Advertisement
Quick Links
INSTALLATION MANUAL
PRODUCT: CONCEALED WINCH MOUNTING BRACKET
MODEL:
FORD RANGER (2015-)
PART NO:
2L.1801.2
CAUTION!
To reduce the risk of serious injury or damage, please read and understand all instructions and
procedures before attempting to install or use this product.
Safety glasses must be worn at all times during installation or maintenance of this product.
Ensure all mounting bolts are tensioned after 1000 kms and periodically there after.
www.rival4x4.com
Advertisement
Related Manuals for Rival 2L.1801.2
Summary of Contents for Rival 2L.1801.2
- Page 1 PRODUCT: CONCEALED WINCH MOUNTING BRACKET MODEL: FORD RANGER (2015-) PART NO: 2L.1801.2 CAUTION! To reduce the risk of serious injury or damage, please read and understand all instructions and procedures before attempting to install or use this product. Safety glasses must be worn at all times during installation or maintenance of this product.
- Page 2 12,5 kg SAFETY NOTICE * The RIVAL concealed winch mounting bracket is designed to compliment the use and design of the specified vehicle under conditions specified by the car manufacturer. * While driving the vehicle at any speed, collision with any other vehicle, animal or object must always be avoided.
- Page 3 TECHNICAL INFORMATION WINCH INSTALLATION A winch with a pull capacity of up to 11000lb (4989 kg) can be installed with the RIVAL concealed winch mounting bracket. It is not advisable to exceed this pulling capacity since damage, injury or death may occur where the 11000lb recommended capacity is exceeded.
- Page 4 1 pc. 4. Left right bracket........1 pc. 5. Insert nut М10........4 pc. 6. Bolt М10х30.......... 14 pc. 7. Nut М10..........10 pc. 8. Washer10..........24 pc. Installation manual 2L.1801.2 www.rival4x4.com Date: 12.08.2021 < Page 3 of 11 >...
- Page 5 * Keep all the fitting elements with you for further installation 4. Remove 4 screws out of lower lip of the bumper. * Keep all the fitting elements with you for further installation. Installation manual 2L.1801.2 www.rival4x4.com Date: 12.08.2021 < Page 4 of 11 >...
- Page 6 * Keep all the fitting elements with you for further installation. 6. Remove upper panel. 7. Remove 2 screws out of radiator grill. * Keep all the fitting elements with you for further installation. Installation manual 2L.1801.2 www.rival4x4.com Date: 12.08.2021 < Page 5 of 11 >...
- Page 7 9. Remove plastic plugs out of bumper. * Keep all the fitting elements with you for further installation. 10. Deinstall the bumper. Pull the bumper towards you holding the sides. Installation manual 2L.1801.2 www.rival4x4.com Date: 12.08.2021 < Page 6 of 11 >...
- Page 8 * Keep all the fitting elements with you for further installation. 13. Remove 4 bolts out of front bar. Remove the bar. * Keep all the fitting elements with you for further installation. Installation manual 2L.1801.2 www.rival4x4.com Date: 12.08.2021 < Page 7 of 11 >...
- Page 9 16. Mount inner left bracket (3) to the left side chassis. Fix it with bolts M10х30 (6), washers 8 to insert nuts (5). Mount bracket (4) same way on another side. DO NOT TIGHTEN YET. Installation manual 2L.1801.2 www.rival4x4.com Date: 12.08.2021 < Page 8 of 11 >...
- Page 10 18. Mount winch bracket (1) to the chassis. Fix it to brackets (2, 3, 4) by bolts М10х30 (6), nuts М10 (7) and washers (8). Tighten all nuts and bolts. Installation manual 2L.1801.2 www.rival4x4.com Date: 12.08.2021 < Page 9 of 11 >...
- Page 11 Инструкция по установке INSTALLATION PROCEDURE 19. Mark area for winch fairlead (not supplied with RIVAL bracket). Cut as marked. 20. Mount the winch and fairlead to the bracket using the bolts supplied with the fairlead. 21. Install front bumper and the grill to the vehicle.
- Page 12 Инструкция по установке INSTALLATION PROCEDURE Before operating a vehicle fitted with a RIVAL concealed winch mounting bracket: - make sure all fittings are tightened - connect the battery wiring which was previously disconnected - check all electrical wiring - check winch operation Installation manual 2L.1801.2...