Related Manuals for Hyundai HPP20V
Summary of Contents for Hyundai HPP20V
- Page 1 ORIGINAL INSTRUCTIONS IMPACT CORDLESS DRILL HPP20V READ THESE INSTRUCTIONS BEFORE USE THIS TOOL APPROVED BY DEKRA 19/06/17 Laurent Asty HYUNDAI 32, rue Aristide Bergès - ZI 31270 Cugnaux - France Licensed by Hyundai Corporation, Korea...
-
Page 2: Table Of Contents
CONTENTS SAFETY INSTRUCTIONS ABOUT YOUR PRODUCT USE AND FUNCTION MAINTENANCE AND STORAGE DISPOSAL CE DECLARATION... -
Page 3: Safety Instructions
1. SAFETY INSTRUCTIONS WARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. - Page 4 key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts.
- Page 5 Intended Use This power tool is designed for drilling as well as for tightening and loosening screws. Specially design to work with Hyundai range of battery and charger. This power tool should not be used for purposes other than those described.
- Page 6 Explantation of symbols Do not dispose of old appliances with domestic rubbish To reduce the risk of injury, the user must read and understand this manual before using this product. Conforms to relevant safety standards Do not expose batteries to temperatures exceeding 40 degrees.
- Page 7 2. YOUR PRODUCT a. Description 1. 1st/2nd gear switch lever 2. Torque adjustment ring driving/drilling/impact drilling 3. Keyless chuck 4. Chuck jaw setting 5. LED light 6. Reverse/forward switch 7. ON/OFF trigger switch 8. Hand grip 9. Battery release catch (on battery) 10.
- Page 8 This tool is provided without battery and battery charger. Please buy a battery pack (battery + charger) from the same trademark of this screwdriver. The recommended product is: HYUNDAI 20V LITHIUM ION BATTERY CHARGER. Do not use non recommended battery.
-
Page 9: About Your Product
b. Installation of the battery pack Warning! Always remove the battery from the tool when assembling accessories, making adjustments, during transport or when the tool is not in use. Remove the battery will prevent accidental starting which could cause severe personal injury. NOTE: To avoid serious personal injury, always remove the battery and keep your hands away from the lock button while transporting the tool. - Page 10 Incorrect installation of the battery may damage internal components c. Removing the battery pack Make sure that the forward/reverse switch is on its original position. Push and hold the battery release catch. Then slide the battery pack away from the tool.
-
Page 11: Use And Function
Tighten the chuck jaws on the drill bit. Make sure that the bit is well installed in place. Failure when installation will create accidents and injuries e. Removing bits Switch off the tool and put the reverse/forward switch in the center position. Open the chuck jaws and then pull the bit straight out. - Page 12 h. Two speed gear train This drill comes with 2 speed gear train to give high and low speed ranges. To change between the two speeds ranges, slide the selector switch located on the top of the drill. Use the low speed (1) for high power and torque applications and high speed (2) for fast drilling or driving applications.
- Page 13 Hammer action This drill has the additional feature of hammer action. Rotate the torque ring until the hammer symbol aligns with the arrow on the drill body. k. Working clamping To prevent the drill from spinning the workpiece if the drill bit becomes jammed in the hole being drilled, it is recommended that a drill vice or other suitable clamp is used to secure the workpiece during the drilling operation.
-
Page 14: Maintenance And Storage
4. MAINTENANCE AND STORAGE a. Maintenance Clean the housing only with a damp cloth. Do not use solvents! Then wipe thoroughly. Check the condition of the tool. If the tool is damaged or has malfunction, do not use it and bring it to a qualified service for inspection or reparation. To maintain the optimum battery power, we recommend that the battery be discharged and recharged every two months. -
Page 15: Ce Declaration
ZI, 32, rue Aristide Bergès- 31270 Cugnaux-France Tel: + 33 (0) 5.34.502.502 Fax: + 33 (0) 5.34.502.503 Declares that the machinery designated below: IMPACT CORDLESS DRILL HPP20V Serial number: Complies with the provisions of the Directive «machinery» 2006/42/CE and national laws transposing it:...