DR-BT21G
TABLE OF CONTENTS
........................................................................... 2
2-1. Disassembly Flow ยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยท 3
2-2. Driver (R-CH) ยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยท 3
2-4. Main Board ยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยท 4
2-5. Driver (L-CH) ยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยท 5
2-7. Charger Board ยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยท 6
3-1. Block Diagram ยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยท 8
3-3. Schematic Diagram ยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยท 10
4-1. Housing (R) Section ยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยท 11
4-2. Housing (L) Section ยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยทยท 12
Notes on chip component replacement
โข Never reuse a disconnected chip component.
โข Notice that the minus side of a tantalum capacitor may be
damaged by heat.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Location and Function of Parts
2
........................................ 13
SECTION 1
GENERAL
Indicator (blue)
1
Indicates the communication
status of the unit.
2
Indicator (red)
Indicates the power status of
the unit.
3
Multi function button
Controls various call functions.
Press the button on the tactile
dots.
4
Jog switch
Controls various functions
when listening to music.
5
RESET button
Push this button when this unit
does not operate properly.
Pairing information is not
deleted by this operation.
Unleaded solder
Boards requiring use of unleaded solder are printed with the lead
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
โข Unleaded solder melts at a temperature about 40ยฐC higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to
be applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set
to about 350ยฐC.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
โข Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
โข Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder
may also be added to ordinary solder.
โข IC101 (CXN1450-2ABL) on MAIN board cannot be
replaced individually.
Replace it with "MAIN BOARD, COMPLETE".
6
VOL (volume) +*โ-
buttons
7
Neckband
8
(right) indication
9
Left unit
(left) indication
q;
qa
Ear pad
qs
Right unit
qd
POWER button
qf
Microphone
qg
DC IN 3 V jack
* This button has a tactile dot.
This section is extracted
from instruction manual.