Advertisement
Read all safety warnings, instructions, illustrations and specifications provided with this power tool.
Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mainsoperated (corded) power tool or battery-operated (cordless) power tool.
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL | SIGNAL | MEANING |
DANGER: | Indicates a hazardous situation, which, if not avoided, will result in death or serious injury. | |
WARNING: | Indicates a hazardous situation, which, if not avoided, could result in death or serious injury. | |
CAUTION: | Indicates a hazardous situation, that, if not avoided, may result in minor or moderate injury. | |
NOTICE: | (Without Safety Alert Symbol) Indicates information considered important, but not related to a potential injury (e.g. messages relating to property damage). |
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the product better and safer.
SYMBOL | NAME | DESIGNATION/EXPLANATION |
Safety Alert | Indicates a potential personal injury hazard. | |
Read Operator's Manual | To reduce the risk of injury, user must read and understand operator's manual before using this product. | |
Eye Protection | Always wear eye protection with side shields marked to comply with ANSI Z87.1. | |
Wet Conditions Alert | Do not expose to rain or use in damp locations. | |
Recycle Symbol | This product uses lithium-ion (Li-ion) batteries. Local, state or federal laws may prohibit disposal of batteries in ordinary trash. Consult your local waste authority for information regarding available recycling and/or disposal options. | |
V | Volts | Voltage |
min | Minutes | Time |
Direct Current | Type or a characteristic of current | |
No Load Speed | Rotational speed, at no load | |
.../min | Per Minute | Revolutions, strokes, surface speed, orbits etc., per minute |
No Load Speed 0-450/0-1,750
Clutch 24-Position
Torque 515 in-lbs.
Hammer Speed (Blows per minute) 0-7,200 /0-28,000
Do not use this product if it is not completely assembled or if any parts appear to be missing or damaged. Use of a product that is not properly and completely assembled or with damaged or missing parts could result in serious personal injury.
Do not attempt to modify this product or create accessories or attachments not recommended for use with this product. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury.
If any parts are damaged or missing, please call 1-800-525-2579 for assistance.
Do not allow familiarity with this product to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious injury.
Always remove battery pack from the tool when you are assembling parts, making adjustments, cleaning, or when not in use. Removing battery pack will prevent accidental starting that could cause serious personal injury.
Always wear eye protection with side shields marked to comply with ANSI Z87.1. Failure to do so could result in objects being thrown into your eyes and other possible serious injuries.
Do not use any attachments or accessories not recommended by the manufacturer of this product. The use of attachments or accessories not recommended can result in serious personal injury.
You may use this product for the purposes listed below:
This drill is not intended to be used for mixing concrete, drywall, grout or other similar types of viscous mixtures. Failure to obey this caution could cause poor performance, possible injury, and will void your warranty.
The variable speed switch trigger delivers higher speed with increased trigger pressure and lower speed with decreased trigger pressure.
To turn the drill ON, depress the switch trigger. To turn it OFF, release the switch trigger and allow the chuck to come to a complete stop.
NOTE: A whistling or ringing noise coming from the switch during use is a normal part of the switch function.
NOTE: Running at low speeds under constant usage may cause the drill to become overheated. If this occurs, cool the drill by running it without a load and at full speed.
(FORWARD/REVERSE/CENTER LOCK)
See Figure 1.
Set the direction of rotation selector in the OFF (center lock) position to lock the switch trigger and help prevent accidental starting when not in use.
Position the direction of rotation selector to the left of the switch trigger for forward drilling. Position the selector to the right of the switch trigger to reverse the direction.
NOTE: The drill will not run unless the direction of rotation selector is pushed fully to the left or right.
NOTICE:
To prevent gear damage, always allow the chuck to come to a complete stop before changing the direction of rotation.
Battery tools are always in operating condition. Lock the switch when not in use or carrying at your side, when installing or removing the battery pack, and when installing or removing bits.
For complete charging instructions, see the operator's manuals for your battery pack and charger.
The arrows on the keyless chuck indicate which direction to rotate the chuck sleeve to tighten or release the drill bit.
Do not use a wrench to tighten or loosen the chuck jaws.
NOTICE:
Never change speeds while the tool is running. Failure to obey this caution could result in serious damage to the drill.
NOTE: If you have difficulty changing from one speed range to the other, turn the chuck by hand until the gears engage.
When using the hammer drill for various driving applications, beginning with a lower torque setting helps prevent the possibility of damaging screw heads, threads, workpiece, etc. In general, torque intensity should correspond to the screw diameter. If the torque is too high or the screws too small, the screws may be damaged or broken. The torque is adjusted by rotating the clutch torque and mode selector ring.
The torque is greater when the clutch torque and mode selector ring is set on a higher setting. The torque is less when the clutch torque and mode selector ring is set on a lower setting.
Rotate the adjustment ring to the proper torque setting for the type of material and size of screw you are using.
NOTE: This drill has an electric brake. When the switch trigger is released, the chuck stops turning. When the brake is functioning properly, sparks will be visible through the vent slots on the housing. This is normal and is the action of the brake.
NOTE: If an operation creates considerable dust resulting in low visibility of the workpiece, frequent vacuuming of the work area is recommended.
For maximum performance, use high speed steel bits for wood or metal drilling. Select drilling mode. Begin drilling at a very low speed to prevent the bit from slipping off the starting point.
Wood Drilling
Metal and Steel Drilling
For maximum performance, use carbide-tipped masonry impact bits or designated hammer drill bits when drilling holes in brick, tile, concrete, etc. Select hammer mode.
When servicing, use only identical replacement parts. Use of any other part could create a hazard or cause product damage.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and can be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc.
LED LIGHT FUNCTIONS
TOOL STATUS | LED LIGHT SCENARIO | ACTION REQUIRED |
Normal | Solid Light (No Flashes) | No Action Needed |
Low Battery | 3 Flashes | Replace Battery |
Excessive Force | 6 Flashes | Wait 5 Seconds |
Over Temperature | 9 Flashes | Let Tool Cool Off |
*More than 9 flashes will result in the need to remove the battery and reinsert a few minutes later.
REGISTER YOUR TOOLS
http://register.ryobiools.com
1-800-525-2579
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download Ryobi PCL220K2 - ONE+ 18V Cordless 1/2" Hammer Drill Manual
Advertisement
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the PCL220K2 that isn't answered in the manual? Leave your question here.