NEC MDview 193 User Manual page 27

Tag6 Color Control
Tag7 Sharpness
DVI Selection
EDID EXTENSION
(Digital Input Only)
MDview 242/242-2,
MDview 262/262-2 and
Digital Input Only!
INPUT DEVICE
(Digital input only)
MDview 242/242-2, MDview
262/262-2 and Digital Input Only!
Video Detect
Off Timer
Colour Control Systems: Seven preset colour settings.
For preset settings 1, 2, 3 and 5, the following levels can be adjusted:
TEMPERATURE: Adjust the white temperature by increasing or decreasing this setting.
A lower colour temperature will make the screen reddish and a higher colour temperature
will make the screen bluish.
WHITE (White Balance): If TEMPERATURE needs further adjustment; the individual
R/ G/ B/ levels of the white point can be adjusted. To adjust the R/G/B levels, CUSTOM
must be showing as the TEMPERATURE selection.
HUE: Adjusts the hue of each colour*
the menu colour bars will show the amount of adjustment.
SATURATION: Adjusts the colour depth of each colour*
the colour vividness increases.
OFFSET: Adjusts the colour brightness of each colour*
colour Brightness increases.
*1: RED, YELLOW, GREEN, CYAN, BLUE and MAGENTA.
NATIVE, sRGB: Original colour presented by the LCD panel that is unadjustable.
PROGRAMMABLE: The colour tone that was set up with the downloaded application
software is reflected.
This is a digital capability for keeping a crisp image at all signal timings. It continuously
adjusts to maintain a distinct or soft image as you prefer, and is set independently
according to different timings. Press "Left" or "Right" to adjust.
This function selects the DVI input mode. When the DVI selection has been changed, you
must restart your computer. Press "Left" or "Right" to select.
AUTO: By using the DVI-D to DVI-D cable, the DVI SECTION is DIGITAL.
By using the D-SUB to DVI-A cable, the DVI SECTION is ANALOG.
DIGITAL: DVI digital input is available.
ANALOG: DVI analog input is available.
Selects the type of input to be used with EDID EXTENSION.
NORMAL: When a PC or other computer equipment is connected, select "NORMAL".
ENHANCED: When a DVD player or other type of high definition device is connected,
select "ENHANCED".
Note: Interlaced signals (480i, 576i, 1080i) are not supported. If you have any problems,
please refer to the Troubleshooting section of this User's Manual.
When EDID EXTENSION has been changed, the connected equipment has to be
restarted.
Selects the HDCP Enabled input device: Choose from PLAYER or PC.
PLAYER is the default setting and can be used with a PC input also.
If there is no image displayed when "PLAYER" is selected, change over to "PC".
Selects the method of video detection when more than one computer is connected.
Press "Left" or "Right" to select.
FIRST: The video input has to be switched to "FIRST" mode. When current video input
signal is not present, then the monitor searches for a video signal from the other video
input port. If the video signal is present in the other port, then the monitor switches the
video source input port to the new found video source automatically. The monitor will not
look for other video signals while the current video source is present.
LAST: The video input has to be switched to the "LAST" mode. When the monitor is
displaying a signal from the current source and a new secondary source is supplied to the
monitor, then the monitor will automatically switch to the new video source. When current
video input signal is not present, then the monitor searches for a video signal from the
other video input port. If the video signal is present in the other port, then the monitor
switches the video source input port to the new found video source automatically.
NONE: The Monitor will not search the other video input port unless the monitor is
turned on.
Monitor will automatically turn off after the preset time period from power on with the
ON/OFF function. When you select "ON", press "SELECT" and "Left" or "Right" to adjust.
Before powering off, a message will appear on the screen asking the user if they want to
delay the turn off time by 60 minutes. Press any OSD button to delay the turn off time.
English-25
1
. The change in colour will appear on screen and
1 . Press the "RIGHT" button and
1 . Press "RIGHT" button and the