Advertisement
PANEL FACILITIES
: Normal position
(When neither LASERDISC
nor VCR signal is input.)
If "CABLE"
is automatically
selected
even
though
"
TAPE/AUX"
signal is being played , set to this position 7
L" to select "TAPE/AUX."
H:
(When neither LASERDISC nor VCR signal is input.)
if AUTO INPUT selector remains at "TAPE/AUX" even
though
TAPE/AUX
finishes
its playback,
set
to this
position "H" to select "CABLE."
7 TAPE/AUX VOLUME
control
Controls
the input sound
level
of devices
connected
to the
TAPE/AUX input jacks. This control is normally centered but should
be adjust for LASERDISC.
8) TAPE/AUX MODE switch
This switch is used to select audio modes (MONO/STEREO) of
components connected to the TAPE/AUX input jacks, Connect 4
component with monophonic audio output either to "'L'' or RY
AUDIO INPUT jack and set this switch to "MONO."
@ VISUAL
INPUT jacks
WM 1 LASERDISC
Connect to the VIDEO OUT jack of the LD player.
9.2 VCRICAMERA
Connect to the VIDEO OUTPUT jack of the VCR or TV camera.
rs
1 VISUAL OUTPUT jacks
m1-3
Jacks
for.connection
to the VIDEO
INPUT
jacks of TV
monitors (maximum three monitors).
Wi VCR/CAMERA
ONLY
Signats input to the "VCR/CAMERA" VISUAL INPUT jack
of the SA-V210 will always be output. By connecting to a
TV monitor, you can monitor a VCR or TV camera.
{? SPEAKERS terminals
Two
speaker
systems
(A and
B) can
be connected.
For
details, refer to "CONNECTIONS" on page 3.
* Always connect the plus (+) and minus (—) wires of the
speakers to the speaker terminals of the same polarity. A
polarity error can cause unnatural sound.
13 MIC input jacks 1,2,3
Microphones cannot be connected directly to the SA-V210.
When
placing
the
SA-V210
into a rack
with
MIC
cords,
connect the MIC cords of the rack.
When using microphones
with key control remote switch connected to MIC
4 and 2,
connect the control cords to the KEY
CONTROLLER jacks.
NOTE:
14 AUDIO OUTPUT MONITOR
L + R jack
The
L and
R audio
signals input to the audio
input jacks
49 AUDIO OUTPUT jacks
These jacks are used to output the L and R audio signals to the audio
input jacks (LASERDISC, VCR, CABLE, TAPE/AUX).of this unit.
16 HOWLING
CUT switch
In case of howling, set this switch to "ON."
d? TAPE REC jacks
Connect to the REC
(INPUT] jacks of a cassette deck.
Mic
mixing recording will be possible, because signals. processed
with microphone mixing are output.
When "TAPE/AUX" or "CABLE" has been selected, no sound
can be heard.
48 KEY CONTROLLER AUTO RETURN
switch
ON —
When
a song
is finished,
the
key
controller
will
automatically return to the standard key (4).
GFF —
The key will only change by key control operation.
49: KEY CONTROLLER
REMOTE
CONTROL
jack
commander.)
be remote-controlied.
40 GND (Ground) terminal
Always
ground this unit to prevent electrical shock
and to
avoid generating interference or noise in other equipment.
@) Power cord
FRONT PANEL
1) POWER switch (HZ OFF,
a ON)
'2; MAIN VOLUME control
'3; MUSIC control
Controls
the
volume
of
equipments
connected
to
the
LASERDISC,
VCR,
CABLE and TAPE/AUX
jacks on the rear
panel. Normally, keep the MAIN VOLUME
control near the 5
~ 7 position and use the MUSIC control to adjust the volume
of the music source.
4) BALANCE control
Adjusts the balance
between
the sound
from the left and
right.
)» MUSIC. TONE controls
These contro! the tones (BASS/TREBLE) of the music source.
"€ MIC ECHO control
5
<ARC1172>
En
Advertisement
