Table of Contents
Advertisement
At trouble
The watch displays an
Misalignment
incorrect time hour unit,
of the time
even though it displays the
The time zone selection is incorrect.
and hand
precise time of minutes
positions
and seconds.
The date is out of the preliminary
The reception results are
position.
successful and the precise
Misalignment
This happens when the date is out of
time is displayed, but the
of the date
the preliminary position as a result of
date is not correctly
influence of various external sources or
displayed.
after the built-in IC is reset.
The reception result
The preliminary position of the day of
display confirms
week is out of alignment.
Misalignment
successful reception, and
This problem occurs when the
of the day
the correct time is
preliminary position of the day of week
displayed, but the wrong
is out of alignment due to external
day is displayed.
influence and system reset etc.
7
The sub dial is set to the
Wrong
time shown by the main
display of the
The sub dial displays the wrong time. Refer to" How to set the sub dial".
watch, but the sub dial
sub dial
displays the wrong time.
92
EN
In case of an abnormal movement
In the case that the watch moves abnormally or that the watch does not move at one-second intervals even
after fully charging the battery, then it can be returned to normal operation using the following operation.
■ Reset the system
1
Pull out the crown to the second click.
The seconds hand moves to the 0-second position
and stops.
* When the crown is a screw lock type, unlock it.
→ P.14
7
94
EN
Possible causes
Solutions
Check the selected time zone and set it
to the area where the watch is used.
Set the date to the preliminary position
"1" (the 1st).
Check if the day is set to the correct
preliminary position "S" (Sunday).
Pull out the
0 1 2
crown to the
second click
Reference
At trouble
The crown or button
P.31
Operation
cannot be operated.
P.82
You get lost in the middle
Operation
of the operation.
P.82
Blur on the dial glass
Others
persists.
* For the solution of troubles other than the above, consult the retailer from whom the watch was purchased.
P.38
2
Keep pressing down the Button A and B
at the same time for 3 seconds, and then
release them.
After releasing the button, approximately 5 seconds
later the seconds hand moves, and stops at the
0-second position.
Then the hour and minute hands will start to move
and stop pointing to 12 o'clock 0 minutes.
* First, press the Button B, and subsequently press the
Button A while keeping holding down the Button B so
as to press both of them successfully.
* The button cannot be operated until all the hands stop.
3
When all the hands stop pointing to 12 o'clock 0 minutes and 0 seconds, push
the crown back.
The seconds hand starts moving from 12 o'clock 0 minutes and 0 seconds.
* After the built-in IC is reset, the watch is set to the time zone LON.
After completion of a system reset, perform the following operations.
• "Setting the preliminary position of the date, day hand, hour and minute hands" → P.82
• "How to select the time zone (How to display the local time around the world)" → P.31
• "How to conduct manual reception (Receive a radio signal manually)" → P.70
* When the crown is a screw lock type, lock it. → P.14
Possible causes
Solutions
The stored electric power is running
Sufficiently charge the watch until it
short.
starts moving at one-second intervals.
Hands and date are moving right after
Wait without doing anything.
a setting is carried out by the crown or
After the date stops, the crown and
button operation.
button can be operated.
Return to the status before the start of
the operation, and try the operation
again.
If the crown is pulled out, push it in.
-----------
If the crown is not pulled out, then pull it
out and push it in again.
This will return to one-second interval
movement for a maximum of 9 minutes.
After this, try the operation again.
A small amount of water has got inside
Contact the retailer from whom the
the watch due to deterioration of the
watch was purchased.
gasket, etc.
Reference
P.40
-
-
-
7
93
EN
Button A
Press for
3 seconds
Button B
Press for
3 seconds
7
95
EN
Advertisement
Table of Contents
