Yamaha DX5 Owner's Manual page 24

This function will
operate only
if
the
AMPLITUDE MODULATION
SENSITIVITY
and
PITCH
MODULATION
SENSITIVITY voice parameters are set to
appropriate
values (see
CHAPTER
VI:
PROGRAMMING
VOICES).
This function
can be
set
independently
for
voice generator channels
A
and
B.
The
channel
In
which
this
function
is
to
be
progammed
can be
selected
by pressing
any
violet
BANK
or
VOICE
selector
In
the
corresponding channel.
The
selected
channel
will
be
indicated
immediately following
the function switch
number
at
the
left
of the
top
line
of
the
LCD
display-e.g.
"Func
PI
A"
or
"Func
PI B".
P1-J2:
BREATH CONTROLLER
ASSIGN
This function determines
which
type of effect will
be produced by the breath
controller.
Three options are available:
EBC
{EG
Bias Control),
AMD
(Amplitude
Modulation
Depth),
or
PMD
(Pitch
Modulation
Depth).
When
assigned to
EBC
the
result
is
either brilliance or
expression
(volume) control,
depending on
the
corresponding
voice parameter settings.
When
assigned
to
AMD
the result
is
either
tremolo
or
wow
control,
depending on
the
corresponding
voice parameter settings.
And when
assigned to
PMD
the result
is
vibrato control,
dependent on
the cor-
responding
voice
parameter settings
(see
CHAPTER
VI:
PROGRAMMING
VOICES).
Any
of
these
assignments can be used independently
or
combined.
Data
is
entered
in
the form
of a three-digit
binary
number-
-
"000". The
first
(leftmost)
digit
corresponds
to
EBC,
the
second
(center) digit to
AMD,
and
the third (right-
most)
digit
to
PMD.
Each
digit
can be
either a
"0"
(OFF)
or a
"1"
(ON), Consecutive
presses
on
the
+1
/YES/OFF
switch,
or raising
the
DATA ENTRY
control, results
in
the
following
sequence
of settings:
000
->
001 ->
01
^
Oil
-^
1
00
^
1
01
-.110-^111.
Pressing the
-1
/NO/OFF
switch
or
lowering the
DATA ENTRY
control reverses
this
sequence. "001
",
for
example,
assigns
PMD
only.
"1
01
"
assigns
EBC
and
PMD.
This function
can be
set
independently
for
voice generator
channels
A
and
B.
The
channel
in
which
this
function
is
to
be
progammed
can be selected
by pressing
any
violet
BANK
or
VOICE
selector
in
the
corresponding
channel.
The
selected
channel
will
be indicated
immediately following
the function
switch
number
at
the
left
of the
top
line
of
the
LCD
display--e.g.
"Func
PI
A"
or
"Func
PI B".
P2-J1:
AFTER
TOUCH
SENSITIVITY
Keyboard
after
touch
sensitivity
can be used
to
control the
depth of tremolo,
wow,
brilliance,
expression
(volume) or vibrato
type
effects,
according to
the
AFTER
TOUCH
ASSIGN
setting
described below. This function
sets
the
maximum
depth
of
the
assigned
effect
(maximum
depth
is
achieved with
maximum
pressure applied
to
the keyboard).
The data range
is
from
to
1
5.
At
after
touch
sensitivity
is
OFF, and
at
1
5
maximum
effect variation
can be achieved.
This function will
operate only
If
the
AMPLITUDE MODULATION
SENSITIVITY
and
PITCH
MODULATION
SENSITIVITY voice parameters are set to
appropriate
values
(see
CHAPTER
VI:
PROGRAMMING
VOICES).
This function
can be
set
independently
for
voice generator
channels
A
and
B.
The
channel
in
which
this
function
is
to
be
progammed can be
selected
by pressing
any
violet
BANK
or
VOICE
selector
in
the
corresponding channel.
The
selected
channel
will
be
indicated
immediately following
the function switch
number
at
the
left
of
the top
line
of
the
LCD
display-
-e.g.
"Func
P2A"
or
"Func P2B".
P2-J2:
AFTER
TOUCH ASSIGN
This function determines
which
type of effect will
be
produced by keyboard
after
touch
sensitivity.
Three options are available:
EBC
(EG Bias Control),
AMD
(Amplitude Modulation Depth), or
PMD
(Pitch
Modulation Depth).
When
assigned
to
EBC
the result
is
either brilliance or
expression
(volume)
control,
depending
23
>f'^J