Operating Tips; Brackets For Cordless Trimmer; Charging Stand And Battery Pack - Craftsman Weedwacker 172.74815 Operator's Manual

z:_ CAUTION: Before you begin trimming, only use the appropriate type of |
cutting line.
OPERATING TIPS
1. Before each use make sure the protective safety guard is tightly installed. Tighten tile
guard screw, but DO NOT over tighten.
2. Be sure to check the auxiliary handle before each use, to make sure it is firmly tightened.
3. Before trimming, inspect the area for string, wire, branches, rocks, toys, or other objects
that could be entangled in or thrown by the cutting line.
4. Stand with the cutting head tipped down at an angle in front, guiding the trimmer in a
semi-circular motion around you.
5. Cut from left to right whenever possible. Cutting to the right improves the unit's cutting
efficiency. Clippings are thrown away from the operator.
6. To produce a smoothly trimmed area, move the trimmer in and out of the area being cut
with constant speed and height.
7. Use only the tip of the cutting line to do the trimming, especially near walls and fences.
Trimming with the side of the cutting line may overload the motor, wear out the line faster,
and break the line more often.
8. DO NOT rest the trimmer spool on the ground while you are trimming.
This will cause spool wear.
9. When cutting vegetation that is over 6 inches in height, work from top to bottom in small
increments to avoid premature line wear or engine drag.
10. If the trimmer is not cutting correctly, the auto feed may not be operating correctly,
or the spool may be empty. Remove the spool and identify the problem. See page 22,
AUTOMATIC LINE FEED SYSTEM and page 23, REPLACE CUTTING LINE
and FiLLiNG SPOOL WITH CUTTING LINE.
BRACKETS FOR CORDLESS TRIMMER,
CHARGING STAND AND BATTERY PACK (Figs, 21,22, 22a and 23)
The 2 storage brackets are a convenient way to help keep your trimmer, charging stand
and battery pack organized, ready for use and stored up, out of the way in a dry place.
The trimmer's storage bracket mounts to wall with 4 screws and the trimmer can attach to
bracket two different ways (See Fig. 21 ).
The charging stand's bracket mounts with 4 screws also, but mount the charging stand
and its power cord into the bracket before screwing it down tight (See Figs. 22 and 22a).
NOTE: Before mounting the charging stand bracket to the wail,
make sure the power cord has access to a power outlet.
z_ WARNING: NEVER store your cordless trimmer, or leave your trimmer
unattended, with the battery pack installed.
Z_ WARNING: Store your trimmer, charging stand and battery pack up and
away from children. Children MUST NOT operate the tool.
24
}
}
BRACKETS FOR CORDLESS TRIMMER,
CHARGING STAND AND BATTERY PACK cont. (Figs. 21, 22, 22a and 23)
Trimmer mounts two ways
,
Fig. 21 .
j
W
Mount charging stand
into bracket before
mounting bracket
onto wall
Fig. 22
Attach charging stand's
power cord to bracket
and mount charging stand
bracket to wall. Make sure
power cord has access to
power outlet
Charging stand
and bracket properly
mounted to wall
Fig. 23
Insert battery pack into
charging stand to charge
The battery pack can be conveniently stored in the charging stand, but ALWAYS make sure
the charging stand is disconnected from the power supply when storing the battery pack
in the charging stand. SEE PAGES 8, 9, 10, 14 and 15 FOR IMPORTANT
BATTERY PACK INFORMATION.
NOTE:Tighten all mounting screws securely. Always check to make sure the bracket is tight to the wall, securely in place, and does not move.
Z_ WARNING:
The battery charging stand and trimmers are heavy; make sure
the storage brackets are securely mounted to the wall. Failure to do so can result
in damage to trimmer, charging stand and battery pack and can cause
serious personal injury.
25