Related Manuals for Stanley FATMAX TLM165S
Summary of Contents for Stanley FATMAX TLM165S
- Page 1 TLM165S, TLM165SI, TLM330S User Manual www.2helpU.com Please read these instructions before operating the product. DOC100270398...
- Page 4 TLM165S TLM165SI TLM330S...
- Page 9 12”...
- Page 11 Stanley Laser Distance Measurer The person responsible for the product TLM165S, TLM165SI and TLM330S must ensure that all users understand and Stanley hereby declares that the Stanley Laser adhere to these instructions. Distance Measurer TLM165S/TLM165SI/TLM330S is WARNING: in compliance with the Directive 2014/53/EU and to all The following label information is placed applicable EU directive requirements.
- Page 12 ALWAYS remove batteries if the device will Select the time. not be used for several months. • Choose to turn the tool off after 30 sec, 60 secs, NOTE: Ensure that the recommended 90 secs, or 300 secs. batteries are used. •...
- Page 13 Click the desired unit of measure. Point the tool's laser (Figure ) toward the wall or object whose distance you need to • 0'00" 0/00 measure (Figure • 0" 0/00 Press to measure the distance from the tool • 0'00" ft to the wall or object.
- Page 14 Subtracting 2 Measurements is not already displayed as the current function (Figure ), click the current function You can subtract one measurement from another icon and then select from the list of (Figure functions (Figure Point the tool's laser (Figure ) toward a wall Point the tool's laser (Figure ) toward...
- Page 15 Measure the length (Figure Measure the length of the first wall, floor, or object (Figure • Position the tool at one end of the wall, floor, or object and point the laser dot across the • Position the tool at one end of the target and length.
- Page 16 Measure the height (Figure Measure the height (Figure • Positon the tool at one end of the object and • Position the tool at one end of the object and point the laser dot across the height. point the laser dot across the height. (Figure (Figure shows where to position the shows where to position the tool if you are...
- Page 17 Distances to 2 Points is not already displayed as the current function (Figure ), click the current function You can use the distance to two points on a wall icon and then select from the list of functions or object (Double Indirect Height) to determine its (Figure height (Figure Point the laser at the highest point of the wall or...
- Page 18 Measuring from a Tripod is not already displayed as the current function (Figure ), click the current function If you are placing the tool on a tripod to measure icon and then select from the list of functions the height of a tall building, follow these steps (Figure (Figure Determine the distance between each stud, for...
- Page 19 THE BLUETOOTH® WORD MARK AND LOGOS ARE display the red laser dot. REGISTERED TRADEMARKS OWNED BY BLUETOOTH SIG, INC. AND ANY USE OF SUCH MARKS BY STANLEY TOOLS is not already displayed as the current IS UNDER LICENSE. APPLE AND THE APPLE LOGO ARE...
- Page 20 Clearing All Memory Warranty is not already displayed as the current STANLEY warrants this product for a period of Two (2) function (Figure ), click the current function years against deficiencies in material and workmanship.
- Page 21 Error Codes If INFO appears on the screen with a Code number, perform the corresponding Corrective Action. Code Description Corrective Action Received Signal Too Weak, Use the target plate or change the target surface. Measuring Time Too Long Received Signal Too High target surface.
- Page 22 TLM165S TLM165SI TLM330S Range 6in to 165ft 6in to 197ft 6in to 330ft (0.15m to 50m) (0.15m to 60m) (0.15m to 100m) Measuring Accuracy up to 10m: 1/16in (1.5mm) 10m-30m: 0.078/5/64in) additional (+/- 0.15mm/m) >30m: +/- 0.002in/ft (+/- 0.2mm/m) Resolution 1/16in (1mm) Laser Class Class 2 (IEC/EN60825-1: 2014)