Advertisement
A few simple tips to help ensure a fantastic frothing experience every time.
Fresher is Better
Using fresh milk delivers the richest, frothiest foam possible. Opened milk will still froth, but may lose effectiveness over time as the fats inside break down.
Milk Matters! Different types of milk produce different results. Depending on which milk you use, here's what you can expect:
Not All Brands Are the Same
Even individual brands of milk can froth differently, so experiment with different brands to see what works best.
INSTRUCTIONS
HOT AND COLD FROTHER: Use any fresh milk or dairy alternative, like oat, almond, or soy.
BREW OVER ICE: Brews by starting hotter to extract full flavor, then cooling down for less ice melt.
SHOT: Use any K-Cup® pod to brew a concentrated 2oz coffee shot.
FAST & FRESH-BREWED: Coffee made in minutes.
BACK-TO-BACK BREWING: Immediately brew a second cup; no need to wait for reheating.
TRAVEL MUG FRIENDLY: Accommodates travel mugs up to 7.25" tall.
SIMPLE BUTTON CONTROLS: Just insert any K-Cup® pod and use the button controls to brew a delicious cup.
MAINTENANCE ALERT: Reminds you to descale after every 500 brews.
NOTE: Regular descaling enhances the taste of your coffee and the longterm performance of your brewer.
COMPATIBLE WITH THE MY K-CUP® UNIVERSAL REUSABLE COFFEE FILTER: Brew your own ground coffee (sold separately).
AUTO OFF: Automatically turns your brewer off 5 minutes after the last brew for energy savings, but will be ready to brew as soon as it is powered on again.
HIGH ALTITUDE BREWING: While holding the brewer handle up, push down slowly on the K-Cup® pod in the pod holder until the bottom of the K-Cup® pod is punctured by the exit needle.
HIGH ALTITUDE: To ensure your coffee maker works properly at higher altitudes (5,000 feet), please enable the High Altitude Brewing Mode on your coffee maker.
High Altitude Mode will remain enabled until steps 1-2 are repeated and the 8oz light turns on to confirm that the High Altitude Brewing Mode is disabled.
Regular cleaning keeps your brewer running smoothly. Always be sure to turn off and unplug your brewer before cleaning.
Keep your Keurig® brewer looking its best by cleaning the exterior from time to time. Just clean with a damp, soapy, lint-free, nonabrasive cloth. Never immerse the brewer in water or other liquids.
The drip tray overflow should be emptied and cleaned occasionally. To remove, lift up off brewer base, keeping it level to avoid spilling. Rinse and clean with a damp, soapy, lint-free, nonabrasive cloth. Hand-wash only.
The water reservoir should be cleaned periodically by wiping the inside of the reservoir and underside of the lid with a damp, nonabrasive, lint-free cloth. Do not dry the inside of the water reservoir with a cloth, as lint may remain. Allow the reservoir to dry completely. Hand-wash only.
Clean immediately after each use and before first use.
To Clean:
NOTE: Frother is not dishwasher safe. Do not submerge frother in water. Only use nonabrasive cleaning materials to prevent damage to the inner surface of the frother.
To remove the K-Cup® pod holder from the brewer, lift the handle and grasp the top of the K-Cup® pod holder with one hand while pushing up on the bottom of the K-Cup® pod holder from underneath with the other until it releases. After cleaning, align the K-Cup® pod holder with the opening, using the two front ribs as a guide, and snap into place from the top.
There are sharp needles that puncture the K-Cup® pod above the K-Cup® pod holder and in the bottom of the K-Cup® pod holder. To avoid risk of injury, do not put your fingers in the K-Cup® pod holder.
NOTE: Always remove and dispose of the used K-Cup® pod after brewing.
Washing the funnel ensures a fresh beverage experience. The funnel should be washed regularly and can be removed from the K-Cup® pod holder by pulling on it until it pops off. To replace it, orient the snaps to the indent and just snap it back onto the K-Cup® pod holder.
Remove the pod holder assembly and detach the funnel. Locate the exit needle on the inside bottom of the K-Cup® pod holder. Insert a straightened paper clip into the exit needle to loosen any coffee grounds.
Lift the brewer handle and locate the entrance needle on the underside of the lid. To clean the holes in the needle, hold the brewer handle in the upward position; with your other hand, carefully insert a straightened paper clip into all the holes. Gently move it around to loosen any coffee grounds. Lower the handle completely and run a cleansing brew two times. Do not insert a K-Cup® pod.
