Related Manuals for Juniper JOT Desk BL-4
Summary of Contents for Juniper JOT Desk BL-4
- Page 1 BL-4 JOT Desk 120-Degree Workstation Includes Add-Ons: A1 | A2 | A3 General Installation Guide...
-
Page 3: Table Of Contents
Edition Code :: Pod of 3 .................... 1 BL-3 :: Pod of 6 ..................13 BL-3 Add-ons :: Laminate Surface-Height End Panels......21 :: Laminate Divider-Height End Panels ......25 :: Steel Inset End Panels ............29... -
Page 4: Pod Of 3
Pod of 3 Overview JOT 120-Degree Workstation All parts listed are for a Pod of 3; additional parts will be needed for additional Pods. - Page 5 Parts List Code Qty. Description GB120v2 Main Surface Long Beam Lock Plate BLPB2/ BLBB3 Cap Screw Locking Screw and Lever 48” End Leg BL48 Wood Screws 120-Degree Leg w/ Triangular Box KIT-120 Bolts Leg-Mount Cable Tray Hangers BCTLM** (Set of 2) CTXNL** Leg-Mount Cable Tray BTEC or...
- Page 6 1 | Assemble Post Legs (x3) Place triangle box on post leg and secure with 4 bolts. Attach corner protector on corner that will be facing toward user when desk is in use. 2 | Connect End Legs, Post Legs and Beams Insert beam tabs into leg brackets.
- Page 7 3 | Bolt Down Beam-to-Leg Lock Plate Note: Beam lock plates will not fit if there is a gap between beam and leg. 4 | Measure and Adjust Beam Width Measure from end leg to end leg until you find the approximate width of work surfaces. Insert screw through overlapping beam slots and into locking screw and lever.
- Page 8 5 | Attach Cable Tray Hangers and End Caps Align slots on cable tray and secure with 2 bolts from bottom. These hangers will mount to workstation. Insert Beam Grommet Covers. NOTE: End Caps (BTEC) are optional, follow the same install process with or without end caps.
- Page 9 7 | Leg Mount Cable Tray Insert tabs of connector bracket into triangle post leg slots, then use 2 screws to connect cable tray hanger to bracket. Secure other end of tray directly to end leg using 2 screws. Tighten beam lock.
- Page 10 9 | Surface Installation Measure from inner surface of leg bracket to outer edge of surface. Option 1: If installing dividers or monitor arms, leave 1 ” space between surfaces, full width should be 21 ” . Option 2: If not installing dividers or monitor arms, leave no space between surfaces, full width should be 21 ”...
- Page 11 10 | Secure First Surface Place surface on top of frame. Align outer side of surface flush and parallel with outer side of end leg. Insert wood screws into leg brackets and secure to underside of surface. 11 | Place and Secure First Divider NOTE: Skip step if not installing dividers.
- Page 12 12 | Secure Second Surface Place second surface on top of frame. Align outer side of surface flush and parallel with outer side of end leg. Insert wood screws into leg brackets and secure to underside of surface. 13 | Place and Secure Second Divider NOTE: Skip step if not installing dividers.
- Page 13 14 | Place and Secure Third Divider NOTE: Skip step if not installing dividers. Clamp bracket to surface's side edge and tighten vertical bolt against surface to secure bracket. Repeat for all brackets. Lower screen into brackets and tighten horizontal bolt to clamp brackets onto screens. 15 | Secure Support Bars Place third surface on top of frame.
- Page 14 16 | Tighten Beam Locks...
-
Page 16: Pod Of 6
Pod of 6 Overview JOT 120-Degree Workstation All parts listed are for a Pod of 6; additional parts will be needed for additional Pods. - Page 17 Parts List Code Qty. Description GB120v2 Main Surface Long Beam Lock Plate BLPB2/ BLBB3 Cap Screw Locking Screw and Lever 48” End Leg BL48 Wood Screws 120-Degree Leg w/ Triangular Box KIT-120 Bolts 48” Intermediate Leg BL48INT Cap Screw...
- Page 18 1 | Assemble Post Legs (x6) Place triangle box on post leg and secure with 4 bolts. Attach corner protector on corner that will be facing toward user when desk is in use. 2 | Assemble Intermediate Leg Align bracket with leg holes and bolt in place. Connect 4 brackets to leg. Insert 2 bolts per bracket to secure in place.
- Page 19 3 | Connect End Legs, Intermediate Leg, Post Legs and Beams Insert beam tabs into leg brackets. Guide beam tabs into bracket holes, ensuring that there is not a gap between the beam and legs. Using a rubber mallet, hammer beam to lock in place.
- Page 20 4 | Bolt Down Beam-to-Leg Lock Plate Note: Beam lock plates will not fit if there is a gap between beam and leg.
- Page 21 5 | Measure Approximate Leg Spacing NOTE: Leg spacing will be adjusted as surfaces are positioned. Measure from end leg to end leg until you find the approximate width of work surfaces. Insert screw through overlapping beam slots and into locking screw and lever. Slightly tighten screw.
- Page 22 6 | Surface Installation Measure from inner surface of leg bracket to outer edge of surface. Option 1: If installing dividers or monitor arms, leave 1 ” space between surfaces, full width should be 21 ” . NOTE: See pages 8-10 if installing dividers. Option 2: If not installing dividers or monitor arms, leave no space between surfaces, full width should be 21 ”...
- Page 23 7 | Tighten Beam Locks...
-
Page 24: A1: Laminate Surface-Height End Panels
A1: Laminate Surface-Height End Panels Overview JOT 120-Degree Workstation All parts listed are for single side of workstation; additional parts will be needed for additional end panels.. - Page 25 Parts List Code Qty. Description GBEPLH## or Laminate Surface-Height End Panel WABEPIS.# End Panel T-Bracket LEPBL1 Self-Tapping Screws Wood Screws...
- Page 26 1 | Secure Bracket to End Legs Attach 4 brackets to each end leg using self-tapping screws. Front of bracket will align flush with outside edge of leg. Align Flush...
- Page 27 2 | Attach End Panel Slide end panels into place and adjust until flush with bracket. Use wood screws to secure panel to each bracket.
-
Page 28: A2: Laminate Divider-Height End Panels
A2: Laminate Divider-Height End Panels Overview JOT 120-Degree Workstation All parts listed are for a single panel; additional parts will be needed for additional panels. - Page 29 Parts List Code Qty. Description GBEPSS## or Laminate Divider-Height End Panel WABEPDH.# End Panel T-Bracket LEPBL1 Self-Tapping Screws Wood Screws...
- Page 30 1 | Secure Bracket to End Legs Attach 4 brackets to each end leg using self-tapping screws. Front of bracket will align flush with outside edge of leg. Align Flush...
- Page 31 2 | Attach End Panel Slide end panels into place and adjust until flush with bracket. Use wood screws to secure panel to each bracket.
-
Page 32: A3: Steel Inset End Panels
A3: Steel Inset End Panels Overview JOT 120-Degree Workstation All parts listed are for a steel inset end panel; additional parts will be needed for additional steel inset end panels. - Page 33 Parts List Code Qty. Description Steel Inset End Panel BEP60 or BCEP60 Self-Tapping Screws...
- Page 34 1 | Secure Panels to End Legs Slide the end panel into place and adjust until either flush with outside of leg or slightly recessed. Align Flush Slightly Recessed...
- Page 35 2 | Attach End Panel Use 4-6 self-tapping screws to secure panel to each leg.
- Page 36 1-866-999-0955 | hello@juniperoffice.com | juniperoffice.com © 2023 Juniper Office | Version 23.0.0...