Table of Contents
Advertisement
Yo lj(om ©) ey-1ce}l(o)e
Initial System Start-Up
immediately after installation, after the
vehicle's battery has been disconnected, or
after the addition of an optional CD Shuttle, it
is necessary to reset the system. This is
done by first setting the volume level to its
minimum. Next, press and hold the DISC
button for at least 3 seconds.
Turning Power
On and Off
Press the PWR button to tum on the unit.
Note:
The unit can be turned on by pressing
any other button except the eject &,
44 and P > buttons.
The volume jevel gradually increases to the
previous level you were listening to before
the unit was tumed off.
Press the PWR button again to tum off the
unit.
Adjusting
Volume/Bass/Treble/
Balance/Fader
Press the MODE button repeatedly to
choose the desired mode.
Note:
{f the v or ~ button is not pressed in 5
seconds after selecting the BAS,
TRE, BAL and FAD modes, the unit
automatically sets in the VOL mode.
Press the v and ~ buttons until the desired
sound is obtained in each mode.
Note:
The settings of the Bass and Treble
will be individually memorized tor
each source (radio and tape) until the
setting is changed.
Turning Loudness
On/Off
Press and hold the LOUD button for at least
2 seconds to activate or deactivate the
loudness made. The display shows "LD"
when the loudness mode is activated.
TDM-7529T/F
TDM-7526T/W/F
| Xelol (om @)ey=)celife)a)
Manual Tuning
Press the BAND button repeatedly until the
desired radio band is dispiayed.
(rom-75297/ | crom-7526w)
7529F/75267/ |
7526F)
Press the TUNE button repeatedly until
"MAnu' is displayed.
Note:
The initial mode is DX-SEEK.
Press the DN or UP button to move down-
ward or upward one step respectively until
the desired station frequency is displayed.
Note:
The ST indicator appears on the
display when a Stereo FM station is
tuned in. if the stereo FM signal
becomes weak, the ST indicator
disappears and the unit automatically
switches the mode from stereo to
monaural to reduce the noise. When
the signal becomes strong enough,
the unit automatically switches back
to the stereo mode.
Automatic Seek Tuning
Press the BAND button repeatedly until the
Fi
desired radio band is displayed.
+
[Fa"
+
Caw
(TOM-75297/ | crom-7s26w)
7S29F/75267/ |
7526F)
Press the TUNE button to illuminate the DX
and SEEK indicators in the display. The
SEEK indicator illuminates only for a few
seconds. With the DX mode activated, both
strong and weak stations will be tuned in the
Auto-Seek operation.
Press again to return to the local mode. The
DX indicator goes off and the SEEK indicator
illuminates for a few seconds, and only
strong radio stations will be tuned.
Press the DN or UP button to automatically
seek a station downward or upward
respectively.
When the unit finds a station, the unit stops
at that station.
Press the same button again to seek next
station.
TDM-7529T/F
TDM-7526T/W/F
{ole [foe @jey-1relifela
Manual Storing of
Station Presets
. Select the radio band and tune ina
desired radio station you wish to store in
the preset memory.
. Press and hold any one of the preset
buttons (1 through 6) for at least 2
seconds until the station frequency on the
display blinks.
. Press the preset button into which you
wish to store the station while the fre-
quency display is blinking (within 5
seconds).
The display changes from blinking to
steady lighting indicating that the station
has been memorized. The display shows
the band, preset No. with a triangle (=)
and station frequency memorized.
. Repeat the procedure to store up to 5
other stations onto the same band.
To use this procedure for other bands,
simply select the band desired and repeat
the procedure.
A total of 24 stations can be stored in the
preset memory {6 stations for each band).
Note:
{f a preset memory has already been
set in the same preset tocation, it will
be cleared and the new station will be
memorized.
Automatic Memory of
Station Presets
Press the BAND button repeatedly until the
desired radio band is displayed.
crom-752971 | (TDM-7526W)
7529F/7526T/ |
7526F)
Press and hold the A. MEMO button for at
least 2 seconds. The frequency on the
display continues to change while the
automatic memory is in process.
The tuner will automatically seek and store 6
Strong stations in the selected band in order
of signal strength.
When the automatic memory has been
completed, the tuner goes to the station
stored in the preset location No. 1.
Note:
If no stations are stored, the tuner will
return to the original station you were
listening to before the auto memory
procedure began.
When a preset station is selected, a
triangle with 4 horizontal stripes will
be displayed next to the preset
number.
Radio Operation
Recalling Preset Sta-
Press the BAND button repeatedly until the
desired band is displayed.
Fi
¥
[Fz
+
Caw
(TDM-7529T/ | (TDM-7526W)
7529F/7526T/ |
Press the station preset button that has your
desired radio station in memory. The display
shows the band, preset number with a
triangle and frequency of the station
selected.
Storing into Direct
Access Preset
(D.A.P.) Band
A combination of radio stations in any bands
(up to 6 stations) can be preset manually
onto the D.A.P. band,
Press the D.A.P. button until the D.A.P.
indicator appears.
DAPMLX,
Press the BAND button to select the desired
band. The display shows the selected band.
To memorize the stations onto the D.A.P.
band, follow the steps for the Automatic or
(TDM-7529T/
(TOM-7529F/
Manual Storing of Station Presets section
7526T)
7526F/7526W)
above,
Note:
The function can be used together
| =
with the Automatic Memory Preset if
you want to store stations in the
same radio band.
Advertisement
Table of Contents
