Pull out the shift lever (2) out from the dashboard.
∙ Insert the angle side of shift lever (2) into the hole
on the lever to connect it to the transmission, and secure
it in place with the B pin.
∙
Bring the other side of the shift lever (2) to the hole
on the bottom part of the gear lever and secure it in
place with the B pin.
Control handles assembling [F3]
∙ Assemble the control handles to the panel. Bigger
one for shift lever (2) and smaller one for chute deflector
control (11).
9
Instruction manual
Always release drive
EN