Table of Contents
Advertisement
Quick Links
Visit website for
available languages of
this document.
DESCRIPTION
1
2
3
4
5
6
1.
2.
3.
4.
5.
6.
75.0050.01 LZR-FLATSCAN W 20230908
cover
LED
main connector
angle adjustment screw
mounting bracket
power cable
LZR-FLATSCAN W
SAFETY SENSOR FOR AUTOMATED WINDOWS
7.
lock screw
8.
laser head
9.
laser window
10.
laser window protection cap
11.
positioning tabs
12.
mounting base
(US version)
7
8
9
10
11
12
Page 1 of 12
Advertisement
Table of Contents
Related Manuals for BEA LZR-FLATSCAN W
Summary of Contents for BEA LZR-FLATSCAN W
- Page 1 (US version) this document. DESCRIPTION cover lock screw laser head main connector laser window angle adjustment screw laser window protection cap mounting bracket positioning tabs power cable mounting base 75.0050.01 LZR-FLATSCAN W 20230908 Page 1 of 12...
-
Page 2: Technical Specifications
All values measured in specific conditions. LED SIGNAL 1. Laser head initialization Output relay 1 activated (opening) 2. Output relay 2 activated (safety) 1. Calculation in progress Errors Define detection zone 2. Exit the zone and wait Page 2 of 12 75.0050.01 LZR-FLATSCAN W 20230908... -
Page 3: Installation Tips
75.0050.01 LZR-FLATSCAN W 20230908 Page 3 of 12... -
Page 4: How To Use The Remote Control
Enter the existing code ADJUSTING ONE OR MORE PARAMETERS CHECKING A VALUE x = number of flashes = value of the parameter = field width: 2.35 m RESTORING TO FACTORY VALUES full reset partial reset Page 4 of 12 75.0050.01 LZR-FLATSCAN W 20230908... - Page 5 (2). cover comes loose. When closing, be sure to secure the cover to avoid vibrations. MOUNTING NICHE MOUNTING NICHE MOUNTING SURFACE MOUNTING TOP MOUNT SIDE MOUNT 75.0050.01 LZR-FLATSCAN W 20230908 Page 5 of 12...
- Page 6 3. If TEST is not used, apply 12 – 24 VDC to TEST wires (red and blue) to bypass. ADJUSTING CURTAIN ANGLE If necessary, adjust the tilt angle of the laser curtain by turning the tilt angle adjustment screw. Page 6 of 12 75.0050.01 LZR-FLATSCAN W 20230908...
-
Page 7: Dip Switch Settings
Position yourself in front of the detection field and strech out your arm in the bottom corner opposite to the sensor in order to define the limit of the detection zone. The LED flashes red while calculating the detection zone. Once the LED is off, the teach-in is complete. 75.0050.01 LZR-FLATSCAN W 20230908 Page 7 of 12... - Page 8 Both of these options will remove ALL established virtual push buttons. You will have to perform new teach-ins for any that you wish to remain for your application. Launch a new teach-in each time the sensor position is changed or objects are added to or changed in the detection zone. Page 8 of 12 75.0050.01 LZR-FLATSCAN W 20230908...
- Page 9 ANALYSIS IS OFF 2 cm 4 cm 6 cm 8 cm 10 cm 12 cm 14 cm 16 cm 18 cm measured in specific conditions and dependant on application and installation FACTORY VALUES 75.0050.01 LZR-FLATSCAN W 20230908 Page 9 of 12...
-
Page 10: Output Configuration
To enter service mode, press the red button for at least 3 seconds. The LED will be OFF when the sensor is in service mode. To exit service mode, press again for at least 3 seconds. Service mode will automatically deactivate when a teach-in is launched. Page 10 of 12 75.0050.01 LZR-FLATSCAN W 20230908... -
Page 11: Troubleshooting
The ORANGE LED flashes 5 Teach-in error are fulfilled (see page 8) and launch a new x every 3 seconds. teach-in. Adjust the tilt angle of the laser curtain and launch a new teach-in. 75.0050.01 LZR-FLATSCAN W 20230908 Page 11 of 12... - Page 12 BEA, INC. INSTALLATION/SERVICE COMPLIANCE EXPECTATIONS The installation is provided by CUSTOMER or its affi liates. BEA is not affi liated with CUSTOMER or any of its affi liates. BEA has no liability to CUSTOMER or the end user for any and all liability, claims, demands, obligations, actions, losses, costs, damages, fees or expenses (including attorneys’...