Troubleshooting - Sony XAV-AX210 Owner's Record

("AVC VIDEO") AND/OR THE VC-1 STANDARD ("VC-1
VIDEO") THAT WAS ENCODED BY A CONSUMER
ENGAGED IN A PERSONAL AND NONCOMMERCIAL
ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO
PROVIDER LICENSED TO PROVIDE AVC VIDEO AND/
OR VC-1 VIDEO. NO LICENSE IS GRANTED OR SHALL
BE IMPLIED FOR ANY OTHER USE. ADDITIONAL
INFORMATION MAY BE OBTAINED FROM MPEG LA,
L.L.C. SEE HTTP://WWW.MPEGLA.COM
All other trademarks are trademarks of their
respective owners.

Troubleshooting

The following checklist will help you remedy
problems you may encounter with your unit.
Before going through the checklist below, check
the connection and operating procedures.
For details on using the fuse and removing the unit
from the dashboard, see "Connection/Installation"
(page 31).
If the problem is not solved, visit the support site on
the back cover.
General
No power is being supplied to the unit.
 Check the fuse.
 The connection is not correct.
– Connect the yellow and red power supply
leads.
There is no beep sound.
 An optional power amplifier is connected and
you are not using the built-in amplifier.
The contents of the memory have been erased.
 The power supply lead or battery has been
disconnected or it is not connected properly.
The fuse has blown.
The unit makes noise when the position of the
ignition is switched.
 The leads are not matched correctly with the car's
accessory power connector.
The display disappears from/does not appear on
the monitor.
 The dimmer is set to [ON] (page 17).
 The monitor off function is activated (page 6, 7).
– Touch anywhere on the display to turn the
display back on.
The display does not respond to your touch
correctly.
 Touch one part of the display at a time. If two or
more parts are touched simultaneously, the
display will not operate correctly.
 Calibrate the touch panel of the display (page 18).
 Touch the pressure sensitive panel firmly.
Menu items cannot be selected.
 Unavailable menu items are displayed in gray.
The operation buttons do not function.
 Press the reset button (page 5).
Radio reception
The stations cannot be received.
The sound is hampered by noise.
 The connection is not correct.
– Connect the REM OUT lead (blue/white striped)
or accessory power supply lead (red) to the
power supply lead of a car's antenna (aerial)
booster (only when your car has built-in radio
antenna (aerial) in the rear/side glass).
– Check the connection of the car antenna
(aerial).
– If the auto antenna (aerial) will not extend,
check the connection of the power antenna
(aerial) control lead.
Preset tuning is not possible.
 The broadcast signal is too weak.
RDS
PTY displays [PTY not found.].
 The current station is not a RDS station.
 RDS data has not been received.
 The station does not specify the program type.
Picture
There is no picture/picture noise occurs.
 A connection has not been made correctly.
 Check the connection between this unit and
other equipment and set the input selector of the
equipment to the source corresponding to this
unit.
 The disc is defective or dirty.
 Installation is not correct.
– Install the unit at an angle of less than 45° in a
sturdy part of the car.
 The parking cord (light green) is not connected to
the parking brake switch cord, or the parking
brake is not applied.
The picture does not fit in the screen.
 The aspect ratio is fixed on the playback source.
There is no picture/picture noise occurs in the
rear monitor.
 The color system setting is incorrect.
– Set the color system to [PAL] or [NTSC]
according to the connected monitor (page 19).
 A picture from the camera is displayed on this
unit.
– No picture appears in the rear monitor if a
picture from the camera is displayed on this
unit.
25
GB