For great-tasting coffee, keep your brewer running at peak performance by following the recommended maintenance schedule:
Frequency | Product | Benefit |
Weekly | Keurig® Rinse Pods | Weekly cleaning with Keurig® Rinse Pods helps reduce flavor carryover between brews |
Every two months | Keurig® Water Filters | Keep your water fresh and help remove impurities |
Every three months or when the Descale notification turns on* | Keurig® Descaling Solution Keurig® Descale Pouch** | Eliminate mineral buildup to preserve the longterm health of your coffee maker |
*To turn off Descale notification, follow the full descaling procedure as outlined in this guide.
**Please visit www.keurig.com/descale for instructions on using the Descale Pouch.
If the brewer has been in storage or hasn't been used in days, run a cleansing brew before brewing your beverage. Periodically hand-wash the water reservoir and lid and drip tray with warm, soapy water and rinse clean.
Parts are not dishwasher safe.
NOTE: Do not dry the inside of the water reservoir with a cloth, as lint may remain.
NOTE: The full descaling procedure must be completed to turn off the Descale light.
You will need: A large ceramic mug (10oz minimum), fresh water, Keurig® Descaling Solution, and access to a sink.
Do not use a paper cup. Ensure that there is no beverage pod in the K-Cup® pod holder. The descaling procedure takes approximately 20 minutes.
Pour the entire bottle of Keurig® Descaling Solution into the empty water reservoir. Then fill the empty bottle with water and pour into the water reservoir.
Do not insert a K-Cup® pod.
Place a large mug on the drip tray.
To activate Descale Mode, begin with the brewer plugged in and powered off, then press and hold the 8oz and 12oz buttons together for 3 seconds.
When flashing, press the 12oz button to start the descaling process. Once the brew is complete, pour the hot liquid into the sink. Continue to brew until the ADD WATER light illuminates.
Empty and rinse the water reservoir and refill to the MAX FILL line with fresh water. When flashing, press the 12oz button to start the rinsing process.
Once the brew is complete, pour the hot liquid into the sink.
Continue to brew until the Descale notification turns off.
The brewer has now exited Descale Mode and is ready for use!
NOTE: The cleaning action of Keurig® Descaling Solution may result in a "foam" dispensed from the brewer. This is natural, as the solution is reacting with the scale inside. For a brewer that is heavily scaled, the brewer may not fill properly after the descaler is added. If this occurs, you may see little to no output dispensed, followed by the sound of air blowing out. If this occurs:
The brewer should begin to function normally as the solution is rinsed out and the scale is removed. If problem persists, allow brewer to sit unplugged for at least 30 minutes before continuing with the rinse.
NOTE: Froth time will vary depending on the temperature of the milk.
Grounds may have gathered in the exit or entrance needles and can be cleaned using a straightened paper clip or similar tool.
For optimal enjoyment and to limit grounds in your cup during hot water brews or when transitioning from brewing a coffee pod to a non-coffee pod (e.g., tea or cocoa), clean the exit and entrance needles per the instructions provided and perform two cleansing brews.
Water quality varies greatly. If you notice an undesirable taste in your beverage (such as chlorine or mineral tastes), we recommend using bottled or filtered water. Do not use distilled water.
Beyond these recommended cleaning and maintenance procedures, this brewer is not user serviceable. For service, please refer to the Warranty section of this guide.
Empty the water reservoir before storing or transporting and take care to ensure that you store your brewer in a safe and frost-free environment. When you prepare to use it after storage, we recommend rinsing the water reservoir with fresh water and descaling the brewer as detailed in the Descaling Procedure section.
If you plan to move your brewer to a different location, turn the brewer off, unplug it, and empty the water reservoir. If your brewer has been in an environment below freezing, please be sure to let it warm to room temperature for at least 2 hours before using.
Have Questions?
We're here to help.
Visit support.keurig.com for step-by-step videos on cleaning, descaling, and more.
Still Need Help?
Give us a call at 1-866-901-BREW (2739).
For replacement parts, please visit www.keurig.com.
Start your Keurig® experience by finding your favorite pods and registering your brewer
keurig.com/hello
Have questions? We're here to help. Visit support.keurig.com for troubleshooting videos, maintenance recommendations, and the full Use & Care Guide.
Still need help? Give us a call at 1-866-901-BREW (2739).
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download Keurig K-Café Barista Bar - Single Serve Coffee Maker Manual
Advertisement
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the K-Café Barista Bar that isn't answered in the manual? Leave your question here.