Bosch 0 601 9K3 205 Original Instructions Manual page 15

Apply pressure only in direct line with the bit and do
u
not apply excessive pressure.Bits can bend causing
breakage or loss of control, resulting in personal injury.
Additional safety warnings
Switch the power tool off immediately if the applica-
u
tion tool becomes blocked. Be prepared for high
torque reactions which cause kickback. The applica-
tion tool becomes blocked when it becomes jammed in
the workpiece or when the power tool becomes over-
loaded.
Hold the power tool securely. When tightening and
u
loosening screws be prepared for temporarily high torque
reactions.
Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
Use suitable detectors to determine if there are hid-
u
den supply lines or contact the local utility company
for assistance. Contact with electric cables can cause
fire and electric shock. Damaging gas lines can lead to ex-
plosion. Breaking water pipes causes property damage.
Always wait until the power tool has come to a com-
u
plete stop before placing it down. The application tool
can jam and cause you to lose control of the power tool.
In case of damage and improper use of the battery, va-
u
pours may be emitted. The battery can set alight or ex-
plode. Ensure the area is well ventilated and seek medical
attention should you experience any adverse effects. The
vapours may irritate the respiratory system.
Do not open the battery. There is a risk of short-circuit-
u
ing.
The battery can be damaged by pointed objects such
u
as nails or screwdrivers or by force applied externally.
An internal short circuit may occur, causing the battery to
burn, smoke, explode or overheat.
Only use the battery with products from the manufac-
u
turer. This is the only way in which you can protect the
battery against dangerous overload.
Technical data
Cordless Drill/Driver
Article number
Rated voltage
A)
No-load speed
– First gear
– Second gear
A)
Impact rate
A)
Max. torque (soft)
A)
Max. torque (hard)
Bosch Power Tools
Protect the battery against heat, e.g. against
continuous intense sunlight, fire, dirt, water
and moisture. There is a risk of explosion and
short-circuiting.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended use
The power tool is intended for driving and loosening screws
and for drilling in wood, metal, ceramic and plastic. The GSB
cordless combi drill is also designed for impact drilling in
brick, masonry and stone.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Tool holder
(2) Keyless chuck
(3) Torque presetting ring
(4) Operating mode presetting ring
(GSB 18V-45)
(5) Gear selector switch
(6) Belt clip
a)
(7) Rechargeable battery
(8) Battery release button
(9) Worklight (LED)
(10) Rotational direction switch
(11) On/off switch
(12) Handle (insulated gripping surface)
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
GSR 18V-45
3 601 JK3 2..
V= 18
-1
min 0–500
-1
min 0–1,900
-1
min
Nm 21
Nm 45
English | 15
a)
GSB 18V-45
3 601 JK3 3..
18
0–500
0–1,900
– 0–27,000
21
45
1 609 92A 7KU | (23.08.2022)