Accessories; Operating Location; Power Supply Connection; Microphone - Kenwood TS-600 Operating Manual

SS ee ee ee
: SECTION 2. INSTALLATION
{vet coun sctntb sce ctttbe-qtttD atnnbesettED scnADooetEED sata -cattbe- cate ctnED ecg sctattascnEED oc cantD LL AEN EEE sen eto HEAD oCLLLD UU ADDSCAEED "MEDD SATTED "UEDA EEED "TED ARTEL
2-1. ACCESSORIES
The Model TS-600 transceiver is supplied with the
following accessories. After unpacking, check the acces-
sories against the list:
Operating manual
RCA plug connector
Feet with screws ........-00 00 eee eee 2
Fuser tTAAG220V). isis nae ae eae 1
DPR CHIOV Siuigttns acorns gwittarels 1
SAMDCHOU RS 5 oaere aa cue 6% 1
GAS(DG CONE) ss 25 PO is eitistae 1
Microphone with hook, 500 ohm ........ 1
AC power cord with connector ..........- 1
DC power cord with connector .......... 1
VOX plug (installed). ees ee 1
Speakon ley e800 a. Ss Mieke ee til amie |
2-2. OPERATING LOCATION
As with any solid-state electronic equipment, the
place of use must be discriminated with the TS-600, in
order to avoid subjecting to extremes of ambient condi-
tions.
A well-ventilated, dry place, where the transceiver will
not be exposed to direct sunlight, should be selected. The
TS-600 has a heat sink in its rear panel; be sure to install
the transceiver so that there is a proper clearance at the rear
and bottom. For better heat dissipation, keep it away from
a wall. This precaution also applies when the transceiver is
operated on the companion's seat in a car.
: When you wish to use the transceiver in a car, you
may put it on the seat but sure to secure some heat dis-
sipating clearance under and behind it and to make proper
provisions for protecting it against shocks.
2-3. POWER SUPPLY CONNECTION
The TS-600 is designed to operated on AC 120/220V
or DC 13.8V. Switching between AC and DC is accomplish-
ed by replacing the power cord. The DC power cord is color
coded (red for ''+"' and black for ""—''). When connecting
power cord, be sure to observe the following points:
1. Turn off the power switch and set the standby switch
REC position.
2. When replacing power cord, disconnect it from the
AC socket (or battery). Care should be used to
prevent electrical shocks when connecting the AC
power cord.
Each power cord is equipped with a 4-P plug complete with
a stopper. When inserting the plug to the transceiver, be
sure to press down the stopper with your finger and
engage it into the latch on the transceiver side.
To pull the cord off the transceiver, push down the
stopper to disengage it from the latch and the give a pull
to the cord end. (See Fig. 1)
2-4. MICROPHONE
The microphone supplied with this transceiver is a
500-ohm impedance one designed specially for radio equip-
ment of this class. Any other microphone may be used
provided that its type and characteristic are suited to the
transceiver. The optimum impedance of a microphone is
anywhere between 500 and 600 ohms. For connection of
microphone, refer to Fig. 2.
Seen from the cord
Microphone
Fig. 2 Microphone connector Wiring
2-5. MIC HOOK
Attach a microphone hook to the case following the
instructions give in Fig. 3. The hook is furnished with the
equipment.
HOLE OF _
MIC HOOK CASE
SCREW () I
SCREWS
Fig. 3. Mounting of Microphone Hook