Table of Contents
Advertisement
CERO ites
Operation to reset
puter and return it to normal condition.
Remote control operation is not possible.
Amplifier
Sound
is not output.
The STANDBY indicator blinks and sound
is not output.
Sound
is not
output
from
one
of the
speakers.
The microcomputer may fal! into malfunction {impossibility to
operate, erroneous display, etc.) when the power cord is un-
plugged while power is ON or due to an external factor. In this
case, execute the following procedure to reset the microcom-
XR-V6OEC (Ent
@ For U.S.A. and Canada:
i
Unpiug the power
cord from the power
socket and, while
holding the POWER key depressed, piug the power cord into
the socket again.
e For other countries:
While holding the REMOTE POWER key depressed, press the
MAIN POWER key to ON.
a
@Please note that resetting the microcomputer
clears the contents
stored in and returns to the condition when it teft the factory
# Batteries are exhausted
@ The remote control unit is too far away from
the marn system, controlling angle is too
iatge, or there is an obstacle in between
@ The audio cords and system contro! cords
are not connected properly
@ The source component to be operated does
not contain the tapeis) or CD
@ An attempt is made to play a tape which is
being recorded :n the cassette deck
@ The speaker cords are disconnected
@ The VOLUME is set to the minimum position
e@ MUTE is ON
@ The SPEAKERS keys are set to OFF
e@ The TAPE 2 (MONI.} key ts set to ON
@ Replace with new batteries
e Operate the emote
contro: unt within
the controllable range
= 12,
e@ Connect
properly reterring tc
"System
connection"
8.
@ Place the tape(s) or CD in the source com-
ponent to be piayed
e@ Wait unt! the recording is comp.eted
@ Connect them properly referring to
Sys-
tem connection".
- 8.
aN
3
@ Agjust the volume to a proper level
&
@ Press the MUTE key to OFF
-44
@ Set the SPEAKERS
keys to ON
wl 3.
e Set the TAPE
2 (MONI.} key to OFF
@ Speaker cords are snort-circuited
@ The speaker cord is disconnected
@ The BALANCE control is set 10 an extreme gosition
@ Turn the cower off, efirmnate the snor-circurt-
ing, then turn on the power again
- 8.
@ Connect it properly referring to "System
connection"
@ Adjust the Left/Right balance
Be
i
t
Sound is not output from the Surround
,
rear speaker
and/or
center speaker,
or
their sound is very smail.
A hum
noise
is generated
when
the
PHONO
input is selected.
Tuner
Radio stations cannot be received.
eThe
-ear-smeaker
cords
and/or
speake' co-d are drsconnected
@ The Surround play mode has not been engaged
e The REAR VOL. and/or CENTER VOL. con-
trols are Set to the minimum
level.
center
t
i @ Connect them properly referring to
"Sys-
tem connection"
8.
e@ Set the presence
mode
-
21
@ Adjust the REAR VOL and CENTER
VOL.
cantrots
@ The audio cord from the turntable is not in-
serted securely into the PHONO Jacks
@ The turntable is not grounded.
@ No antenna 's connected.
@ The broadcast band is not set property
@ The frequency of the desired station 1s not tuned
@ Insert the audio cord plugs secure nto
the PHONO jacks.
~&
e@ Connect
the grounding
wire
to the GND
term:nal on the rear ganel
e Connect
an
antenna
bate
@ Ser the broadcast band properly
xe
@ Tune tne frequency of the desireo Station =.17,
+
Interference.
A station which was preset cannot be re-
|
ceived by pressing the corresponding nu-
|
meric key.
i
be Se
ee
€ iJ
@ Noise due to ignition noise of an automobiie
@ Noise cue to an snfluence from an electric aogliance
e Noise due to a nearby TV set
@ The preset station belongs to a frequency
that cannot be received.
@ The preset
memory
was
cleared because
the power
cord
had been unplugged
for a
long period of time
@ Instali the outdoor antenna apart from tne 'aad
@ Turn off the power of the aopance
@ Install the system more apart from the "V set
@ Preset
a Staton
with
a receivable
*"
quency
*@ Preset the station again
Do nat use contact cleaners because
It could cause a malfunction
Be speciatly careful agains1 contact cleaners containing oli, for
tmey may Geform the paste components
Advertisement
Table of Contents
